From: Srinath <srin...@mistralsolutions.com>

AM3517/05 Craneboard has one EHCI interface on board using port1.

GPIO35 is used as power enable.
GPIO38 is used as port1 PHY reset.

History:
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%3A+Add+USB+EHCI+support&q=t

Signed-off-by: Srinath <srin...@mistralsolutions.com>
---
 arch/arm/mach-omap2/board-am3517crane.c |   40 +++++++++++++++++++++++++++++++
 1 files changed, 40 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-am3517crane.c 
b/arch/arm/mach-omap2/board-am3517crane.c
index 13ead33..6fd5dfe 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -28,8 +28,13 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
+#include <plat/usb.h>
 
 #include "mux.h"
+#include "control.h"
+
+#define GPIO_USB_POWER         35
+#define GPIO_USB_NRESET                38
 
 /* Board initialization */
 static struct omap_board_config_kernel am3517_crane_config[] __initdata = {
@@ -53,10 +58,45 @@ static void __init am3517_crane_init_irq(void)
        omap_gpio_init();
 }
 
+static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+       .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+       .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+       .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+       .phy_reset  = true,
+       .reset_gpio_port[0]  = GPIO_USB_NRESET,
+       .reset_gpio_port[1]  = -EINVAL,
+       .reset_gpio_port[2]  = -EINVAL
+};
+
 static void __init am3517_crane_init(void)
 {
+       int ret;
+
        omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
        omap_serial_init();
+
+       /* Configure GPIO for EHCI port */
+       omap_mux_init_gpio(GPIO_USB_POWER, OMAP_PIN_OUTPUT);
+
+       ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
+       if (ret < 0) {
+               pr_err("Cannot request GPIO %d\n", GPIO_USB_POWER);
+               return;
+       }
+
+       ret = gpio_direction_output(GPIO_USB_POWER, 1);
+       if (ret < 0)
+               goto err;
+
+       omap_mux_init_gpio(GPIO_USB_NRESET, OMAP_PIN_OUTPUT);
+       usb_ehci_init(&ehci_pdata);
+       return;
+
+err:
+       gpio_free(GPIO_USB_POWER);
+       pr_err("Unable to initialize EHCI power\n");
+       return;
 }
 
 MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
-- 
1.7.1.226.g770c5

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to