Copy all the platform data parameters to the driver's local data
structure 'omap_nand_info' and use it in the entire driver. This will
make it easer for device tree migration.
Signed-off-by: Roger Quadros <rog...@ti.com>
---
drivers/mtd/nand/omap2.c | 27 ++++++++++++++++++---------
1 file changed, 18 insertions(+), 9 deletions(-)
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index bb41796..e205863 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -184,15 +184,19 @@ static struct nand_ecclayout omap_oobinfo;
struct omap_nand_info {
struct nand_hw_control controller;
- struct omap_nand_platform_data *pdata;
struct mtd_info mtd;
struct nand_chip nand;
struct platform_device *pdev;
int gpmc_cs;
+ bool dev_ready;
+ enum nand_io xfer_type;
+ int devsize;
+ enum omap_ecc ecc_opt;
+ struct device_node *elm_of_node;
+
unsigned long phys_base;
void __iomem *gpmc_base;
- enum omap_ecc ecc_opt;
struct completion comp;
struct dma_chan *dma;
int gpmc_irq;
@@ -1708,6 +1712,11 @@ static int omap_nand_probe(struct platform_device *pdev)
info->gpmc_cs = pdata->cs;
info->of_node = pdata->of_node;
info->ecc_opt = pdata->ecc_opt;
+ info->dev_ready = pdata->dev_ready;
+ info->xfer_type = pdata->xfer_type;
+ info->devsize = pdata->devsize;
+ info->elm_of_node = pdata->elm_of_node;
+
mtd = &info->mtd;
mtd->priv = &info->nand;
mtd->name = dev_name(&pdev->dev);
@@ -1762,7 +1771,7 @@ static int omap_nand_probe(struct platform_device *pdev)
* chip delay which is slightly more than tR (AC Timing) of the NAND
* device and read status register until you get a failure or success
*/
- if (pdata->dev_ready) {
+ if (info->dev_ready) {
nand_chip->dev_ready = omap_dev_ready;
nand_chip->chip_delay = 0;
} else {
@@ -1771,7 +1780,7 @@ static int omap_nand_probe(struct platform_device *pdev)
}
/* scan NAND device connected to chip controller */
- nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16;
+ nand_chip->options |= info->devsize & NAND_BUSWIDTH_16;
if (nand_scan_ident(mtd, 1, NULL)) {
pr_err("nand device scan failed, may be bus-width mismatch\n");
err = -ENXIO;
@@ -1779,14 +1788,14 @@ static int omap_nand_probe(struct platform_device *pdev)
}
/* check for small page devices */
- if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) {
+ if ((mtd->oobsize < 64) && (info->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) {
pr_err("small page devices are not supported\n");
err = -EINVAL;
goto return_error;
}
/* re-populate low-level callbacks based on xfer modes */
- switch (pdata->xfer_type) {
+ switch (info->xfer_type) {
case NAND_OMAP_PREFETCH_POLLED:
nand_chip->read_buf = omap_read_buf_pref;
nand_chip->write_buf = omap_write_buf_pref;
@@ -1849,7 +1858,7 @@ static int omap_nand_probe(struct platform_device *pdev)
default:
dev_err(&pdev->dev,
- "xfer_type(%d) not supported!\n", pdata->xfer_type);
+ "xfer_type(%d) not supported!\n", info->xfer_type);
err = -EINVAL;
goto return_error;
}
@@ -1945,7 +1954,7 @@ static int omap_nand_probe(struct platform_device *pdev)
ecclayout->oobfree->offset =
ecclayout->eccpos[ecclayout->eccbytes - 1] + 1;
/* This ECC scheme requires ELM H/W block */
- if (is_elm_present(info, pdata->elm_of_node, BCH4_ECC) < 0) {
+ if (is_elm_present(info, info->elm_of_node, BCH4_ECC) < 0) {
pr_err("nand: error: could not initialize ELM\n");
err = -ENODEV;
goto return_error;
@@ -2011,7 +2020,7 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->ecc.read_page = omap_read_page_bch;
nand_chip->ecc.write_page = omap_write_page_bch;
/* This ECC scheme requires ELM H/W block */
- err = is_elm_present(info, pdata->elm_of_node, BCH8_ECC);
+ err = is_elm_present(info, info->elm_of_node, BCH8_ECC);
if (err < 0) {
pr_err("nand: error: could not initialize ELM\n");
goto return_error;
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
