On Saturday 01 November 2014 02:39 AM, Hartmut Knaack wrote:
> Vignesh R schrieb am 27.10.2014 12:08:
>> The charge delay value is by default 0xB000. But it can be set to lower
>> values on some boards as long as false pen-ups are avoided. Lowering the
>> value increases the sampling rate (though current sampling rate is
>> sufficient for tsc operation). Hence charge delay has been made a DT
>> parameter.
>>
> I would recommend to use a few colons to separate some thoughts. Also, limit
> to 80 chars per line would be beneficial. See inline.
I will address this in v2
>> Signed-off-by: Vignesh R <vigne...@ti.com>
>> ---
>> .../devicetree/bindings/input/touchscreen/ti-tsc-adc.txt | 13
>> +++++++++++++
>> arch/arm/boot/dts/am335x-evm.dts | 1 +
>> 2 files changed, 14 insertions(+)
>>
>> diff --git
>> a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> index 878549ba814d..ac62769e70e4 100644
>> --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
>> @@ -28,6 +28,18 @@ Required properties:
>> ti,adc-channels: List of analog inputs available for ADC.
>> AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
>>
>> +Optional properties:
>> +- child "tsc"
>> + ti,charge-delay: Length of touch screen charge delay step in terms of
>> + ADC clock cycles. Charge delay value should be large
>> in order
>> + to avoid false pen-up events. This value affects the
>> overall
>> + sampling speed hence need to be kept as low as
>> possible while
> <...> speed, hence needs to be <...>
>> + avoiding false pen-up event. Start from a lower value
>> say 0x400
> <...> pen-up events. Start from a lower value, like 0x400, and increase <...>
>> + and increase value until false pen-up events are
>> avoided. The
>> + pen-up detection happens immediately after the charge
>> step
> <...> charge step, so this <...>
>> + so this does in fact function as a hardware knob for
>> adjusting
>> + the amount of "settling time".
>> +
>> Example:
>> tscadc: tscadc@44e0d000 {
>> compatible = "ti,am3359-tscadc";
>> @@ -36,6 +48,7 @@ Example:
>> ti,x-plate-resistance = <200>;
>> ti,coordiante-readouts = <5>;
>> ti,wire-config = <0x00 0x11 0x22 0x33>;
>> + ti,charge-delay = <0xB000>;
>> };
>>
>> adc {
>> diff --git a/arch/arm/boot/dts/am335x-evm.dts
>> b/arch/arm/boot/dts/am335x-evm.dts
>> index e2156a583de7..80be0462298b 100644
>> --- a/arch/arm/boot/dts/am335x-evm.dts
>> +++ b/arch/arm/boot/dts/am335x-evm.dts
>> @@ -641,6 +641,7 @@
>> ti,x-plate-resistance = <200>;
>> ti,coordinate-readouts = <5>;
>> ti,wire-config = <0x00 0x11 0x22 0x33>;
>> + ti,charge-delay = <0xB000>;
>> };
>>
>> adc {
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
