Hi Magnus,
On Thu, Mar 23, 2017 at 9:30 AM, Magnus Damm <magnus.d...@gmail.com> wrote:
> On Tue, Mar 21, 2017 at 6:30 PM, Geert Uytterhoeven
> <ge...@linux-m68k.org> wrote:
>> On Tue, Mar 21, 2017 at 8:17 AM, Magnus Damm <magnus.d...@gmail.com> wrote:
>>> On Mon, Mar 20, 2017 at 7:57 PM, Geert Uytterhoeven
>>> <ge...@linux-m68k.org> wrote:
>>>> On Mon, Mar 20, 2017 at 9:49 AM, Magnus Damm <magnus.d...@gmail.com> wrote:
>>>>> --- 0001/arch/arm64/boot/dts/renesas/r8a7795.dtsi
>>>>> +++ work/arch/arm64/boot/dts/renesas/r8a7795.dtsi 2017-03-20
>>>>> 17:41:36.390607110 +0900
>>>>> @@ -1209,7 +1209,7 @@
>>>>>
>>>>> sata: sata@ee300000 {
>>>>> compatible = "renesas,sata-r8a7795";
>>>>> - reg = <0 0xee300000 0 0x1fff>;
>>>>> + reg = <0 0xee300000 0 0x200000>;
>>>>
>>>> While the datasheet does mention the 2 MiB area, it also says no (write)
>>>> access should be made to registers not listed in the table, while these are
>>>> all covered by the existing area?
>>>
>>> That bit about not writing to non-listed registers seems like just
>>> common sense to me, but perhaps there is more to the story than just
>>
>> Sure.
>>
>>> that? Like you say it is probably possible to use the driver with the
>>> existing 8K-1 size, but in my mind we should use window sizes defined
>>> in the data sheet for DT?
>>
>> The 2 MiB window size is a lot larger than needed to cover all documented
>> rregisters. Either there are more undocumented registers, or the hardware
>> engineers were lazy and just decoded the full 2 MiB block.
>
> Yeah, and on top of that it looks to me like the size is not aligned
> to the offset either. I would expect a 2MiB block to be aligned to a
> 2MiB boundary...
The base address was aligned to 2 miB on R-Car H1.
As of R-Car Gen2, it's no longer aligned. Too much copy-'n-paste...
>>>> BTW, what about the Reference Clock Source Select Register, which lies
>>>> in a further undocumented area?
>>>
>>> Yeah, no idea. This would be good task for the I/O or Core group to
>>
>> SATA is I/O.
>
> For sure, however I wonder how the external clock register REFSEL is
> supposed to be handled. It looks like an external hardware block
> somehow.
It's a single bit to select between internal and external clock.
No documention about which external clock.
>>> figure out how to handle. I'm surprised that the SATA DT device nodes
>>> with the strange and incorrect 0x1fff size got merged upstream without
>>> anyone thinking about that register that you are mentioning. Seems
>>> like supporting that should be part of SATA development for R-Car
>>> Gen3?
>>
>> Probably it was just an oversight. I almost missed it myself when
>> reviewing your patch.
>
> Probably yes.
It was up-ported from a patch in the BSP, which may predate the datasheet
revision that documented REFSEL.
>> The register is not present (not documented) on R-Car H1 and Gen2.
>> The IP core is derived from SH-Navi2G (sh7775), but no datasheet.
>
> On R-Car Gen3 there seem to be a chance that random glue hardware for
> other devices may also be present in the 0xe65exxxx range however
> documentations seem to be lacking...
And without documentation...
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- ge...@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
