Signed-off-by: Marek Belisko <ma...@goldelico.com>
Signed-off-by: H. Nikolaus Schaller <h...@goldelico.com>
---
changes from v2:
- move tx_buf from driver data to functions where it's used
- update write functions names (to reflect how many bytes are transferred)
- update delays from 1s to 1ms (probably typo)
- remove unnecessary 90ms sleep (tested and works fine)
- disable dpi output after disable panel
changes from v1:
- reworked to be spi driver instead platform with custom spi bitbang
this configuration was tested with spi_gpio bitbang driver on gta04 board
and works fine (thanks Tomi and Lars-Peter for comments)
- address previous comments
drivers/video/omap2/displays-new/Kconfig | 6 +
drivers/video/omap2/displays-new/Makefile | 1 +
.../omap2/displays-new/panel-tpo-td028ttec1.c | 480 +++++++++++++++++++++
include/video/omap-panel-data.h | 13 +
4 files changed, 500 insertions(+)
create mode 100644 drivers/video/omap2/displays-new/panel-tpo-td028ttec1.c
diff --git a/drivers/video/omap2/displays-new/Kconfig
b/drivers/video/omap2/displays-new/Kconfig
index 10b25e7..e6cfc38 100644
--- a/drivers/video/omap2/displays-new/Kconfig
+++ b/drivers/video/omap2/displays-new/Kconfig
@@ -57,6 +57,12 @@ config DISPLAY_PANEL_SHARP_LS037V7DW01
help
LCD Panel used in TI's SDP3430 and EVM boards
+config DISPLAY_PANEL_TPO_TD028TTEC1
+ tristate "TPO TD028TTEC1 LCD Panel"
+ depends on SPI
+ help
+ LCD panel used in Openmoko.
+
config DISPLAY_PANEL_TPO_TD043MTEA1
tristate "TPO TD043MTEA1 LCD Panel"
depends on SPI
diff --git a/drivers/video/omap2/displays-new/Makefile
b/drivers/video/omap2/displays-new/Makefile
index 5aeb11b..0323a8a 100644
--- a/drivers/video/omap2/displays-new/Makefile
+++ b/drivers/video/omap2/displays-new/Makefile
@@ -8,5 +8,6 @@ obj-$(CONFIG_DISPLAY_PANEL_DSI_CM) += panel-dsi-cm.o
obj-$(CONFIG_DISPLAY_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o
obj-$(CONFIG_DISPLAY_PANEL_LGPHILIPS_LB035Q02) += panel-lgphilips-lb035q02.o
obj-$(CONFIG_DISPLAY_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o
+obj-$(CONFIG_DISPLAY_PANEL_TPO_TD028TTEC1) += panel-tpo-td028ttec1.o
obj-$(CONFIG_DISPLAY_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o
obj-$(CONFIG_DISPLAY_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
diff --git a/drivers/video/omap2/displays-new/panel-tpo-td028ttec1.c
b/drivers/video/omap2/displays-new/panel-tpo-td028ttec1.c
new file mode 100644
index 0000000..ca77721
--- /dev/null
+++ b/drivers/video/omap2/displays-new/panel-tpo-td028ttec1.c
@@ -0,0 +1,480 @@
+/*
+ * Toppoly TD028TTEC1 panel support
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Author: Tomi Valkeinen <tomi.valkei...@nokia.com>
+ *
+ * Neo 1973 code (jbt6k74.c):
+ * Copyright (C) 2006-2007 by OpenMoko, Inc.
