Hi Roger,
On 3/6/2014 2:19 PM, Roger Quadros wrote:
Hi George,
On 03/03/2014 03:53 PM, George Cherian wrote:
Add nodes for 2 instances each of
- ocp2scp
- USB PHY control module
- USB PHY
- dwc3_omap
- USB
for AM43xx.
Signed-off-by: George Cherian <george.cher...@ti.com>
---
arch/arm/boot/dts/am4372.dtsi | 99 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index 5a7cc38..90408b3 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -698,6 +698,105 @@
<&edma 11>;
dma-names = "tx", "rx";
};
+
+ am43xx_control_usb2phy1: control-phy@44e10620 {
+ compatible = "ti,control-phy-am437usb2";
Since this is the first usage of this compatible ID, we still have room to
change it to be better. Tony's suggestion was to use "ti,control-phy-am437-usb2"
Please see
http://article.gmane.org/gmane.linux.drivers.devicetree/64833
Okay.
+ reg = <0x44e10620 0x4>;
+ reg-names = "power";
+ status = "disabled";
Why disable something that is within the SoC and does not affect board
configurations?
Question applies for all the nodes in this patch except the ones that come out
on the
SoC pins. e.g. PHY.
Okay
+ };
+
+ am43xx_control_usb2phy2: control-phy@0x44e10628 {
+ compatible = "ti,control-phy-am437usb2";
+ reg = <0x44e10628 0x4>;
+ reg-names = "power";
+ status = "disabled";
+ };
+
+ ocp2scp0: ocp2scp@483a8000 {
+ compatible = "ti,omap-ocp2scp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "ocp2scp0";
+ status = "disabled";
+
+ usb2_phy1: usb2phy1@483a8000 {
should be
okay
usb2_phy1: phy@483a8000 {
+ compatible = "ti,am437x-usb2";
+ reg = <0x483a8000 0x8000>;
+ ctrl-module = <&am43xx_control_usb2phy1>;
+ clocks = <&clk_32768_ck>,
+ <&usb_otg_ss0_refclk960m>;
+ clock-names = "usb_phy_cm_clk32k",
+ "usb_otg_ss_refclk960m";
clock-names should be platform independent. Better option would be to
modify the usb2 driver to use names like "wkupclk" and "refclk"
The phy driver still does devm_get_clk using above clock names and not
"wkupclk" and "refclk".
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ ocp2scp1: ocp2scp@483e8000 {
+ compatible = "ti,omap-ocp2scp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "ocp2scp1";
+ status = "disabled";
+
+ usb2_phy2: usb2phy2@483e8000 {
+ compatible = "ti,am437x-usb2";
+ reg = <0x483e8000 0x8000>;
+ ctrl-module = <&am43xx_control_usb2phy2>;
+ clocks = <&clk_32768_ck>,
+ <&usb_otg_ss1_refclk960m>;
+ clock-names = "usb_phy_cm_clk32k",
+ "usb_otg_ss_refclk960m";
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ dwc3_1: omap_dwc3_1@48380000 {
+ compatible = "ti,am437x-dwc3";
+ ti,hwmods = "usb_otg_ss0";
+ reg = <0x48380000 0x10000>;
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ utmi-mode = <1>;
+ ranges;
+ status = "disabled";
+
+ usb1: usb@48390000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x48390000 0x17000>;
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ usb-phy = <&usb2_phy1>;
shouldn't this be phys = <&usb2_phy1>; ?
At the time of writing this patch phys property is still not in.
Also generic-phy conversion for dwc3 was recently posted by kishon.
+ phy-names = "usb2-phy";
what about
maximum-speed = "high-speed";
and
dr_mode = "otg"; ?
Done from board file. Actually maximum-speed I can set here.
dr_mode is a board property.
+ status = "disabled";
+ };
+ };
+
+ dwc3_2: omap_dwc3_2@483c0000 {
+ compatible = "ti,am437x-dwc3";
+ ti,hwmods = "usb_otg_ss1";
+ reg = <0x483c0000 0x10000>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ utmi-mode = <1>;
+ ranges;
+ status = "disabled";
+
+ usb2: usb@483d0000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x483d0000 0x17000>;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ usb-phy = <&usb2_phy2>;
+ phy-names = "usb2-phy";
+ status = "disabled";
+ };
+ };
+
};
};
cheers,
-roger
--
-George
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html