Add support for vmmc_aux to switch to 1.8v. Also use "iov" instead of
"vdd" to indicate io voltage. This is in preparation for adding support
for io signal voltage switch.
Signed-off-by: Kishon Vijay Abraham I <kis...@ti.com>
---
drivers/mmc/host/omap_hsmmc.c | 48 +++++++++++++++++++++++++++--------------
1 file changed, 32 insertions(+), 16 deletions(-)
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index d884d8f..9c13157 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -244,11 +244,12 @@ static int omap_hsmmc_get_cover_state(struct device *dev)
return mmc_gpio_get_cd(host->mmc);
}
-static int omap_hsmmc_enable_supply(struct mmc_host *mmc)
+static int omap_hsmmc_enable_supply(struct mmc_host *mmc, int iov)
{
int ret;
struct omap_hsmmc_host *host = mmc_priv(mmc);
struct mmc_ios *ios = &mmc->ios;
+ int uvoltage;
if (mmc->supply.vmmc) {
ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
@@ -257,7 +258,25 @@ static int omap_hsmmc_enable_supply(struct mmc_host *mmc)
}
/* Enable interface voltage rail, if needed */
- if (mmc->supply.vqmmc && !host->vqmmc_enabled) {
+ if (mmc->supply.vqmmc) {
+ if (host->vqmmc_enabled) {
+ ret = regulator_disable(mmc->supply.vqmmc);
+ if (ret) {
+ dev_err(mmc_dev(mmc),
+ "vmmc_aux reg disable failed\n");
+ goto err_vqmmc;
+ }
+ host->vqmmc_enabled = 0;
+ }
+
+ uvoltage = (iov == VDD_165_195) ? VDD_1V8 : VDD_3V0;
+ ret = regulator_set_voltage(mmc->supply.vqmmc, uvoltage,
+ uvoltage);
+ if (ret) {
+ dev_err(mmc_dev(mmc), "vmmc_aux set voltage failed\n");
+ goto err_vqmmc;
+ }
+
ret = regulator_enable(mmc->supply.vqmmc);
if (ret) {
dev_err(mmc_dev(mmc), "vmmc_aux reg enable failed\n");
@@ -309,22 +328,19 @@ err_set_ocr:
}
static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on,
- int vdd)
+ int iov)
{
int ret;
+ int uvoltage;
if (!host->pbias)
return 0;
if (power_on) {
- if (vdd <= VDD_165_195)
- ret = regulator_set_voltage(host->pbias, VDD_1V8,
- VDD_1V8);
- else
- ret = regulator_set_voltage(host->pbias, VDD_3V0,
- VDD_3V0);
- if (ret < 0) {
- dev_err(host->dev, "pbias set voltage fail\n");
+ uvoltage = (iov <= VDD_165_195) ? VDD_1V8 : VDD_3V0;
+ ret = regulator_set_voltage(host->pbias, uvoltage, uvoltage);
+ if (ret) {
+ dev_err(host->dev, "pbias set voltage failed\n");
return ret;
}
@@ -348,7 +364,7 @@ static int omap_hsmmc_set_pbias(struct omap_hsmmc_host
*host, bool power_on,
return 0;
}
-static int omap_hsmmc_set_power(struct device *dev, int power_on, int vdd)
+static int omap_hsmmc_set_power(struct device *dev, int power_on, int iov)
{
struct omap_hsmmc_host *host =
platform_get_drvdata(to_platform_device(dev));
@@ -363,7 +379,7 @@ static int omap_hsmmc_set_power(struct device *dev, int
power_on, int vdd)
return 0;
if (mmc_pdata(host)->before_set_reg)
- mmc_pdata(host)->before_set_reg(dev, power_on, vdd);
+ mmc_pdata(host)->before_set_reg(dev, power_on, iov);
ret = omap_hsmmc_set_pbias(host, false, 0);
if (ret)
@@ -383,11 +399,11 @@ static int omap_hsmmc_set_power(struct device *dev, int
power_on, int vdd)
* chips/cards need an interface voltage rail too.
*/
if (power_on) {
- ret = omap_hsmmc_enable_supply(mmc);
+ ret = omap_hsmmc_enable_supply(mmc, iov);
if (ret)
return ret;
- ret = omap_hsmmc_set_pbias(host, true, vdd);
+ ret = omap_hsmmc_set_pbias(host, true, iov);
if (ret)
goto err_set_voltage;
} else {
@@ -397,7 +413,7 @@ static int omap_hsmmc_set_power(struct device *dev, int
power_on, int vdd)
}
if (mmc_pdata(host)->after_set_reg)
- mmc_pdata(host)->after_set_reg(dev, power_on, vdd);
+ mmc_pdata(host)->after_set_reg(dev, power_on, iov);
return 0;
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
