On Thu, Mar 14, 2013 at 4:48 PM, Jon Hunter <jon-hun...@ti.com> wrote:
> Hi Javier,
>
> On 03/14/2013 10:09 AM, Javier Martinez Canillas wrote:
>> Besides being used to interface with external memory devices,
>> the General-Purpose Memory Controller can be used to connect
>> Pseudo-SRAM devices such as ethernet controllers to OMAP2+
>> processors using the TI GPMC as a data bus.
>>
>> This patch allows an ethernet chip to be defined as an GPMC
>> child device node.
>>
>> Signed-off-by: Javier Martinez Canillas <javier.marti...@collabora.co.uk>
>> ---
>> Documentation/devicetree/bindings/net/gpmc-eth.txt | 90
>> ++++++++++++++++++++
>> arch/arm/mach-omap2/gpmc.c | 8 ++
>> 2 files changed, 98 insertions(+), 0 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/net/gpmc-eth.txt
>>
>> diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt
>> b/Documentation/devicetree/bindings/net/gpmc-eth.txt
>> new file mode 100644
>> index 0000000..c45363c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt
>> @@ -0,0 +1,90 @@
>> +Device tree bindings for Ethernet chip connected to TI GPMC
>> +
>> +Besides being used to interface with external memory devices, the
>> +General-Purpose Memory Controller can be used to connect Pseudo-SRAM devices
>> +such as ethernet controllers to processors using the TI GPMC as a data bus.
>> +
>> +Ethernet controllers connected to TI GPMC are represented as child nodes of
>> +the GPMC controller with an "ethernet" name.
>> +
>> +All timing relevant properties as well as generic GPMC child properties are
>> +explained in a separate documents. Please refer to
>> +Documentation/devicetree/bindings/bus/ti-gpmc.txt
>> +
>> +Required properties:
>> +- bank-width: Address width of the device in bytes. GPMC
>> supports 8-bit
>> + and 16-bit devices and so must be either 1 or 2 bytes.
>
> I am wondering if we should use reg-io-width here. The smsc driver is
> using this to determine the width of the device. And so I am wondering
> if this could cause problems.
>
> Obviously this complicates gpmc_probe_generic_child() a little, but may
> be would could pass the name of the width property to
> gpmc_probe_generic_child() as well. What do you think?
>
Hi Jon,
Well now I'm confused. I thought that both were needed since a
combination of bank-width 16-bit / reg-io-width 32-bit is also
possible (in fact that is how I'm testing on my IGEPv2) and we have
talked about this before [1].
By reading both the OMAP3 TRM and the smsc LAN9221 data-sheet, it
seems that the reg-io-width is not about the data bus address width
but the CPU address width. The smsc data-sheet says:
"The simple, yet highly functional host bus interface provides a
glue-less connection to most common 16-bit microprocessors and
microcontrollers as well as 32-bit microprocessors with a 16-bit
external bus"
By looking at the smsc911x driver
(drivers/net/ethernet/smsc/smsc911x.c) I see that if you use
reg-io-width = <4> (SMSC911X_USE_32BIT) then the smsc911x hardware
registers can be read in one operation and if you use reg-io-width =
<2> (SMSC911X_USE_16BIT) then you need two operations to read the
register:
static inline u32 __smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg)
{
if (pdata->config.flags & SMSC911X_USE_32BIT)
return readl(pdata->ioaddr + reg);
if (pdata->config.flags & SMSC911X_USE_16BIT)
return ((readw(pdata->ioaddr + reg) & 0xFFFF) |
((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16));
BUG();
return 0;
}
Also, by reading at the OMAP3 TRM, I understand that even when the
GPMC has a maximum 16-bit address width, it support devices that has
32-bit registers by doing some sort of access adaptation.
So, as far as I understand the "bank-width" is to configure the GPMC
if is going to use a 8-bit or 16-bit width access and the
"reg-io-width" is how the smsc911x driver is going to read its
registers. So, I think we need both properties and there is no need to
change gpmc_probe_generic_child() neither pass the child name to it.
But to be honest I can be wrong here since data-sheet and technical
reference manuals can be quite confusing sometimes :-)
Thanks a lot for your feedback and best regards,
Javier
[1]: http://www.mail-archive.com/linux-omap@vger.kernel.org/msg85597.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
