This patch overrides nand ecc layout and bad block descriptor (for 8-bit device) to support hw ecc in romcode layout. So as to have in sync with ecc layout throughout; i.e. x-laod, u-boot and kernel.
This patch also enables to use romcode ecc for spd and zoom, by default. This enables to flash x-load, u-boot, kernel, FS images from kernel itself and compatiable with other tools. Signed-off-by: Sukumar Ghorai <s-gho...@ti.com> Signed-off-by: Vimal Singh <vimalsi...@ti.com> --- arch/arm/mach-omap2/board-flash.c | 2 +- drivers/mtd/nand/omap2.c | 34 ++++++++++++++++++++++++++++++++++ 2 files changed, 35 insertions(+), 1 deletions(-) diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c index ab31e7f..a15aab6 --- a/arch/arm/mach-omap2/board-flash.c +++ b/arch/arm/mach-omap2/board-flash.c @@ -144,7 +144,7 @@ __init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs) board_nand_data.cs = cs; board_nand_data.parts = nand_parts; board_nand_data.nr_parts = nr_parts; - board_nand_data.ecc_opt = OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT; + board_nand_data.ecc_opt = OMAP_ECC_HAMMING_CODE_HW; gpmc_nand_init(&board_nand_data); } diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c index d696026..4b777f0 --- a/drivers/mtd/nand/omap2.c +++ b/drivers/mtd/nand/omap2.c @@ -128,6 +128,20 @@ const int use_dma; const int use_interrupt; #endif +/* oob info generated runtime depending on ecc algorithm and layout selected */ +static struct nand_ecclayout omap_oobinfo; +/* Define some generic bad / good block scan pattern which are used + * while scanning a device for factory marked good / bad blocks + */ +static uint8_t scan_ff_pattern[] = { 0xff }; +static struct nand_bbt_descr bb_descrip_flashbased = { + .options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES, + .offs = 0, + .len = 1, + .pattern = scan_ff_pattern, +}; + + struct omap_nand_info { struct nand_hw_control controller; struct omap_nand_platform_data *pdata; @@ -959,6 +973,7 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) struct omap_nand_info *info; struct omap_nand_platform_data *pdata; int err; + int i, offset; pdata = pdev->dev.platform_data; if (pdata == NULL) { @@ -1093,6 +1108,25 @@ static int __devinit omap_nand_probe(struct platform_device *pdev) } } + /* rom code layout */ + if (pdata->ecc_opt != OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT) { + offset = (info->nand.options & NAND_BUSWIDTH_16) ? 2 : 1; + if (info->mtd.oobsize == 16) { + info->nand.badblock_pattern = &bb_descrip_flashbased; + omap_oobinfo.eccbytes = 3; + } else + omap_oobinfo.eccbytes = 3 * 4; + + for (i = 0; i < omap_oobinfo.eccbytes; i++) + omap_oobinfo.eccpos[i] = i+offset; + + omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes; + omap_oobinfo.oobfree->length = info->mtd.oobsize - + (offset + omap_oobinfo.eccbytes); + + info->nand.ecc.layout = &omap_oobinfo; + } + #ifdef CONFIG_MTD_PARTITIONS err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0); if (err > 0) -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html