+ * Author: Harald Welte <lafo...@openmoko.org>
+ *
+ * Ported and adapted from Neo 1973 U-Boot by:
+ * H. Nikolaus Schaller <h...@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/spi/spi.h>
+#include <linux/gpio.h>
+#include <video/omapdss.h>
+#include <video/omap-panel-data.h>
+
+struct panel_drv_data {
+ struct omap_dss_device dssdev;
+ struct omap_dss_device *in;
+
+ int data_lines;
+
+ struct omap_video_timings videomode;
+
+ struct spi_device *spi_dev;
+};
+
+static struct omap_video_timings td028ttec1_panel_timings = {
+ .x_res = 480,
+ .y_res = 640,
+ .pixel_clock = 22153,
+ .hfp = 24,
+ .hsw = 8,
+ .hbp = 8,
+ .vfp = 4,
+ .vsw = 2,
+ .vbp = 2,
+
+ .vsync_level = OMAPDSS_SIG_ACTIVE_LOW,
+ .hsync_level = OMAPDSS_SIG_ACTIVE_LOW,
+
+ .data_pclk_edge = OMAPDSS_DRIVE_SIG_FALLING_EDGE,
+ .de_level = OMAPDSS_SIG_ACTIVE_HIGH,
+ .sync_pclk_edge = OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES,
+};
+
+#define JBT_COMMAND 0x000
+#define JBT_DATA 0x100
+
+int jbt_ret_write_0(struct panel_drv_data *ddata, u8 reg)
+{
+ int rc;
+ u16 tx_buf = JBT_COMMAND | reg;
+
+ rc = spi_write(ddata->spi_dev, (u8 *)&tx_buf,
+ 1*sizeof(u16));
+ if (rc != 0)
+ dev_err(&ddata->spi_dev->dev,
+ "jbt_ret_write_0 spi_write ret %d\n", rc);
+
+ return rc;
+}
+
+int jbt_reg_write_1(struct panel_drv_data *ddata, u8 reg, u8 data)
+{
+ int rc;
+ u16 tx_buf[2];
+
+ tx_buf[0] = JBT_COMMAND | reg;
+ tx_buf[1] = JBT_DATA | data;
+ rc = spi_write(ddata->spi_dev, (u8 *)tx_buf,
+ 2*sizeof(u16));
+ if (rc != 0)
+ dev_err(&ddata->spi_dev->dev,
+ "jbt_reg_write_1 spi_write ret %d\n", rc);
+
+ return rc;
+}
+
+int jbt_reg_write_2(struct panel_drv_data *ddata, u8 reg, u16 data)
+{
+ int rc;
+ u16 tx_buf[3];
+
+ tx_buf[0] = JBT_COMMAND | reg;
+ tx_buf[1] = JBT_DATA | (data >> 8);
+ tx_buf[2] = JBT_DATA | (data & 0xff);
+
+ rc = spi_write(ddata->spi_dev, (u8 *)tx_buf,
+ 3*sizeof(u16));
+
+ if (rc != 0)
+ dev_err(&ddata->spi_dev->dev,
+ "jbt_reg_write_2 spi_write ret %d\n", rc);
+
+ return rc;
+}
+
+enum jbt_register {
+ JBT_REG_SLEEP_IN = 0x10,
+ JBT_REG_SLEEP_OUT = 0x11,
+
+ JBT_REG_DISPLAY_OFF = 0x28,
+ JBT_REG_DISPLAY_ON = 0x29,
+
+ JBT_REG_RGB_FORMAT = 0x3a,
+ JBT_REG_QUAD_RATE = 0x3b,
+
+ JBT_REG_POWER_ON_OFF = 0xb0,
+ JBT_REG_BOOSTER_OP = 0xb1,
+ JBT_REG_BOOSTER_MODE = 0xb2,
+ JBT_REG_BOOSTER_FREQ = 0xb3,
+ JBT_REG_OPAMP_SYSCLK = 0xb4,
+ JBT_REG_VSC_VOLTAGE = 0xb5,
+ JBT_REG_VCOM_VOLTAGE = 0xb6,
+ JBT_REG_EXT_DISPL = 0xb7,
+ JBT_REG_OUTPUT_CONTROL = 0xb8,
+ JBT_REG_DCCLK_DCEV = 0xb9,
+ JBT_REG_DISPLAY_MODE1 = 0xba,
+ JBT_REG_DISPLAY_MODE2 = 0xbb,
+ JBT_REG_DISPLAY_MODE = 0xbc,
+ JBT_REG_ASW_SLEW = 0xbd,
+ JBT_REG_DUMMY_DISPLAY = 0xbe,
+ JBT_REG_DRIVE_SYSTEM = 0xbf,
+
+ JBT_REG_SLEEP_OUT_FR_A = 0xc0,
+ JBT_REG_SLEEP_OUT_FR_B = 0xc1,
+ JBT_REG_SLEEP_OUT_FR_C = 0xc2,
+ JBT_REG_SLEEP_IN_LCCNT_D = 0xc3,
+ JBT_REG_SLEEP_IN_LCCNT_E = 0xc4,
+ JBT_REG_SLEEP_IN_LCCNT_F = 0xc5,
+ JBT_REG_SLEEP_IN_LCCNT_G = 0xc6,
+
+ JBT_REG_GAMMA1_FINE_1 = 0xc7,
+ JBT_REG_GAMMA1_FINE_2 = 0xc8,
+ JBT_REG_GAMMA1_INCLINATION = 0xc9,
+ JBT_REG_GAMMA1_BLUE_OFFSET = 0xca,
+
+ JBT_REG_BLANK_CONTROL = 0xcf,
+ JBT_REG_BLANK_TH_TV = 0xd0,
+ JBT_REG_CKV_ON_OFF = 0xd1,
+ JBT_REG_CKV_1_2 = 0xd2,
