This patch documents the device tree documentation required for
the ST usb3 controller glue layer found in STiH407 devices.
Signed-off-by: Giuseppe Cavallaro <peppe.cavall...@st.com>
Signed-off-by: Peter Griffin <peter.grif...@linaro.org>
---
Documentation/devicetree/bindings/usb/dwc3-st.txt | 58 +++++++++++++++++++++++
1 file changed, 58 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/dwc3-st.txt
diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt
b/Documentation/devicetree/bindings/usb/dwc3-st.txt
new file mode 100644
index 0000000..befd964
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt
@@ -0,0 +1,58 @@
+ST DWC3 glue logic
+
+This file documents the parameters for the dwc3-st driver.
+This driver provides the glue logic to use the dwc3 on STiH407 based platforms.
+
+Required properties:
+ - compatible : must be "st,stih407-dwc3"
+ - reg : glue logic base address and USB syscfg ctrl register offset
+ - reg-names : should be "reg-glue" and "syscfg-reg"
+ - st,syscon : should be phandle to system configuration node which
+ encompasses the glue registers
+ - resets : phandle pointing to the system powerdown controller
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+ with 'reg' property
+
+ - pinctl-names : A pinctrl state named "default" must be defined
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - pinctrl-0 : Pin control group
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - ranges : allows valid 1:1 translation between child's address space and
+ parent's address space
+
+Optional properties:
+ - st,dwc3-drd-device: to program the HC as "device" (static setup)
+
+Sub-nodes:
+The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
+example below. The DT binding details of dwc3 can be found in:
+Documentation/devicetree/bindings/usb/dwc3.txt
+
+Example:
+
+st_dwc3: dwc3@8f94000 {
+ status = "disabled";
+ compatible = "st,stih407-dwc3";
+ reg = <0x08f94000 0x1000>, <0x110 0x4>;
+ reg-names = "reg-glue", "syscfg-reg";
+ st,syscfg = <&syscfg_core>;
+ resets = <&powerdown STIH407_USB3_POWERDOWN>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb3>;
+ ranges;
+
+ dwc3: dwc3@9900000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x09900000 0x100000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>;
+
+ usb-phy = <&usb2_phy>, <&usb3_phy>;
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
