DRA72 EVM has a HDMI output. This patch adds the device tree nodes
required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkei...@ti.com>
Cc: devicet...@vger.kernel.org
---
arch/arm/boot/dts/dra72-evm.dts | 110 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 110 insertions(+)
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 4d8711713610..c752d7aa302d 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -19,6 +19,10 @@
reg = <0x80000000 0x40000000>; /* 1024 MB */
};
+ aliases {
+ display0 = &hdmi0;
+ };
+
evm_3v3: fixedregulator-evm_3v3 {
compatible = "regulator-fixed";
regulator-name = "evm_3v3";
@@ -35,6 +39,51 @@
compatible = "linux,extcon-usb-gpio";
id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
};
+
+ hdmi0: connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+ };
+
+ tpd12s015: encoder {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
+ <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
+ <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2,
HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
};
&dra7_pmx_core {
@@ -45,6 +94,13 @@
>;
};
+ i2c5_pins: pinmux_i2c5_pins {
+ pinctrl-single,pins = <
+ 0x2b4 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda
*/
+ 0x2b8 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl
*/
+ >;
+ };
+
nand_default: nand_default {
pinctrl-single,pins = <
0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */
@@ -144,6 +200,19 @@
0xb8 (PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */
>;
};
+
+ hdmi_pins: pinmux_hdmi_pins {
+ pinctrl-single,pins = <
+ 0x408 (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl
*/
+ 0x40c (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda
*/
+ >;
+ };
+
+ tpd12s015_pins: pinmux_tpd12s015_pins {
+ pinctrl-single,pins = <
+ 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD
*/
+ >;
+ };
};
&i2c1 {
@@ -280,6 +349,27 @@
};
};
+&i2c5 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+ clock-frequency = <400000>;
+
+ pcf_hdmi: pcf8575@26 {
+ compatible = "nxp,pcf8575";
+ reg = <0x26>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * initial state is used here to keep the mdio interface
+ * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
+ * VIN2_S0 driven high otherwise Ethernet stops working
+ * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
+ */
+ lines-initial-states = <0x0f2b>;
+ };
+};
+
&uart1 {
status = "okay";
};
@@ -569,3 +659,23 @@
};
};
};
+
+&dss {
+ status = "ok";
+
+ vdda_video-supply = <&ldo5_reg>;
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&ldo3_reg>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pins>;
+
+ port {
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+ };
+};
--
2.3.3
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