+ JBT_REG_OEV_TIMING = 0xd3,
+ JBT_REG_ASW_TIMING_1 = 0xd4,
+ JBT_REG_ASW_TIMING_2 = 0xd5,
+
+ JBT_REG_HCLOCK_VGA = 0xec,
+ JBT_REG_HCLOCK_QVGA = 0xed,
+};
+
+#define to_panel_data(p) container_of(p, struct panel_drv_data, dssdev)
+
+static int td028ttec1_panel_connect(struct omap_dss_device *dssdev)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+ struct omap_dss_device *in = ddata->in;
+ int r;
+
+ if (omapdss_device_is_connected(dssdev))
+ return 0;
+
+ r = in->ops.dpi->connect(in, dssdev);
+ if (r)
+ return r;
+
+ return 0;
+}
+
+static void td028ttec1_panel_disconnect(struct omap_dss_device *dssdev)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+ struct omap_dss_device *in = ddata->in;
+
+ if (!omapdss_device_is_connected(dssdev))
+ return;
+
+ in->ops.dpi->disconnect(in, dssdev);
+}
+
+static int td028ttec1_panel_enable(struct omap_dss_device *dssdev)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+ struct omap_dss_device *in = ddata->in;
+ int r;
+
+ if (!omapdss_device_is_connected(dssdev))
+ return -ENODEV;
+
+ if (omapdss_device_is_enabled(dssdev))
+ return 0;
+
+ in->ops.dpi->set_data_lines(in, ddata->data_lines);
+ in->ops.dpi->set_timings(in, &ddata->videomode);
+
+ r = in->ops.dpi->enable(in);
+ if (r)
+ return r;
+
+ dev_dbg(dssdev->dev, "td028ttec1_panel_enable() - state %d\n",
+ dssdev->state);
+
+ /* three times command zero */
+ r |= jbt_ret_write_0(ddata, 0x00);
+ usleep_range(1000, 2000);
+ r |= jbt_ret_write_0(ddata, 0x00);
+ usleep_range(1000, 2000);
+ r |= jbt_ret_write_0(ddata, 0x00);
+ usleep_range(1000, 2000);
+
+ if (r) {
+ dev_warn(dssdev->dev, "transfer error\n");
+ goto transfer_err;
+ }
+
+ /* deep standby out */
+ r |= jbt_reg_write_1(ddata, JBT_REG_POWER_ON_OFF, 0x17);
+
+ /* RGB I/F on, RAM write off, QVGA through, SIGCON enable */
+ r |= jbt_reg_write_1(ddata, JBT_REG_DISPLAY_MODE, 0x80);
+
+ /* Quad mode off */
+ r |= jbt_reg_write_1(ddata, JBT_REG_QUAD_RATE, 0x00);
+
+ /* AVDD on, XVDD on */
+ r |= jbt_reg_write_1(ddata, JBT_REG_POWER_ON_OFF, 0x16);
+
+ /* Output control */
+ r |= jbt_reg_write_2(ddata, JBT_REG_OUTPUT_CONTROL, 0xfff9);
+
+ /* Sleep mode off */
+ r |= jbt_ret_write_0(ddata, JBT_REG_SLEEP_OUT);
+
+ /* at this point we have like 50% grey */
+
+ /* initialize register set */
+ r |= jbt_reg_write_1(ddata, JBT_REG_DISPLAY_MODE1, 0x01);
+ r |= jbt_reg_write_1(ddata, JBT_REG_DISPLAY_MODE2, 0x00);
+ r |= jbt_reg_write_1(ddata, JBT_REG_RGB_FORMAT, 0x60);
+ r |= jbt_reg_write_1(ddata, JBT_REG_DRIVE_SYSTEM, 0x10);
+ r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_OP, 0x56);
+ r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_MODE, 0x33);
+ r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_FREQ, 0x11);
+ r |= jbt_reg_write_1(ddata, JBT_REG_BOOSTER_FREQ, 0x11);
+ r |= jbt_reg_write_1(ddata, JBT_REG_OPAMP_SYSCLK, 0x02);
+ r |= jbt_reg_write_1(ddata, JBT_REG_VSC_VOLTAGE, 0x2b);
+ r |= jbt_reg_write_1(ddata, JBT_REG_VCOM_VOLTAGE, 0x40);
+ r |= jbt_reg_write_1(ddata, JBT_REG_EXT_DISPL, 0x03);
+ r |= jbt_reg_write_1(ddata, JBT_REG_DCCLK_DCEV, 0x04);
+ /*
+ * default of 0x02 in JBT_REG_ASW_SLEW responsible for 72Hz requirement
+ * to avoid red / blue flicker
+ */
