Kevin Hilman wrote, on 01/05/2011 05:28 PM:
Nishanth Menon<n...@ti.com> writes:
Beagle XM uses 3730 and the board design allows enabling 800MHz and 1GHz
OPPs. However, We need Smart reflex class 1.5 and ABB to enable 1GHz safely.
For the moment, we tweak the default table to allow for 800Mhz OPP usage.
Isn't this common to any board using 3730 (or 3630?)
no it is not. only certain boards are capable of higher frequencies -
there is a procedure called PDN analysis and vmin search that needs to
be performed to guarentee this.
IOW, what is Beagle specific about this?
beagle is one of the boards capable of higher frequencies.
Kevin
Reported-by: Koen Kooi<k...@beagleboard.org>
Tested-by: Koen Kooi<k...@beagleboard.org>
Signed-off-by: Nishanth Menon<n...@ti.com>
---
arch/arm/mach-omap2/board-omap3beagle.c | 50 +++++++++++++++++++++++++++++++
1 files changed, 50 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c
b/arch/arm/mach-omap2/board-omap3beagle.c
index 6c12760..0b99b80 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -23,6 +23,7 @@
#include<linux/gpio.h>
#include<linux/input.h>
#include<linux/gpio_keys.h>
+#include<linux/opp.h>
#include<linux/mtd/mtd.h>
#include<linux/mtd/partitions.h>
@@ -44,10 +45,12 @@
#include<plat/gpmc.h>
#include<plat/nand.h>
#include<plat/usb.h>
+#include<plat/omap_device.h>
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
+#include "pm.h"
#define NAND_BLOCK_SIZE SZ_128K
@@ -556,6 +559,52 @@ static struct omap_musb_board_data musb_board_data = {
.power = 100,
};
+static void __init beagle_opp_init(void)
+{
+ int r = 0;
+
+ /* Initialize the omap3 opp table */
+ if (omap3_opp_init()) {
+ pr_err("%s: opp default init failed\n", __func__);
+ return;
+ }
+
+ /* Custom OPP enabled for XM */
+ if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+ struct omap_hwmod *mh = omap_hwmod_lookup("mpu");
+ struct omap_hwmod *dh = omap_hwmod_lookup("iva");
+ struct device *dev;
+
+ if (!mh || !dh) {
+ pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
+ __func__, mh, dh);
+ r = -EINVAL;
+ } else {
+ /* Enable MPU 1GHz and lower opps */
+ dev =&mh->od->pdev.dev;
+ r = opp_enable(dev, 800000000);
+ /* TODO: MPU 1GHz needs SR and ABB */
+
+ /* Enable IVA 800MHz and lower opps */
+ dev =&dh->od->pdev.dev;
+ r |= opp_enable(dev, 660000000);
+ /* TODO: DSP 800MHz needs SR and ABB */
+ }
+ if (r) {
+ pr_err("%s: failed to enable higher opp %d\n",
+ __func__, r);
+ /*
+ * Cleanup - disable the higher freqs - we dont care
+ * about the results
+ */
+ dev =&mh->od->pdev.dev;
+ opp_disable(dev, 800000000);
+ dev =&dh->od->pdev.dev;
+ opp_disable(dev, 660000000);
+ }
+ }
+}
+
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
@@ -579,6 +628,7 @@ static void __init omap3_beagle_init(void)
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
beagle_display_init();
+ beagle_opp_init();
}
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
