* Shilimkar, Santosh <santosh.shilim...@ti.com> [100130 09:52]: > > -----Original Message----- > > From: Tony Lindgren [mailto:t...@atomide.com] > > Sent: Saturday, January 30, 2010 9:55 PM > > To: Shilimkar, Santosh > > Cc: linux-arm-ker...@lists.infradead.org; linux-omap@vger.kernel.org > > Subject: Re: [PATCH 0/9] Initial multi-omap support for omap4 > > > > * Shilimkar, Santosh <santosh.shilim...@ti.com> [100130 04:49]: > > > > > Hi all, > > > > > > > > > > These patches allow compiling in also omap4 into the multi-omap > > > > > configuration. As I don't yet have omap4, I've only boot tested > > > > > these on omap2 and omap3. > > > > > > > > > > Somebody with an omap4 board please boot test these with the > > > > > omap3_defconfig and see what happens.. You might want to enable > > > > > DEBUG_LL and EARLY_PRINTK with earlyprintk on the cmdline too. > > > > Looks like this series have some dependent series because it doesn't > > > > apply on mainline. > > > > > > > > So I tested this directly on linux-omap "multi-omap4" branch. It boots > > > > sufficiently > > > > but doesn't proceed after "brd_init". Didn't get much time to debug so > > > > attached log > > > > > > Stand alone omap_4430sdp_defconfig also didn't fully boot on the > > > linux-omap "multi-omap4". > > > The log below shows that the serial platform data isn't configured > > > correctly. > > > > > > <6>io scheduler deadline registered > > > <6>io scheduler cfq registered (default) > > > <6>Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > > > <6>serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 104) is a ST16654 > > > <6>serial8250.1: ttyS0 at MMIO 0x4806a000 (irq = 105) is a ST16654 > > > > > > Below patch to fix the boot for omap_4430sdp_defconfig. Small typo really. > > > > > > diff --git a/arch/arm/plat-omap/include/plat/serial.h > > > b/arch/arm/plat-omap/inclu > > > index 67ffa08..83dce4c 100644 > > > --- a/arch/arm/plat-omap/include/plat/serial.h > > > +++ b/arch/arm/plat-omap/include/plat/serial.h > > > @@ -33,7 +33,7 @@ > > > > > > /* OMAP4 serial ports */ > > > #define OMAP4_UART1_BASE OMAP2_UART1_BASE > > > -#define OMAP4_UART2_BASE OMAP2_UART1_BASE > > > +#define OMAP4_UART2_BASE OMAP2_UART2_BASE > > > #define OMAP4_UART3_BASE 0x48020000 > > > #define OMAP4_UART4_BASE 0x4806e000
I've refreshed the second patch in the earlier multi-omap series with your fix above. > > Heh OK :) Sounds like at this point it makes sense to merge > > that into the original patch redo omap-for-linus partially. > > > > Can I also add your Acked-by for these patches then? > Yes please. OK, added your Acked-by to all the omap4 patches. Also fixed three checkpatch.pl warnings about long lines for the gpio patch. > > > For multi-omap build, for now I need to disable > > > [*] Reset unused clocks during boot > > > > Sounds like omap4 has some clocks left on from the bootloader > > that it should clk_get and clk_enable during init. That should > > be easy to track if you boot with "debug" in your cmdline and > > take a look at the list of unused clocks that are shut down > > with late_initcall. > I know it hangs when it tries to cut down UART3 ( console) clock. > The clock support got just recently merged and drivers are not > yet migrated so, need to still depend on bootloader. The work > is ongoing and soon the patches will be pushed. Few drivers > are planned to be handled in hwmod way so we were holding these > patches. OK Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html