+ r |= jbt_reg_write_1(ddata, JBT_REG_ASW_SLEW, 0x04);
+ r |= jbt_reg_write_1(ddata, JBT_REG_DUMMY_DISPLAY, 0x00);
+
+ r |= jbt_reg_write_1(ddata, JBT_REG_SLEEP_OUT_FR_A, 0x11);
+ r |= jbt_reg_write_1(ddata, JBT_REG_SLEEP_OUT_FR_B, 0x11);
+ r |= jbt_reg_write_1(ddata, JBT_REG_SLEEP_OUT_FR_C, 0x11);
+ r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_D, 0x2040);
+ r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_E, 0x60c0);
+ r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_F, 0x1020);
+ r |= jbt_reg_write_2(ddata, JBT_REG_SLEEP_IN_LCCNT_G, 0x60c0);
+
+ r |= jbt_reg_write_2(ddata, JBT_REG_GAMMA1_FINE_1, 0x5533);
+ r |= jbt_reg_write_1(ddata, JBT_REG_GAMMA1_FINE_2, 0x00);
+ r |= jbt_reg_write_1(ddata, JBT_REG_GAMMA1_INCLINATION, 0x00);
+ r |= jbt_reg_write_1(ddata, JBT_REG_GAMMA1_BLUE_OFFSET, 0x00);
+
+ r |= jbt_reg_write_2(ddata, JBT_REG_HCLOCK_VGA, 0x1f0);
+ r |= jbt_reg_write_1(ddata, JBT_REG_BLANK_CONTROL, 0x02);
+ r |= jbt_reg_write_2(ddata, JBT_REG_BLANK_TH_TV, 0x0804);
+
+ r |= jbt_reg_write_1(ddata, JBT_REG_CKV_ON_OFF, 0x01);
+ r |= jbt_reg_write_2(ddata, JBT_REG_CKV_1_2, 0x0000);
+
+ r |= jbt_reg_write_2(ddata, JBT_REG_OEV_TIMING, 0x0d0e);
+ r |= jbt_reg_write_2(ddata, JBT_REG_ASW_TIMING_1, 0x11a4);
+ r |= jbt_reg_write_1(ddata, JBT_REG_ASW_TIMING_2, 0x0e);
+
+ r |= jbt_ret_write_0(ddata, JBT_REG_DISPLAY_ON);
+
+ dssdev->state = OMAP_DSS_DISPLAY_ACTIVE;
+
+transfer_err:
+
+ return r ? -EIO : 0;
+}
+
+static void td028ttec1_panel_disable(struct omap_dss_device *dssdev)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+ struct omap_dss_device *in = ddata->in;
+
+ if (!omapdss_device_is_enabled(dssdev))
+ return;
+
+ dev_dbg(dssdev->dev, "td028ttec1_panel_disable()\n");
+
+ jbt_ret_write_0(ddata, JBT_REG_DISPLAY_OFF);
+ jbt_reg_write_2(ddata, JBT_REG_OUTPUT_CONTROL, 0x8002);
+ jbt_ret_write_0(ddata, JBT_REG_SLEEP_IN);
+ jbt_reg_write_1(ddata, JBT_REG_POWER_ON_OFF, 0x00);
+
+ in->ops.dpi->disable(in);
+
+ dssdev->state = OMAP_DSS_DISPLAY_DISABLED;
+}
+
+static void td028ttec1_panel_set_timings(struct omap_dss_device *dssdev,
+ struct omap_video_timings *timings)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+ struct omap_dss_device *in = ddata->in;
+
+ ddata->videomode = *timings;
+ dssdev->panel.timings = *timings;
+
+ in->ops.dpi->set_timings(in, timings);
+}
+
+static void td028ttec1_panel_get_timings(struct omap_dss_device *dssdev,
+ struct omap_video_timings *timings)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+
+ *timings = ddata->videomode;
+}
+
+static int td028ttec1_panel_check_timings(struct omap_dss_device *dssdev,
+ struct omap_video_timings *timings)
+{
+ struct panel_drv_data *ddata = to_panel_data(dssdev);
+ struct omap_dss_device *in = ddata->in;
+
+ return in->ops.dpi->check_timings(in, timings);
+}
+
+static struct omap_dss_driver td028ttec1_ops = {
+ .connect = td028ttec1_panel_connect,
+ .disconnect = td028ttec1_panel_disconnect,
+
+ .enable = td028ttec1_panel_enable,
+ .disable = td028ttec1_panel_disable,
+
+ .set_timings = td028ttec1_panel_set_timings,
+ .get_timings = td028ttec1_panel_get_timings,
+ .check_timings = td028ttec1_panel_check_timings,
+};
+
+static int td028ttec1_panel_probe_pdata(struct spi_device *spi)
