On Fri, May 15, 2009 at 11:40:41AM -0700, Kevin Hilman wrote:
> This patch is to sync the core linux-omap PM code with mainline. This
> code has evolved and been used for a while the linux-omap tree, but
> the attempt here is to finally get this into mainline.
>
> Following this will be a series of patches from the 'PM branch' of the
> linux-omap tree to add full PM hardware support from the linux-omap
> tree.
>
> Much of this PM core code was written by Jouni Hogander with
> significant contributions from Paul Walmsley as well as many others
> from Nokia, Texas Instruments and linux-omap community.
Overall comment, I think we need to rework the idle support code so
that enable_hlt/disable_hlt can be used even when pm_idle has been
overridden, rather than OMAP going off and inventing its own mechanisms.
> diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
> new file mode 100644
> index 0000000..2a2d1a3
> --- /dev/null
> +++ b/arch/arm/mach-omap2/pm24xx.c
> @@ -0,0 +1,557 @@
> +/*
> + * OMAP2 Power Management Routines
> + *
> + * Copyright (C) 2005 Texas Instruments, Inc.
> + * Copyright (C) 2006-2008 Nokia Corporation
> + *
> + * Written by:
> + * Richard Woodruff <r-woodru...@ti.com>
> + * Tony Lindgren
> + * Juha Yrjola
> + * Amit Kucheria <amit.kuche...@nokia.com>
> + * Igor Stoppa <igor.sto...@nokia.com>
> + *
> + * Based on pm.c for omap1
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/suspend.h>
> +#include <linux/sched.h>
> +#include <linux/proc_fs.h>
> +#include <linux/interrupt.h>
> +#include <linux/sysfs.h>
> +#include <linux/module.h>
> +#include <linux/delay.h>
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
> +#include <linux/time.h>
> +
> +#include <asm/mach/time.h>
> +#include <asm/mach/irq.h>
> +#include <asm/mach-types.h>
> +
> +#include <mach/irqs.h>
> +#include <mach/clock.h>
> +#include <mach/sram.h>
> +#include <mach/control.h>
> +#include <mach/gpio.h>
Should be linux/gpio.h
> +/*
> + * Note that you can use clock_event_device->min_delta_ns if you want to
> + * avoid reprogramming timer too often when using CONFIG_NO_HZ.
> + */
> +static void omap2_pm_idle(void)
> +{
> + local_irq_disable();
> + local_fiq_disable();
> +
> + if (!omap2_can_sleep()) {
> + if (!atomic_read(&sleep_block) && omap2_irq_pending())
> + goto out;
> + omap2_enter_mpu_retention();
> + goto out;
> + }
> +
> + if (omap2_irq_pending())
> + goto out;
> +
> + omap2_enter_full_retention();
> +
> +out:
> + local_fiq_enable();
> + local_irq_enable();
> +}
It's totally unclear what the comment above the function has to do with
the function itself.
> diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
> new file mode 100644
> index 0000000..0fb6bec
> --- /dev/null
> +++ b/arch/arm/mach-omap2/pm34xx.c
> @@ -0,0 +1,607 @@
> +/*
> + * OMAP3 Power Management Routines
> + *
> + * Copyright (C) 2006-2008 Nokia Corporation
> + * Tony Lindgren <t...@atomide.com>
> + * Jouni Hogander
> + *
> + * Copyright (C) 2005 Texas Instruments, Inc.
> + * Richard Woodruff <r-woodru...@ti.com>
> + *
> + * Based on pm.c for omap1
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/pm.h>
> +#include <linux/suspend.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/list.h>
> +#include <linux/err.h>
> +
> +#include <mach/gpio.h>
Should be linux/gpio.h
> +static void omap3_pm_idle(void)
> +{
> + local_irq_disable();
> + local_fiq_disable();
> +
> + if (!omap3_can_sleep())
> + goto out;
> +
> + if (omap_irq_pending())
> + goto out;
So what happens if an IRQ becomes pending at this precise point?
> +
> + omap_sram_idle();
> +
> +out:
> + local_fiq_enable();
> + local_irq_enable();
> +}
> + /* IRQ mode */
> + bic r0, r7, #0x1F
> + orr r0, r0, #0x12
> + msr cpsr, r0 /*go into IRQ mode*/
> + ldmia r3!,{r4-r6} /*load the SP and LR from SDRAM*/
> + mov sp, r4 /*update the SP */
> + mov lr, r5 /*update the LR */
> + msr spsr, r6 /*update the SPSR */
> +
> + /* ABORT mode */
> + bic r0, r7, #0x1F
> + orr r0, r0, #0x17
> + msr cpsr, r0 /* go into ABORT mode */
> + ldmia r3!,{r4-r6} /*load the SP and LR from SDRAM */
> + mov sp, r4 /*update the SP */
> + mov lr, r5 /*update the LR */
> + msr spsr, r6 /*update the SPSR */
> +
> + /* UNDEEF mode */
> + bic r0, r7, #0x1F
> + orr r0, r0, #0x1B
> + msr cpsr, r0 /*go into UNDEF mode */
> + ldmia r3!,{r4-r6} /*load the SP and LR from SDRAM */
> + mov sp, r4 /*update the SP*/
> + mov lr, r5 /*update the LR*/
> + msr spsr, r6 /*update the SPSR*/
> +
> + /* SYSTEM (USER) mode */
> + bic r0, r7, #0x1F
> + orr r0, r0, #0x1F
> + msr cpsr, r0 /*go into USR mode */
> + ldmia r3!,{r4-r6} /*load the SP and LR from SDRAM*/
> + mov sp, r4 /*update the SP */
> + mov lr, r5 /*update the LR */
> + msr spsr, r6 /*update the SPSR */
> + msr cpsr, r7 /*back to original mode*/
There is a function which re-initializes the abort mode registers already -
cpu_init(). Please use that if possible instead.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
