When a UART transmitter is connected to (eg) a RS485 driver, it is
necessary to turn the driver on/off as quickly as possible. This is
best achieved in the serial driver itself (rather than in userspace
where the latency can be quite large).
This patch allows the GPIO pin to be defined (via DT) that controls
the enabling of the driver at the start of a message, and disables
the driver when the message has been completed.
Still to do:-
Allow userspace to turn this feature on/off
Do the same for the receiver (useful for 2 wire RS485)
Signed-off-by: Mark Jackson <m...@newflow.co.uk>
---
drivers/tty/serial/omap-serial.c | 57 ++++++++++++++++++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index b6d1728..1d3d117 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -40,9 +40,12 @@
#include <linux/pm_runtime.h>
#include <linux/of.h>
#include <linux/gpio.h>
+#include <linux/of_gpio.h>
#include <linux/pinctrl/consumer.h>
#include <linux/platform_data/serial-omap.h>
+#include <dt-bindings/gpio/gpio.h>
+
#define OMAP_MAX_HSUART_PORTS 6
#define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
@@ -156,6 +159,10 @@ struct uart_omap_port {
int DTR_inverted;
int DTR_active;
+ int txen_gpio;
+ int txen_inverted;
+ int txen_active;
+
struct pm_qos_request pm_qos_request;
u32 latency;
u32 calc_latency;
@@ -272,8 +279,25 @@ static void serial_omap_enable_ms(struct uart_port *port)
static void serial_omap_stop_tx(struct uart_port *port)
{
struct uart_omap_port *up = to_uart_omap_port(port);
+ struct circ_buf *xmit = &up->port.state->xmit;
pm_runtime_get_sync(up->dev);
+
+ // if txen currently active
+ if (up->txen_active) {
+ // do nothing if current tx not yet completed
+ int res = serial_in(up, UART_LSR) & UART_LSR_TEMT;
+ if (!res)
+ return;
+
+ // if there's no more data to send, turn off txen
+ if (uart_circ_empty(xmit)) {
+ gpio_set_value(up->txen_gpio,
+ up->txen_active ==
up->txen_inverted);
+ up->txen_active = 0;
+ }
+ }
+
if (up->ier & UART_IER_THRI) {
up->ier &= ~UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
@@ -300,6 +324,16 @@ static void transmit_chars(struct uart_omap_port *up,
unsigned int lsr)
struct circ_buf *xmit = &up->port.state->xmit;
int count;
+ // if txen in use
+ if (gpio_is_valid(up->txen_gpio)) {
+ // turn on txen ?
+ if (!uart_circ_empty(xmit) && (!up->txen_active)) {
+ gpio_set_value(up->txen_gpio,
+ up->txen_active == up->txen_inverted);
+ up->txen_active = 1;
+ }
+ }
+
if (up->port.x_char) {
serial_out(up, UART_TX, up->port.x_char);
up->port.icount.tx++;
@@ -1468,6 +1502,28 @@ static int serial_omap_probe(struct platform_device
*pdev)
goto err_port_line;
}
+ // init tx enable signal
+ up->txen_gpio = -EINVAL;
+ up->txen_inverted = 0;
+ up->txen_active = 0;
+ if (pdev->dev.of_node)
+ {
+ enum of_gpio_flags flags;
+ up->txen_gpio = of_get_named_gpio_flags(pdev->dev.of_node,
+ "txen-gpio", 0, &flags);
+ up->txen_inverted = (flags == GPIO_ACTIVE_LOW);
+ if (gpio_is_valid(up->txen_gpio)) {
+ ret = gpio_request(up->txen_gpio, "omap-serial");
+ if (ret < 0)
+ goto err_txen;
+ ret = gpio_direction_output(up->txen_gpio,
+ up->txen_inverted);
+ if (ret < 0)
+ goto err_txen;
+ } else
+ up->txen_gpio = -EINVAL;
+ }
+
up->pins = devm_pinctrl_get_select_default(&pdev->dev);
if (IS_ERR(up->pins)) {
dev_warn(&pdev->dev, "did not get pins for uart%i error: %li\n",
@@ -1529,6 +1585,7 @@ err_add_port:
pm_runtime_put(&pdev->dev);
pm_runtime_disable(&pdev->dev);
err_ioremap:
+err_txen:
err_port_line:
dev_err(&pdev->dev, "[UART%d]: failure [%s]: %d\n",
pdev->id, __func__, ret);
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