+{
+ const struct panel_tpo_td028ttec1_platform_data *pdata;
+ struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev);
+ struct omap_dss_device *dssdev, *in;
+
+ pdata = dev_get_platdata(&spi->dev);
+
+ in = omap_dss_find_output(pdata->source);
+ if (in == NULL) {
+ dev_err(&spi->dev, "failed to find video source '%s'\n",
+ pdata->source);
+ return -EPROBE_DEFER;
+ }
+
+ ddata->in = in;
+
+ ddata->data_lines = pdata->data_lines;
+
+ dssdev = &ddata->dssdev;
+ dssdev->name = pdata->name;
+
+ return 0;
+}
+
+static int td028ttec1_panel_probe(struct spi_device *spi)
+{
+ struct panel_drv_data *ddata;
+ struct omap_dss_device *dssdev;
+ int r;
+
+ dev_dbg(&spi->dev, "%s\n", __func__);
+
+ spi->bits_per_word = 9;
+ spi->mode = SPI_MODE_3;
+
+ r = spi_setup(spi);
+ if (r < 0) {
+ dev_err(&spi->dev, "spi_setup failed: %d\n", r);
+ return r;
+ }
+
+ ddata = devm_kzalloc(&spi->dev, sizeof(*ddata), GFP_KERNEL);
+ if (ddata == NULL)
+ return -ENOMEM;
+
+ dev_set_drvdata(&spi->dev, ddata);
+
+ ddata->spi_dev = spi;
+
+ if (dev_get_platdata(&spi->dev)) {
+ r = td028ttec1_panel_probe_pdata(spi);
+ if (r)
+ return r;
+ } else {
+ return -ENODEV;
+ }
+
+ ddata->videomode = td028ttec1_panel_timings;
+
+ dssdev = &ddata->dssdev;
+ dssdev->dev = &spi->dev;
+ dssdev->driver = &td028ttec1_ops;
+ dssdev->type = OMAP_DISPLAY_TYPE_DPI;
+ dssdev->owner = THIS_MODULE;
+ dssdev->panel.timings = ddata->videomode;
+ dssdev->phy.dpi.data_lines = ddata->data_lines;
+
+ r = omapdss_register_display(dssdev);
+ if (r) {
+ dev_err(&spi->dev, "Failed to register panel\n");
+ goto err_reg;
+ }
+
+ return 0;
+
+err_reg:
+ omap_dss_put_device(ddata->in);
+ return r;
+}
+
+static int td028ttec1_panel_remove(struct spi_device *spi)
+{
+ struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev);
+ struct omap_dss_device *dssdev = &ddata->dssdev;
+ struct omap_dss_device *in = ddata->in;
+
+ dev_dbg(&ddata->spi_dev->dev, "%s\n", __func__);
+
+ omapdss_unregister_display(dssdev);
+
+ td028ttec1_panel_disable(dssdev);
+ td028ttec1_panel_disconnect(dssdev);
+
+ omap_dss_put_device(in);
+
+ return 0;
+}
+
+static struct spi_driver td028ttec1_spi_driver = {
+ .probe = td028ttec1_panel_probe,
+ .remove = td028ttec1_panel_remove,
+
+ .driver = {
+ .name = "panel-tpo-td028ttec1",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_spi_driver(td028ttec1_spi_driver);
+
+MODULE_AUTHOR("H. Nikolaus Schaller <h...@goldelico.com>");
+MODULE_DESCRIPTION("Toppoly TD028TTEC1 panel driver");
+MODULE_LICENSE("GPL");
diff --git a/include/video/omap-panel-data.h b/include/video/omap-panel-data.h
index f7ac8d9..69279c0 100644
--- a/include/video/omap-panel-data.h
+++ b/include/video/omap-panel-data.h
@@ -238,4 +238,17 @@ struct panel_nec_nl8048hl11_platform_data {
int qvga_gpio;
};
+/**
+ * panel-tpo-td028ttec1 platform data
+ * @name: name for display entity
+ * @source: name of the display entity used as a video source
+ * @data_lines: number of DPI datalines
+ */
+struct panel_tpo_td028ttec1_platform_data {
+ const char *name;
+ const char *source;
+
+ int data_lines;
+};
+
#endif /* __OMAP_PANEL_DATA_H */
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
