From: Phil Edworthy <phil.edwor...@renesas.com> Most PCIe host controllers support L0s and L1 power states via ASPM. The R-Car hardware only supports L0s, so when the system suspends and resumes we have to manually handle L1.
When the system suspends, cards can put themselves into L1 and send a PM_ENTER_L1 DLLP to the host controller. At this point, we can no longer access the card's config registers. The R-Car host controller will handle taking cards out of L1 as long as the host controller has also been transitioned to L1 link state. Ideally, we would detect the PM_ENTER_L1 DLLP using an interrupt and transition the host to L1 immediately. However, this patch just ensures that we can talk to cards after they have gone into L1. When attempting a config access, it checks to see if the card has gone into L1, and if so, does the same for the host controller. This is based on a patch by Hien Dang <hien.dang...@rvc.renesas.com> Signed-off-by: Phil Edworthy <phil.edwor...@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+rene...@gmail.com> Cc: Geert Uytterhoeven <geert+rene...@glider.be> Cc: Simon Horman <horms+rene...@verge.net.au> Cc: Wolfram Sang <w...@the-dreams.de> Cc: linux-renesas-soc@vger.kernel.org --- drivers/pci/host/pcie-rcar.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/drivers/pci/host/pcie-rcar.c b/drivers/pci/host/pcie-rcar.c index aa588a7d4811..2b28292de93a 100644 --- a/drivers/pci/host/pcie-rcar.c +++ b/drivers/pci/host/pcie-rcar.c @@ -92,6 +92,13 @@ #define MACCTLR 0x011058 #define SPEED_CHANGE (1 << 24) #define SCRAMBLE_DISABLE (1 << 27) +#define PMSR 0x01105c +#define L1FAEG (1 << 31) +#define PM_ENTER_L1RX (1 << 23) +#define PMSTATE (7 << 16) +#define PMSTATE_L1 (3 << 16) +#define PMCTLR 0x011060 +#define L1_INIT (1 << 31) #define MACS2R 0x011078 #define MACCGSPSETR 0x011084 #define SPCNGRSN (1 << 31) @@ -191,6 +198,7 @@ static int rcar_pcie_config_access(struct rcar_pcie *pcie, unsigned int devfn, int where, u32 *data) { int dev, func, reg, index; + u32 val; dev = PCI_SLOT(devfn); func = PCI_FUNC(devfn); @@ -232,6 +240,22 @@ static int rcar_pcie_config_access(struct rcar_pcie *pcie, if (pcie->root_bus_nr < 0) return PCIBIOS_DEVICE_NOT_FOUND; + /* + * If we are not in L1 link state and we have received PM_ENTER_L1 DLLP, + * transition to L1 link state. The HW will handle coming of of L1. + */ + val = rcar_pci_read_reg(pcie, PMSR); + if ((val & PM_ENTER_L1RX) && ((val & PMSTATE) != PMSTATE_L1)) { + rcar_pci_write_reg(pcie, L1_INIT, PMCTLR); + + /* Wait until we are in L1 */ + while (!(val & L1FAEG)) + val = rcar_pci_read_reg(pcie, PMSR); + + /* Clear flags indicating link has transitioned to L1 */ + rcar_pci_write_reg(pcie, L1FAEG | PM_ENTER_L1RX, PMSR); + } + /* Clear errors */ rcar_pci_write_reg(pcie, rcar_pci_read_reg(pcie, PCIEERRFR), PCIEERRFR); -- 2.11.0