Add a helper to get the voltage state of CF sockets, where the voltage
sense pins are not wired up. Switch assabet and cerf to use this
helper.
Signed-off-by: Russell King <rmk+ker...@armlinux.org.uk>
---
drivers/pcmcia/sa1100_assabet.c | 9 +--------
drivers/pcmcia/sa1100_cerf.c | 9 +--------
drivers/pcmcia/soc_common.c | 12 ++++++++++++
drivers/pcmcia/soc_common.h | 2 ++
4 files changed, 16 insertions(+), 16 deletions(-)
diff --git a/drivers/pcmcia/sa1100_assabet.c b/drivers/pcmcia/sa1100_assabet.c
index 44cfc4416e54..71ace6910d7e 100644
--- a/drivers/pcmcia/sa1100_assabet.c
+++ b/drivers/pcmcia/sa1100_assabet.c
@@ -31,13 +31,6 @@ static int assabet_pcmcia_hw_init(struct soc_pcmcia_socket
*skt)
return 0;
}
-static void
-assabet_pcmcia_socket_state(struct soc_pcmcia_socket *skt, struct pcmcia_state
*state)
-{
- state->vs_3v = 1; /* Can only apply 3.3V on Assabet. */
- state->vs_Xv = 0;
-}
-
static int
assabet_pcmcia_configure_socket(struct soc_pcmcia_socket *skt, const
socket_state_t *state)
{
@@ -90,7 +83,7 @@ static void assabet_pcmcia_socket_suspend(struct
soc_pcmcia_socket *skt)
static struct pcmcia_low_level assabet_pcmcia_ops = {
.owner = THIS_MODULE,
.hw_init = assabet_pcmcia_hw_init,
- .socket_state = assabet_pcmcia_socket_state,
+ .socket_state = soc_common_cf_socket_state,
.configure_socket = assabet_pcmcia_configure_socket,
.socket_suspend = assabet_pcmcia_socket_suspend,
};
diff --git a/drivers/pcmcia/sa1100_cerf.c b/drivers/pcmcia/sa1100_cerf.c
index b3774e5d0396..c3f67363f6a1 100644
--- a/drivers/pcmcia/sa1100_cerf.c
+++ b/drivers/pcmcia/sa1100_cerf.c
@@ -45,13 +45,6 @@ static void cerf_pcmcia_hw_shutdown(struct soc_pcmcia_socket
*skt)
gpio_free(CERF_GPIO_CF_RESET);
}
-static void
-cerf_pcmcia_socket_state(struct soc_pcmcia_socket *skt, struct pcmcia_state
*state)
-{
- state->vs_3v = 1;
- state->vs_Xv = 0;
-}
-
static int
cerf_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
const socket_state_t *state)
@@ -77,7 +70,7 @@ static struct pcmcia_low_level cerf_pcmcia_ops = {
.owner = THIS_MODULE,
.hw_init = cerf_pcmcia_hw_init,
.hw_shutdown = cerf_pcmcia_hw_shutdown,
- .socket_state = cerf_pcmcia_socket_state,
+ .socket_state = soc_common_cf_socket_state,
.configure_socket = cerf_pcmcia_configure_socket,
};
diff --git a/drivers/pcmcia/soc_common.c b/drivers/pcmcia/soc_common.c
index d8508c41d7da..f880f805c2ca 100644
--- a/drivers/pcmcia/soc_common.c
+++ b/drivers/pcmcia/soc_common.c
@@ -235,6 +235,18 @@ static void soc_pcmcia_hw_disable(struct soc_pcmcia_socket
*skt)
irq_set_irq_type(skt->stat[i].irq, IRQ_TYPE_NONE);
}
+/*
+ * The CF 3.0 specification says that cards tie VS1 to ground and leave
+ * VS2 open. Many implementations do not wire up the VS signals, so we
+ * provide hard-coded values as per the CF 3.0 spec.
+ */
+void soc_common_cf_socket_state(struct soc_pcmcia_socket *skt,
+ struct pcmcia_state *state)
+{
+ state->vs_3v = 1;
+}
+EXPORT_SYMBOL_GPL(soc_common_cf_socket_state);
+
static unsigned int soc_common_pcmcia_skt_state(struct soc_pcmcia_socket *skt)
{
struct pcmcia_state state;
diff --git a/drivers/pcmcia/soc_common.h b/drivers/pcmcia/soc_common.h
index 686ba3238c76..39c1e15167f3 100644
--- a/drivers/pcmcia/soc_common.h
+++ b/drivers/pcmcia/soc_common.h
@@ -143,6 +143,8 @@ void soc_pcmcia_remove_one(struct soc_pcmcia_socket *skt);
int soc_pcmcia_add_one(struct soc_pcmcia_socket *skt);
int soc_pcmcia_request_gpiods(struct soc_pcmcia_socket *skt);
+void soc_common_cf_socket_state(struct soc_pcmcia_socket *skt,
+ struct pcmcia_state *state);
#ifdef CONFIG_PCMCIA_DEBUG
--
2.1.0
_______________________________________________
Linux PCMCIA reimplementation list
http://lists.infradead.org/mailman/listinfo/linux-pcmcia
