Hi Jacopo, Thanks for your feedback.
On 2018-05-14 15:14:48 +0200, Jacopo Mondi wrote: > Hi Niklas, > thanks for the patch > > On Sun, May 13, 2018 at 09:19:17PM +0200, Niklas Söderlund wrote: > > A V4L2 driver for Renesas R-Car MIPI CSI-2 receiver. The driver > > supports the R-Car Gen3 SoCs where separate CSI-2 hardware blocks are > > connected between the video sources and the video grabbers (VIN). > > > > Driver is based on a prototype by Koji Matsuoka in the Renesas BSP. > > > > Signed-off-by: Niklas Söderlund <niklas.soderlund+rene...@ragnatech.se> > > > > --- > > > > * Changes since v14 > > - Data sheet update changed init sequence for PHY forcing a restructure > > of the driver. The restructure was so big I felt compel to drop all > > review tags :-( > > - The change was that the Renesas H3 procedure was aligned with other > > SoC in the Gen3 family procedure. I had kept the rework as separate > > patches and was planing to post once original driver with H3 and M3-W > > support where merged. As review tags are dropped I chosen to squash > > those patches into 2/2. > > - Add support for Gen3 V3M. > > - Add support for Gen3 M3-N. > > - Set PHTC_TESTCLR when stopping the PHY. > > - Revert back to the v12 and earlier phypll calculation as it turns out > > it was correct after all. > > > > * Changes since v13 > > - Change return rcar_csi2_formats + i to return &rcar_csi2_formats[i]. > > - Add define for PHCLM_STOPSTATECKL. > > - Update spelling in comments. > > - Update calculation in rcar_csi2_calc_phypll() according to > > https://linuxtv.org/downloads/v4l-dvb-apis/kapi/csi2.html. The one > > before v14 did not take into account that 2 bits per sample is > > transmitted. > > - Use Geert's suggestion of (1 << priv->lanes) - 1 instead of switch > > statement to set correct number of lanes to enable. > > - Change hex constants in hsfreqrange_m3w_h3es1[] to lower case to match > > style of rest of file. > > - Switch to %u instead of 0x%x when printing bus type. > > - Switch to %u instead of %d for priv->lanes which is unsigned. > > - Add MEDIA_BUS_FMT_YUYV8_1X16 to the list of supported formats in > > rcar_csi2_formats[]. > > - Fixed bps for MEDIA_BUS_FMT_YUYV10_2X10 to 20 and not 16. > > - Set INTSTATE after PL-11 is confirmed to match flow chart in > > datasheet. > > - Change priv->notifier.subdevs == NULL to !priv->notifier.subdevs. > > - Add Maxime's and laurent's tags. > > --- > > drivers/media/platform/rcar-vin/Kconfig | 12 + > > drivers/media/platform/rcar-vin/Makefile | 1 + > > drivers/media/platform/rcar-vin/rcar-csi2.c | 1101 +++++++++++++++++++ > > 3 files changed, 1114 insertions(+) > > create mode 100644 drivers/media/platform/rcar-vin/rcar-csi2.c > > > > diff --git a/drivers/media/platform/rcar-vin/Kconfig > > b/drivers/media/platform/rcar-vin/Kconfig > > index 8fa7ee468c63afb9..d5835da6d4100d87 100644 > > --- a/drivers/media/platform/rcar-vin/Kconfig > > +++ b/drivers/media/platform/rcar-vin/Kconfig > > @@ -1,3 +1,15 @@ > > +config VIDEO_RCAR_CSI2 > > + tristate "R-Car MIPI CSI-2 Receiver" > > + depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF > > + depends on ARCH_RENESAS || COMPILE_TEST > > + select V4L2_FWNODE > > + help > > + Support for Renesas R-Car MIPI CSI-2 receiver. > > + Supports R-Car Gen3 SoCs. > > + > > + To compile this