On 05/05/2011 01:11 PM, Kevin Hilman wrote:
Peter Barada<peter.bar...@gmail.com> writes:
I've been working on getting the TI OMAPPSP-03.00.01.06 kernel to
properly suspend/resume on my DM37x board and all was going well until
I added OTG support to the kernel and on suspend, the IVA2 and CORE
pwrdms would not properly go into suspend. When comparing output from
/debug/pm-debug/registers/current to the TRM, I noticed the following:
MOD: CM_IVA2 (48014000)
04 => 00000017 20 => 00000001 24 => 00000001 34 => 00000001
40 => 00080a00 44 => 00000001 48 => 00000003
MOD: PRM_IVA2 (48316000)
50 => 00000007 e0 => 00ff0f05 e4 => 00000ff7 e8 => 00000ff7
f8 => 00000001
Looking at the TRM, the PRM_IVA2 registers are at 0x48306000, not
0x48316000. OMAP3430_IVA2_MOD is defined in prcm-common.h as -0x800
which means any module + reg_offset address calculation has to be
signed. Once I corrected the "unsigned short offset" declaration in
pm_module_def, rebuilt and tested again, IVA2/core pwrdms go into
suspend correctly (and addresses look correct):
Just to be clear, this should only affect the display of the registers,
not whether or not the power domains actually suspend correctly, right?
Or, did you actually notice via some other method that this powerdomain
was not hitting retention/off?
Yes the change affects the registers displayed, but since the address
calculation is incorrect with CONFIG_PM_DEBUG enabled, the PM_DEBUG code
is reading the CM_IVA2/PRM_IVA2 registers at incorrect addresses. On my
DM37x board when I suspended with OTG enabled (and without the patch), I
see the following on resume:
[ 496.168151] Powerdomain (iva2_pwrdm) didn't enter target state 1
(last power state 3)
[ 496.176025] Powerdomain (core_pwrdm) didn't enter target state 1
(last power state 3)
[ 496.183898] Could not enter target state in pm_suspend
With the patch (and same kernel config) I see the following on resume:
[ 234.867889] Successfully put all powerdomains to target state
Before enabling the OTG code all powerdomains went into suspend.
It could be that accessing registers at the incorrect addresses is
causing DM37x to keep those domains out of retention...
Kevin
Signed-off-by: Peter Barada<peter.bar...@logicpd.com>
diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c
index 125f565..b731ef3 100644
--- a/arch/arm/mach-omap2/pm-debug.c
+++ b/arch/arm/mach-omap2/pm-debug.c
@@ -199,7 +199,7 @@ enum {
struct pm_module_def {
char name[8]; /* Name of the module */
short type; /* CM or PRM */
- unsigned short offset;
+ short offset;
int low; /* First register address on this module */
int high; /* Last register address on this module */
};
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Peter Barada
peter.bar...@gmail.com
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
