OMAP ES3.x supports portwise PHY or TLL mode of operation whereas in ES2.x all the three ports can either be in PHY mode or in TLL mode.Port3 can not be configured in PHY mode.
Port mode must be defined either PHY, TLL or UNKNOWN in platform files.Be careful of the scenario where one port is set as PHY and other in TLL but the OMAP silicon version is 2.x or earlier where this scenario is *not* supported. Changes are : - Setup all the bypass configuration in omap_start_ehc() based on ES version. - Remove UHH_HOSTCONFIG programming for bypass settings in omap_usb_utmi_init() Signed-off-by: Ajay Kumar Gupta <ajay.gu...@ti.com> --- Patch is updated to use [omap_rev() <= OMAP3430_REV_ES2_1] instead of CHIP_GE_OMAP3430ES3 as per Tony's suggestion. It's created against tony/ehci branch. drivers/usb/host/ehci-omap.c | 89 ++++++++++++++++++++++++------------------ 1 files changed, 51 insertions(+), 38 deletions(-) diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index 8a396b5..36fb183 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -32,7 +32,6 @@ * - move DPLL5 programming to clock fw * - add suspend/resume * - move workarounds to board-files - * - differentiate between ES2.x and ES3.x */ #include <linux/platform_device.h> @@ -102,6 +101,9 @@ #define OMAP_UHH_SYSSTATUS (0x14) #define OMAP_UHH_HOSTCONFIG (0x40) #define OMAP_UHH_HOSTCONFIG_ULPI_BYPASS (1 << 0) +#define OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS (1 << 0) +#define OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS (1 << 11) +#define OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS (1 << 12) #define OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN (1 << 2) #define OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN (1 << 3) #define OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN (1 << 4) @@ -185,16 +187,6 @@ static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask) unsigned reg; int i; - reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG); - reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS - | OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN; - reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN; - - /* Use UTMI Ports of TLL */ - ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg); - /* Program the 3 TLL channels upfront */ for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) { reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i)); @@ -244,6 +236,7 @@ static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask) static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) { unsigned long timeout = jiffies + msecs_to_jiffies(1000); + u8 tll_ch_mask = 0; unsigned reg = 0; int ret = 0; @@ -362,37 +355,58 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg); - if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) || - (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) || - (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY)) { + reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG); + + /* setup ULPI bypass and burst configurations */ + reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN + | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN + | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN); + reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN; + + /* Bypass the TLL module for PHY mode operation */ + if (omap_rev() <= OMAP3430_REV_ES2_1) { + dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1 \n"); + if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) || + (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) || + (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY)) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; + else + reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS; + } else { + dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n"); + if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; + else if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) + reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS; + + if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; + else if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) + reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS; - reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG); + if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY) + reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; + else if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL) + reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS; - reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN - | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN); - reg &= ~(OMAP_UHH_HOSTCONFIG_ULPI_BYPASS - | OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN); + } + ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg); + dev_dbg(omap->dev, "UHH setup done, uhh_base=%x\n", reg); - /* Bypass the TLL module for PHY mode operation */ - ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg); - dev_dbg(omap->dev, "Entered ULPI PHY MODE: success\n"); - } else if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) || + if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) || (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) || - (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)) { - - /* Enable UTMI mode for all 3 TLL channels */ - omap_usb_utmi_init(omap, - OMAP_TLL_CHANNEL_1_EN_MASK | - OMAP_TLL_CHANNEL_2_EN_MASK | - OMAP_TLL_CHANNEL_3_EN_MASK - ); - } else { - dev_err(hcd->self.controller, - "UNKOWN mode requested\n"); - ret = -EINVAL; - goto err_unknown_mode; + (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)) { + + if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) + tll_ch_mask |= OMAP_TLL_CHANNEL_1_EN_MASK; + if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) + tll_ch_mask |= OMAP_TLL_CHANNEL_2_EN_MASK; + if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL) + tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK; + + /* Enable UTMI mode for required TLL channels */ + omap_usb_utmi_init(omap, tll_ch_mask); } if (omap->phy_reset) { @@ -430,7 +444,6 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd) return 0; -err_unknown_mode: err_sys_status: clk_disable(omap->usbtll_ick); clk_put(omap->usbtll_ick); -- 1.6.2.4 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html