On 02/18/2016 02:48 AM, Simon Horman wrote:
Define the generic R8A7794 part of the sound device node.
This sound device is a complex one and comprises the Audio Clock Generator
(ADG), Sampling Rate Converter Unit (SCU), Serial Sound Interface [Unit]
(SSI[U]), and Audio DMAC-Peripheral-Peripheral.
It is up to the board file to enable the device.
This patch is based on the R8A7791 sound work by Kuninori Morimoto.
Signed-off-by: Sergei Shtylyov <sergei.shtyl...@cogentembedded.com>
(snip)
+ rcar_sound,src {
+ src1: src@1 {
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&audma0 0x87>, <&audma0 0x9c>;
+ dma-names = "rx", "tx";
+ };
+ src2: src@2 {
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&audma0 0x89>, <&audma0 0x9e>;
+ dma-names = "rx", "tx";
+ };
+ src3: src@3 {
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&audma0 0x8b>, <&audma0 0xa0>;
+ dma-names = "rx", "tx";
+ };
+ src4: src@4 {
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&audma0 0x8d>, <&audma0 0xb0>;
+ dma-names = "rx", "tx";
+ };
+ src5: src@5 {
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&audma0 0x8f>, <&audma0 0xb2>;
+ dma-names = "rx", "tx";
+ };
+ src6: src@6 {
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&audma0 0x91>, <&audma0 0xb4>;
+ dma-names = "rx", "tx";
+ };
+ };
I think this can't work correctly, because driver is assuming
DT has all channles (from 0). (see linux/sound/soc/sh/rcar/src.c ::
rsnd_src_probe)
Can you adds dummy src0 with some comments ? or fix src.c driver ?
I would prefer the driver to be fixed (I had a similar patchset locally
and I found it doesn't work).
You mean you had R8A7794 sound patch set too?
Yes, I was working on it recently.
I suppose we should coordinate these things in future to avoid
duplicated effort.
Yes, seems a good idea now. :-)
The reason is that DT should describe
the hardware rather than the current state of the software.
Yes, of course. Just tell me do I have to fix the driver *before* this
patch set is accepted?
I did not entirely get to the bottom of the problem, but I think that at
the very least something needs to be done about the for_each_rsnd_src()
loop in rsnd_src_probe.
It's not that it replies to my question. :-)
So you're looking at this issue yourself?
I have not got very far, as you can see, but I was planning to look into it.
I don't mind if you want to do so.
After consultation with the management, I'm going to look into this issue
myself. :-)
Excellent.
But not immediately. I have some other things to look at before that (DU
and AVB), they'll going to take some (significant) time... :-(
FWIW, I can test anything you come up with for the r8a7794 an alt board
I have remote access to Alt now, in fact using it currently for the AVB
work.
or post patches for it once you have r8a7794/silk sorted out.
I already have audio on these working. Or you're going to wait until I
fix the SRC issue?
I'm happy to merge a subset of your r8a7794/silk patches,
that don't touch the SRC issue if you think that is appropriate.
I think you can merge everything R8A7794 specific. The SILK patch doesn't
make use of SRCs yet but depends on the PFC patches, so makes sense to hold it
up...
From there I could get similar functionality running on the Alt - I don't
expect that to be a difficult task.
Sure -- if you have direct access to the board.
And then when you come back to the SRC
issue we can enhance support for r8a7794/silk,alt.
Yes.
MBR, Sergei