Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Keshava Munegowda <keshava_mgo...@ti.com>
Reviewed-by: Partha Basak <part...@india.ti.com>
---
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 227 ++++++++++++++++++++++++++++
1 files changed, 227 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index 59fdb9f..b8ca690 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -84,6 +84,8 @@ static struct omap_hwmod omap3xxx_mcbsp4_hwmod;
static struct omap_hwmod omap3xxx_mcbsp5_hwmod;
static struct omap_hwmod omap3xxx_mcbsp2_sidetone_hwmod;
static struct omap_hwmod omap3xxx_mcbsp3_sidetone_hwmod;
+static struct omap_hwmod omap34xx_usb_host_hs_hwmod;
+static struct omap_hwmod omap34xx_usb_tll_hs_hwmod;
/* L3 -> L4_CORE interface */
static struct omap_hwmod_ocp_if omap3xxx_l3_main__l4_core = {
@@ -3196,6 +3198,226 @@ static struct omap_hwmod omap3xxx_mmc3_hwmod = {
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430),
};
+/*
+ * 'usb_host_hs' class
+ * high-speed multi-port usb host controller
+ */
+static struct omap_hwmod_ocp_if omap34xx_usb_host_hs__l3_main_2 = {
+ .master = &omap34xx_usb_host_hs_hwmod,
+ .slave = &omap3xxx_l3_main_hwmod,
+ .clk = "core_l3_ick",
+ .user = OCP_USER_MPU,
+};
+
+static struct omap_hwmod_class_sysconfig omap34xx_usb_host_hs_sysc = {
+ .rev_offs = 0x0000,
+ .sysc_offs = 0x0010,
+ .syss_offs = 0x0014,
+ .sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_CLOCKACTIVITY |
+ SYSC_HAS_SIDLEMODE | SYSC_HAS_ENAWAKEUP |
+ SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE),
+ .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+ MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART),
+ .sysc_fields = &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap34xx_usb_host_hs_hwmod_class = {
+ .name = "usb_host_hs",
+ .sysc = &omap34xx_usb_host_hs_sysc,
+};
+
+static struct omap_hwmod_ocp_if *omap34xx_usb_host_hs_masters[] = {
+ &omap34xx_usb_host_hs__l3_main_2,
+};
+
+static struct omap_hwmod_addr_space omap34xx_usb_host_hs_addrs[] = {
+ {
+ .name = "uhh",
+ .pa_start = 0x48064000,
+ .pa_end = 0x480643ff,
+ .flags = ADDR_TYPE_RT
+ },
+ {
+ .name = "ohci",
+ .pa_start = 0x48064400,
+ .pa_end = 0x480647ff,
+ },
+ {
+ .name = "ehci",
+ .pa_start = 0x48064800,
+ .pa_end = 0x48064cff,
+ },
+ {}
+};
+
+static struct omap_hwmod_ocp_if omap34xx_usb_host_hs__ick = {
+ .master = &omap3xxx_l4_core_hwmod,
+ .slave = &omap34xx_usb_host_hs_hwmod,
+ .clk = "usbhost_ick",
+ .addr = omap34xx_usb_host_hs_addrs,
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+/*
+ * This clock should be on/off only with main clock; If auto idle is set,
+ * the usbhs controller prevents the omap to enter in to low power mode,
+ * hence don't use auto idle here.
+ */
+ .flags = OCPIF_SWSUP_IDLE,
+};
+
+static struct omap_hwmod_ocp_if *omap34xx_usb_host_hs_slaves[] = {
+ &omap34xx_usb_host_hs__ick,
+};
+
+static struct omap_hwmod_opt_clk omap34xx_usb_host_hs_opt_clks[] = {
+ { .role = "ehci_logic_fck", .clk = "usbhost_120m_fck", },
+};
+
+static struct omap_hwmod_irq_info omap34xx_usb_host_hs_irqs[] = {
+ { .name = "ohci-irq", .irq = 76 },
+ { .name = "ehci-irq", .irq = 77 },
+ { .irq = -1 }
+};
+
+static struct omap_hwmod omap34xx_usb_host_hs_hwmod = {
+ .name = "usb_host_hs",
+ .class = &omap34xx_usb_host_hs_hwmod_class,
+ .clkdm_name = "l3_init_clkdm",
+ .mpu_irqs = omap34xx_usb_host_hs_irqs,
+ .main_clk = "usbhost_48m_fck",
+ .prcm = {
+ .omap2 = {
+ .module_offs = OMAP3430ES2_USBHOST_MOD,
+ .prcm_reg_id = 1,
+ .module_bit = OMAP3430ES2_EN_USBHOST1_SHIFT,
+ .idlest_reg_id = 1,
+ .idlest_idle_bit = OMAP3430ES2_ST_USBHOST_IDLE_SHIFT,
+ .idlest_stdby_bit = OMAP3430ES2_ST_USBHOST_STDBY_SHIFT,
+ },
+ },
+ .opt_clks = omap34xx_usb_host_hs_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(omap34xx_usb_host_hs_opt_clks),
+ .slaves = omap34xx_usb_host_hs_slaves,
+ .slaves_cnt = ARRAY_SIZE(omap34xx_usb_host_hs_slaves),
+ .masters = omap34xx_usb_host_hs_masters,
+ .masters_cnt = ARRAY_SIZE(omap34xx_usb_host_hs_masters),
+/*
+ * Errata: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
+ * id: i660
+ *
+ * Description:
+ * In the following configuration :
+ * - USBHOST module is set to smart-idle mode
+ * - PRCM asserts idle_req to the USBHOST module ( This typically happens
+ * when the system is going to a low power mode : all ports have been
+ * suspended, the master part of the USBHOST module has entered the
+ * standby state, and SW has cut the functional clocks.)
