Tony Lindgren wrote:
> Hi,
>
> Sorry for the delay, have not had a chance to work on this for a few
> days.
>
> * Mike Rapoport <[email protected]> [091103 23:14]:
>>
>> Tony Lindgren wrote:
>>> * Mike Rapoport <[email protected]> [091102 23:10]:
>>>> On Mon, Nov 2, 2009 at 9:10 PM, Tony Lindgren <[email protected]> wrote:
>>>>> * Mike Rapoport <[email protected]> [091101 02:30]:
>>>>>> Tony Lindgren wrote:
>
> <snip snip>
>
>>> We can easily do something like this if we add char *muxname to
>>> struct omap_board_mux (untested):
>>>
>>> #define OMAP_MUX_SIGNAL(signal, mux_flags) \
>>> { \
>>> .muxname = #signal, \
>>> .flags = (mux_flags), \
>>> }
>>>
>>> #define OMAP_MUX_GPIO(gpio, mux_flags)
>>> \
>>> { \
>>> .muxname = gpio_##signal, \
>>> .flags = (mux_flags), \
>>> }
>>>
>>> #ifdef CONFIG_OMAP_MUX
>>> static struct omap_board_mux board_mux[] __initdata = {
>>> OMAP_MUX_SIGNAL(i2c1_scl, OMAP_PIN_INPUT),
>>> OMAP_MUX_GPIO(98, OMAP_PIN_INPUT_PULLUP),
>>> OMAP_MUX_GPIO(99, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_DYNAMIC),
>>> { .reg_offset = OMAP_MUX_TERMINATOR },
>>> };
>>> #endif
>>>
>>> Of course then we have to warn on potential duplicate signal names,
>>> but those can be specified using the register offset + mode as
>>> needed.
>
> Or use mode0_name.modeX_name for the full naming.
Agreed.
>>> Is the above close enough to what you have in mind regarding the
>>> board specific mux tables, or do you have still something else
>>> in mind?
>> It's closer :)
>
> OK, hopefully that means close to usable then :)
It became usable as soon as you don't have to patch common mux enumerations to
add board specific mux settings :)
With mode0_name.modeX_name the mux setup code is slightly more complicated but
once it's working adding new data both to SoC files and to the board files will
be easy.
>> What I have in mind is a simple wrapper macro defining mux configuration for
>> straightforward cases, just like a bunch of defines in
>> arch/arm/mach-omap2/include/mach/mux34xx.h in my earlier patch [1].
>> And just use OMAP_MUX_SIGNAL, or OMAP3_MUX for more complicated cases where
>> flags and/or OFF mode settings are required.
>> For instance, for making i2c1_scl to be actually routed to its pin you would
>> have
>>
>> static struct omap_board_mux board_mux[] __initdata = {
>> OMAP_MUX_I2C1_SCL,
>> ...
>> }
>>
>> and for dss_pclk to became hw_dbg12 you have
>>
>> static struct omap_board_mux board_mux[] __initdata = {
>> OMAP_MUX_PCLK_HW_DBG12,
>> ...
>> }
>
> The more I've been thinking about it, I think we should move away from using
> the register offsets if we can use the signal names instead. A lot of the
> board
> init code can be done in a generic way then, and should work across various
> omaps better.
>
> For example, see what setup_ehci_io_mux() becomes then:
>
> switch (port_mode[0]) {
> case EHCI_HCD_OMAP_MODE_PHY:
> omap_mux_init_signal("hsusb1_stp", OMAP_PIN_OUTPUT);
> omap_mux_init_signal("hsusb1_clk", OMAP_PIN_OUTPUT);
> omap_mux_init_signal("hsusb1_dir", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_nxt", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data0", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data1", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data2", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data3", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data4", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data5", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data6", OMAP_PIN_INPUT_PULLDOWN);
> omap_mux_init_signal("hsusb1_data7", OMAP_PIN_INPUT_PULLDOWN);
> break;
> ...
>
> Of course, that does not mean that we should not allow muxing by using the
> register offsets especially for board specific custom devices. But it helps
> with the common platform init code for the integrated devices.
>
>> Another my point was, that each board-* file will have all the mux settings
>> in
>> one consolidated place. Indeed, currently there are no many uses of
>> omap_cfg_reg
>> in the board files, but think of crappy bootloaders that fail to configure
>> half
>> of the pins or cases when you delibarately want to setup mux configuration in
>> kernel.
>
> Agreed. We should do it in the board-*.c files because bootloaders do what
> they
> do. And for common integrated devices we can do it in the common platform init
> code based on the nr_lines like we do for MMC and USB already.
>
>> I agree, that having the macros I'm talking about is more or less "syntactic
>> sugar" and I'm Ok to live without them :)
>
> OK, let's see how it works once I get back to working on it..
>
>> The most important that we don't need to add enumerated mux setting to
>> arch/arm/*omap*/mux.[ch] for each pin that was not there and mux setup can
>> completely defined by the board-* files.
>
> :)
>
> Except we still have it for mach-omap1. The mux registers are scattered in
> multiple registers, so let's not mess with that right now.
I have nether HW nor docs for omap1 so I afraid I won't be much help here...
> Regards,
>
> Tony
>
>>
>> [1] http://thread.gmane.org/gmane.linux.ports.arm.omap/25681
>
--
Sincerely yours,
Mike.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
