From: "Govindraj.R" <govindraj.r...@ti.com>
The following commit:
(7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
added default pads for all uarts. But not all boards tend to
use all uarts and most of unused uart pins are muxed for
other purpose. This commit breaks the modules which where trying
to use unused uart pins on their boards.
So remove the default pads adding.
Cc: Felipe Balbi <ba...@ti.com>
Cc: Kevin Hilman <khil...@ti.com>
Cc: Russ Dill <russ.d...@gmail.com>
Reported-by: Tony Lindgren <t...@atomide.com>
Signed-off-by: Govindraj.R <govindraj.r...@ti.com>
---
arch/arm/mach-omap2/serial.c | 116 ------------------------------------------
1 files changed, 0 insertions(+), 116 deletions(-)
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index c9503a7..1554233 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -120,124 +120,8 @@ static void omap_uart_set_smartidle(struct
platform_device *pdev) {}
#endif /* CONFIG_PM */
#ifdef CONFIG_OMAP_MUX
-static struct omap_device_pad default_uart1_pads[] __initdata = {
- {
- .name = "uart1_cts.uart1_cts",
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- },
- {
- .name = "uart1_rts.uart1_rts",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart1_tx.uart1_tx",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart1_rx.uart1_rx",
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- .idle = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- },
-};
-
-static struct omap_device_pad default_uart2_pads[] __initdata = {
- {
- .name = "uart2_cts.uart2_cts",
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- },
- {
- .name = "uart2_rts.uart2_rts",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart2_tx.uart2_tx",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart2_rx.uart2_rx",
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- .idle = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- },
-};
-
-static struct omap_device_pad default_uart3_pads[] __initdata = {
- {
- .name = "uart3_cts_rctx.uart3_cts_rctx",
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
- },
- {
- .name = "uart3_rts_sd.uart3_rts_sd",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart3_tx_irtx.uart3_tx_irtx",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart3_rx_irrx.uart3_rx_irrx",
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
- .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
- .idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
- },
-};
-
-static struct omap_device_pad default_omap36xx_uart4_pads[] __initdata = {
- {
- .name = "gpmc_wait2.uart4_tx",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "gpmc_wait3.uart4_rx",
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
- .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE2,
- .idle = OMAP_PIN_INPUT | OMAP_MUX_MODE2,
- },
-};
-
-static struct omap_device_pad default_omap4_uart4_pads[] __initdata = {
- {
- .name = "uart4_tx.uart4_tx",
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
- },
- {
- .name = "uart4_rx.uart4_rx",
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
- .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
- .idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
- },
-};
-
static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
{
- switch (bdata->id) {
- case 0:
- bdata->pads = default_uart1_pads;
- bdata->pads_cnt = ARRAY_SIZE(default_uart1_pads);
- break;
- case 1:
- bdata->pads = default_uart2_pads;
- bdata->pads_cnt = ARRAY_SIZE(default_uart2_pads);
- break;
- case 2:
- bdata->pads = default_uart3_pads;
- bdata->pads_cnt = ARRAY_SIZE(default_uart3_pads);
- break;
- case 3:
- if (cpu_is_omap44xx()) {
- bdata->pads = default_omap4_uart4_pads;
- bdata->pads_cnt =
- ARRAY_SIZE(default_omap4_uart4_pads);
- } else if (cpu_is_omap3630()) {
- bdata->pads = default_omap36xx_uart4_pads;
- bdata->pads_cnt =
- ARRAY_SIZE(default_omap36xx_uart4_pads);
- }
- break;
- default:
- break;
- }
}
#else
static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
--
1.7.9
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