+ * - an USBHOST interrupt occurs before the module is able to answer
+ * idle_ack, typically a remote wakeup IRQ.
+ * Then the USB HOST module will enter a deadlock situation where it is no
+ * more accessible nor functional.
+ *
+ * Workaround:
+ * Don't use smart idle; use only force idle, hence HWMOD_SWSUP_SIDLE
+ */
+
+/* Errata: USB host EHCI may stall when entering smart-standby mode
+ * Id: i571
+ *
+ * Description:
+ * When the USBHOST module is set to smart-standby mode, and when it is
+ * ready to enter the standby state (i.e. all ports are suspended and
+ * all attached devices are in suspend mode), then it can wrongly assert
+ * the Mstandby signal too early while there are still some residual OCP
+ * transactions ongoing. If this condition occurs, the internal state
+ * machine may go to an undefined state and the USB link may be stuck
+ * upon the next resume.
+ *
+ * Workaround:
+ * Don't use smart standby; use only force standby,
+ * hence HWMOD_SWSUP_MSTANDBY
+ */
+
+/* During system boot; If the hwmod framework resets the module
+ * the module will have smart idle settings; which can lead to deadlock
+ * (above Errata Id:i660); so, dont reset the module during boot;
+ * Use HWMOD_INIT_NO_RESET.
+ */
+ .flags = HWMOD_SWSUP_SIDLE | HWMOD_SWSUP_MSTANDBY |
+ HWMOD_INIT_NO_RESET,
+ .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430),
+};
+
+/*
+ * 'usb_tll_hs' class
+ * usb_tll_hs module is the adapter on the usb_host_hs ports
+ */
+static struct omap_hwmod_class_sysconfig omap34xx_usb_tll_hs_sysc = {
+ .rev_offs = 0x0000,
+ .sysc_offs = 0x0010,
+ .syss_offs = 0x0014,
+ .sysc_flags = (SYSC_HAS_CLOCKACTIVITY | SYSC_HAS_SIDLEMODE |
+ SYSC_HAS_ENAWAKEUP | SYSC_HAS_SOFTRESET |
+ SYSC_HAS_AUTOIDLE),
+ .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+ .sysc_fields = &omap_hwmod_sysc_type1,
+};
+
+static struct omap_hwmod_class omap34xx_usb_tll_hs_hwmod_class = {
+ .name = "usb_tll_hs",
+ .sysc = &omap34xx_usb_tll_hs_sysc,
+};
+
+static struct omap_hwmod_irq_info omap34xx_usb_tll_hs_irqs[] = {
+ { .name = "tll-irq", .irq = 78 },
+ { .irq = -1 }
+};
+
+static struct omap_hwmod_addr_space omap34xx_usb_tll_hs_addrs[] = {
+ {
+ .name = "tll",
+ .pa_start = 0x48062000,
+ .pa_end = 0x48062fff,
+ .flags = ADDR_TYPE_RT
+ },
+ {}
+};
+
+static struct omap_hwmod_ocp_if omap34xx_ick_cfg__usb_tll_hs = {
+ .clk = "usbtll_ick",
+ .addr = omap34xx_usb_tll_hs_addrs,
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+/*
+ * This clock should be on/off only with main clock; If auto idle is set,
+ * the usbhs controller prevents the omap to enter in to low power mode,
+ * hence don't use auto idle here.
+ */
+ .flags = OCPIF_SWSUP_IDLE,
+};
+
+static struct omap_hwmod_ocp_if *omap34xx_usb_tll_hs_slaves[] = {
+ &omap34xx_ick_cfg__usb_tll_hs,
+};
+
+static struct omap_hwmod omap34xx_usb_tll_hs_hwmod = {
+ .name = "usb_tll_hs",
+ .class = &omap34xx_usb_tll_hs_hwmod_class,
+ .clkdm_name = "l3_init_clkdm",
+ .mpu_irqs = omap34xx_usb_tll_hs_irqs,
+ .main_clk = "usbtll_fck",
+ .prcm = {
+ .omap2 = {
+ .module_offs = CORE_MOD,
+ .prcm_reg_id = 3,
+ .module_bit = OMAP3430ES2_EN_USBTLL_SHIFT,
+ .idlest_reg_id = 3,
+ .idlest_idle_bit = OMAP3430ES2_ST_USBTLL_SHIFT,
+ },
+ },
+ .slaves = omap34xx_usb_tll_hs_slaves,
+ .slaves_cnt = ARRAY_SIZE(omap34xx_usb_tll_hs_slaves),
+ .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430),
+};
+
static __initdata struct omap_hwmod *omap3xxx_hwmods[] = {
&omap3xxx_l3_main_hwmod,
&omap3xxx_l4_core_hwmod,
@@ -3225,6 +3447,11 @@ static __initdata struct omap_hwmod *omap3xxx_hwmods[] =
{
&omap3xxx_uart2_hwmod,
&omap3xxx_uart3_hwmod,
&omap3xxx_uart4_hwmod,
+
+ /* usb host class */
+ &omap34xx_usb_host_hs_hwmod,
+ &omap34xx_usb_tll_hs_hwmod,
+
/* dss class */
&omap3430es1_dss_core_hwmod,
&omap3xxx_dss_core_hwmod,
--
1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
