"Joe Woodward" <j...@terrafix.co.uk> writes: > -----Original Message----- > From: Kevin Hilman <khil...@ti.com> > To: "Joe Woodward" <j...@terrafix.co.uk> > Cc: "linux-omap\@vger.kernel.org" <linux-omap@vger.kernel.org> > Date: Tue, 10 Jul 2012 16:58:18 -0700 > Subject: Re: PM/RTC 3.5-rc5: System suspends fails when not built with RTC? > >> "Joe Woodward" <j...@terrafix.co.uk> writes: >> >> > I've got 3.5-rc5 with the following patches applied to get system >> suspend working on OMAP3: >> > - fix the DSS: OMAPDSS: Use PM notifiers for system suspend >> > - fix the 32KHz clock: ARM: OMAP2+: hwmod code/clockdomain data: >> fix 32K sync timer >> > >> > This has been built with the omap2plus_defconfig. >> > >> > However, If I disable the RTC (i.e. >> CONFIG_RTC_CLASS/CONFIG_RTC_DRV_TWL4030) and rebuild then when >> suspending the device never wakes up. >> > >> > That is, I can't get any wakeups to happen (either through the >> console, or GPIO buttons) hence I'm assuming the kernel has crashed... >> > >> > Any ideas? >> > >> > As far as I know there is no dependency on the RTC in 3.4, and with >> the RTC compiled in I never see a problem on 3.5-rc5. >> >> There is definitely a bug in the EHCI driver in v3.5 that cause a hang >> in suspend, but the RTC connection is very strange. >> >> I was not able to reproduce this. >> >> Can you try the same with my current 'pm' branch[1]. I've got a >> handful >> of additional fixes there for various other problems where both MMC and >> EHCI are preventing sucessful suspend with the default >> omap2plus_defconfig. (note the EHCI fix is simply diabling it in the >> defconfig.) >> >> Kevin >> > > Hi Kevin, > > Thanks for looking in to this.
And thanks for your detailed bug reports. > I've taken a copy of the PM branch with tag "pm-20120710" and built with > omap2plus_defconfig. > > But I get several warnings during boot, and suspend works - but almost > nothing enters the target states: > > Warnings include: > [ 0.000000] clockdomain: mpu_clkdm: powerdomain ¬õ`À8ºsÀ does not exist This one is suspicious. > [ 2.311004] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk > [ 2.317382] omap_hsmmc omap_hsmmc.0: unable to obtain RX DMA engine > channel 62 > [ 2.325256] omap_hsmmc omap_hsmmc.1: Failed to get debounce clk > [ 2.331512] omap_hsmmc omap_hsmmc.1: unable to obtain RX DMA engine > channel 48 These are normal because DMA engine is not compiled in with omap2plus_defconfig. MMC wont' work unless you build in DMA engine, but that doesn't matter for trying to figure out your problem. > [ 2.447784] platform omap_hsmmc.0: omap_device_late_idle: enabled but no > driver. Idling > [ 2.456359] platform omap_hsmmc.1: omap_device_late_idle: enabled but no > driver. Idling This is expected because of the failed MMC probe. > # echo mem > /sys/power/state > [ 107.398956] PM: Syncing filesystems ... done. > [ 107.413757] Freezing user space processes ... (elapsed 0.02 seconds) done. > [ 107.443481] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) > done. > [ 107.474700] Suspending console(s) (use no_console_suspend to debug) > [ 107.493560] PM: suspend of devices complete after 9.246 msecs > [ 107.496063] PM: late suspend of devices complete after 2.502 msecs > [ 107.500427] PM: noirq suspend of devices complete after 4.302 msecs > [ 107.500488] Disabling non-boot CPUs ... > [ 108.446838] Powerdomain (iva2_pwrdm) didn't enter target state 1 > [ 108.446868] Powerdomain (dss_pwrdm) didn't enter target state 1 > [ 108.446868] Powerdomain (per_pwrdm) didn't enter target state 1 > [ 108.446868] Powerdomain (core_pwrdm) didn't enter target state 1 > [ 108.446899] Powerdomain (usbhost_pwrdm) didn't enter target state 1 > [ 108.446899] Could not enter target state in pm_suspend > [ 108.448852] PM: noirq resume of devices complete after 1.769 msecs > [ 108.451873] PM: early resume of devices complete after 1.556 msecs > [ 108.459716] PM: resume of devices complete after 7.690 msecs > [ 108.541748] Restarting tasks ... done. > sh: write error: Operation not permitted > > This is all on an Overo AirSTORM (3703-based) plugged in to a GUMSTIX PALO43 > dev board. Hmm, interesting, I don't see this on my 3730-based Over FireSTORM. But, after "converting" mine into an AirStorm[1], I see the same errors as you're seeing. We're obviously doing something wrong when IVA and/or SGX are not present, so I will look into it. Thanks for testing, Kevin [1] diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index 40373db..c8e5a6c 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -237,8 +237,8 @@ void __init omap3xxx_check_features(void) status = omap_ctrl_readl(OMAP3_CONTROL_OMAP_STATUS); OMAP3_CHECK_FEATURE(status, L2CACHE); - OMAP3_CHECK_FEATURE(status, IVA); - OMAP3_CHECK_FEATURE(status, SGX); + /* OMAP3_CHECK_FEATURE(status, IVA); */ + /* OMAP3_CHECK_FEATURE(status, SGX); */ OMAP3_CHECK_FEATURE(status, NEON); OMAP3_CHECK_FEATURE(status, ISP); if (cpu_is_omap3630()) -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html