Code flow now makes sense.
Signed-off-by: Felipe Balbi <[EMAIL PROTECTED]>
---
drivers/i2c/chips/twl4030-usb.c | 131 +++++++++++++++++++--------------------
1 files changed, 64 insertions(+), 67 deletions(-)
diff --git a/drivers/i2c/chips/twl4030-usb.c b/drivers/i2c/chips/twl4030-usb.c
index 136e1c6..2db1c63 100644
--- a/drivers/i2c/chips/twl4030-usb.c
+++ b/drivers/i2c/chips/twl4030-usb.c
@@ -496,45 +496,6 @@ static void usb_irq_disable(void)
return;
}
-static void twl4030_phy_suspend(int controller_off);
-static void twl4030_phy_resume(void);
-
-static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
-{
- int ret = IRQ_NONE;
- u8 val;
-
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_ISR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- goto done;
- }
-
- /* this interrupt line may be shared */
- if (!(val & USB_PRES))
- goto done;
-
- /* clear the interrupt */
- twl4030_i2c_write_u8(TWL4030_MODULE_INT, USB_PRES, REG_PWR_ISR1);
-
- /* action based on cable attach or detach */
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- goto done;
- }
-
- if (val & USB_PRES_RISING)
- twl4030_phy_resume();
- else
- twl4030_phy_suspend(0);
-
- ret = IRQ_HANDLED;
-
-done:
- return ret;
-}
-
static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
@@ -561,34 +522,6 @@ static void twl4030_phy_power(struct twl4030_usb *twl, int
on)
return;
}
-static void twl4030_usb_ldo_init(struct twl4030_usb *twl)
-{
- /* Enable writing to power configuration registers */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0xC0, PROTECT_KEY);
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0x0C, PROTECT_KEY);
-
- /* put VUSB3V1 LDO in active state */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
-
- /* input to VUSB3V1 LDO is from VBAT, not VBUS */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
-
- /* turn on 3.1V regulator */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB3V1_DEV_GRP);
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
-
- /* turn on 1.5V regulator */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB1V5_DEV_GRP);
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
-
- /* turn on 1.8V regulator */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB1V8_DEV_GRP);
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
-
- /* disable access to power configuration registers */
- twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, PROTECT_KEY);
-}
-
static void twl4030_phy_suspend(int controller_off)
{
struct twl4030_usb *twl = the_transceiver;
@@ -627,6 +560,70 @@ static void twl4030_phy_resume(void)
return;
}
+static void twl4030_usb_ldo_init(struct twl4030_usb *twl)
+{
+ /* Enable writing to power configuration registers */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0xC0, PROTECT_KEY);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0x0C, PROTECT_KEY);
+
+ /* put VUSB3V1 LDO in active state */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
+
+ /* input to VUSB3V1 LDO is from VBAT, not VBUS */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
+
+ /* turn on 3.1V regulator */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB3V1_DEV_GRP);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
+
+ /* turn on 1.5V regulator */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB1V5_DEV_GRP);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
+
+ /* turn on 1.8V regulator */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB1V8_DEV_GRP);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
+
+ /* disable access to power configuration registers */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, PROTECT_KEY);
+}
+
+static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
+{
+ int ret = IRQ_NONE;
+ u8 val;
+
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_ISR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ " line %d\n", __LINE__);
+ goto done;
+ }
+
+ /* this interrupt line may be shared */
+ if (!(val & USB_PRES))
+ goto done;
+
+ /* clear the interrupt */
+ twl4030_i2c_write_u8(TWL4030_MODULE_INT, USB_PRES, REG_PWR_ISR1);
+
+ /* action based on cable attach or detach */
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ " line %d\n", __LINE__);
+ goto done;
+ }
+
+ if (val & USB_PRES_RISING)
+ twl4030_phy_resume();
+ else
+ twl4030_phy_suspend(0);
+
+ ret = IRQ_HANDLED;
+
+done:
+ return ret;
+}
+
static int twl4030_set_suspend(struct otg_transceiver *x, int suspend)
{
if (suspend)
--
1.5.5.rc1.12.g660b9
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