driver as a module, choose M here: the > > + module will be called rcar-csi2. > > + > > config VIDEO_RCAR_VIN > > tristate "R-Car Video Input (VIN) Driver" > > depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF && HAS_DMA && > > MEDIA_CONTROLLER > > diff --git a/drivers/media/platform/rcar-vin/Makefile > > b/drivers/media/platform/rcar-vin/Makefile > > index 48c5632c21dc060b..5ab803d3e7c1aa57 100644 > > --- a/drivers/media/platform/rcar-vin/Makefile > > +++ b/drivers/media/platform/rcar-vin/Makefile > > @@ -1,3 +1,4 @@ > > rcar-vin-objs = rcar-core.o rcar-dma.o rcar-v4l2.o > > > > +obj-$(CONFIG_VIDEO_RCAR_CSI2) += rcar-csi2.o > > obj-$(CONFIG_VIDEO_RCAR_VIN) += rcar-vin.o > > diff --git a/drivers/media/platform/rcar-vin/rcar-csi2.c > > b/drivers/media/platform/rcar-vin/rcar-csi2.c > > new file mode 100644 > > index 0000000000000000..b19374f1516464dc > > --- /dev/null > > +++ b/drivers/media/platform/rcar-vin/rcar-csi2.c > > @@ -0,0 +1,1101 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Driver for Renesas R-Car MIPI CSI-2 Receiver > > + * > > + * Copyright (C) 2018 Renesas Electronics Corp. > > + */ > > + > > +#include <linux/delay.h> > > +#include <linux/interrupt.h> > > +#include <linux/io.h> > > +#include <linux/module.h> > > +#include <linux/of.h> > > +#include <linux/of_device.h> > > +#include <linux/of_graph.h> > > +#include <linux/platform_device.h> > > +#include <linux/pm_runtime.h> > > +#include <linux/sys_soc.h> > > + > > +#include <media/v4l2-ctrls.h> > > +#include <media/v4l2-device.h> > > +#include <media/v4l2-fwnode.h> > > +#include <media/v4l2-mc.h> > > +#include <media/v4l2-subdev.h> > > + > > +struct rcar_csi2; > > + > > +/* Register offsets and bits */ > > + > > +/* Control Timing Select */ > > +#define TREF_REG 0x00 > > +#define TREF_TREF BIT(0) > > + > > +/* Software Reset */ > > +#define SRST_REG 0x04 > > +#define SRST_SRST BIT(0) > > + > > +/* PHY Operation Control */ > > +#define PHYCNT_REG 0x08 > > +#define PHYCNT_SHUTDOWNZ BIT(17) > > +#define PHYCNT_RSTZ BIT(16) > > +#define PHYCNT_ENABLECLK BIT(4) > > +#define PHYCNT_ENABLE_3 BIT(3) > > +#define PHYCNT_ENABLE_2 BIT(2) > > +#define PHYCNT_ENABLE_1 BIT(1) > > +#define PHYCNT_ENABLE_0 BIT(0) > > + > > +/* Checksum Control */ > > +#define CHKSUM_REG 0x0c > > +#define CHKSUM_ECC_EN BIT(1) > > +#define CHKSUM_CRC_EN BIT(0) > > + > > +/* > > + * Channel Data Type Select > > + * VCDT[0-15]: Channel 1 VCDT[16-31]: Channel 2 > > + * VCDT2[0-15]: Channel 3 VCDT2[16-31]: Channel 4 > > + */ > > +#define VCDT_REG 0x10 > > +#define VCDT2_REG 0x14 > > +#define VCDT_VCDTN_EN BIT(15) > > +#define VCDT_SEL_VC(n) (((n) & 0x3) << 8) > > +#define VCDT_SEL_DTN_ON BIT(6) > > +#define VCDT_SEL_DT(n) (((n) & 0x3f) << 0) > > + > > +/* Frame Data Type Select */ > > +#define FRDT_REG 0x18 > > + > > +/* Field Detection Control */ > > +#define FLD_REG 0x1c > > +#define FLD_FLD_NUM(n) (((n) & 0xff) << 16) > > +#define FLD_FLD_EN4 BIT(3) > > +#define FLD_FLD_EN3 BIT(2) > > +#define FLD_FLD_EN2 BIT(1) > > +#define FLD_FLD_EN BIT(0) > > + > > +/* Automatic Standby Control */ > > +#define ASTBY_REG 0x20 > > + > > +/* Long Data Type Setting 0 */ > > +#define LNGDT0_REG 0x28 > > + > > +/* Long Data Type Setting 1 */ > > +#define LNGDT1_REG 0x2c > > + > > +/* Interrupt Enable */ > > +#define INTEN_REG 0x30 > > + > > +/* Interrupt Source Mask */ > > +#define INTCLOSE_REG 0x34 > > + > > +/* Interrupt Status Monitor */ > > +#define INTSTATE_REG 0x38 > > +#define INTSTATE_INT_ULPS_START BIT(7) > > +#define INTSTATE_INT_ULPS_END BIT(6) > > + > > +/* Interrupt Error Status Monitor */ > > +#define INTERRSTATE_REG 0x3c > > + > > +/* Short Packet Data */ > > +#define SHPDAT_REG 0x40 > > + > > +/* Short Packet Count */ > > +#define SHPCNT_REG 0x44 > > + > > +/* LINK Operation Control */ > > +#define LINKCNT_REG 0x48 > > +#define LINKCNT_MONITOR_EN BIT(31) > > +#define LINKCNT_REG_MONI_PACT_EN BIT(25) > > +#define LINKCNT_ICLK_NONSTOP BIT(24) > > + > > +/* Lane Swap */ > > +#define LSWAP_REG 0x4c > > +#define LSWAP_L3SEL(n) (((n) & 0x3) << 6) > > +#define LSWAP_L2SEL(n) (((n) & 0x3) << 4) > > +#define LSWAP_L1SEL(n) (((n) & 0x3) << 2) > > +#define LSWAP_L0SEL(n) (((n) & 0x3) << 0) > > + > > +/* PHY Test Interface Write Register */ > > +#define PHTW_REG 0x50 > > +#define PHTW_DWEN BIT(24) > > +#define PHTW_TESTDIN_DATA(n) (((n & 0xff)) << 16) > > +#define PHTW_CWEN BIT(8) > > +#define PHTW_TESTDIN_CODE(n) ((n & 0xff)) > > [snip] > > > +/* PHY Test Interface Clear */ > > +#define PHTC_REG 0x58 > > +#define PHTC_TESTCLR BIT(0) > > + > > +/* PHY Frequency Control */ > > +#define PHYPLL_REG 0x68 > > +#define PHYPLL_HSFREQRANGE(n) ((n) << 16) > > + > > +struct phypll_hsfreqrange { > > + u16 mbps; > > + u16 reg; > > +}; > > + > > You'll be happy to know I see changes in these tables from datasheet > v.80 to datasheet v1.00 :( > > > +static const struct phypll_hsfreqrange hsfreqrange_h3_v3h_m3n[] = { > > + { .mbps = 80, .reg = 0x00 }, > > + { .mbps = 90, .reg = 0x10 }, > > + { .mbps = 100, .reg = 0x20 }, > > + { .mbps = 110, .reg = 0x30 }, > > + { .mbps = 120, .reg = 0x01 }, > > + { .mbps = 130, .reg = 0x11 }, > > + { .mbps = 140, .reg = 0x21 }, > > + { .mbps = 150, .reg = 0x31 }, > > + { .mbps = 160, .reg = 0x02 }, > > + { .mbps = 170, .reg = 0x12 }, > > + { .mbps = 180, .reg = 0x22 }, > > + { .mbps = 190, .reg = 0x32 }, > > + { .mbps = 205, .reg = 0x03 }, > > + { .mbps = 220, .reg = 0x13 }, > > + { .mbps = 235, .reg = 0x23 }, > > + { .mbps = 250, .reg = 0x33 }, > > + { .mbps = 275, .reg = 0x04 }, > > + { .mbps = 300, .reg = 0x14 }, > > + { .mbps = 325, .reg = 0x25 }, > > + { .mbps = 350, .reg = 0x35 }, > > + { .mbps = 400, .reg = 0x05 }, > > + { .mbps = 450, .reg = 0x26 }, > > Like here (reg = 0x16) > > > + { .mbps = 500, .reg = 0x36 }, > and here (reg = 0x26) > > I'm sure there will be more, but I'm happy to leave the funny part of > finding that out to you. I'm impressed by your review dedication :-) Indeed these two values have changed. I have checked all tables against the v1.0 datasheet and these two values are the only ones that have changed :-) Thanks for finding this! > > > + { .mbps = 550, .reg = 0x37 }, > > + { .mbps = 600, .reg = 0x07 }, > > + { .mbps = 650, .reg = 0x18 }, > > + { .mbps = 700, .reg = 0x28 }, > > + { .mbps = 750, .reg = 0x39 }, > > + { .mbps = 800, .reg = 0x09 }, > > + { .mbps = 850, .reg = 0x19 }, > > + { .mbps = 900, .reg = 0x29 }, > > + { .mbps = 950, .reg = 0x3a }, > > + { .mbps = 1000, .reg = 0x0a }, > > + { .mbps = 1050, .reg = 0x1a }, > > + { .mbps = 1100, .reg = 0x2a }, > > + { .mbps = 1150, .reg = 0x3b }, > > + { .mbps = 1200, .reg = 0x0b }, > > + { .mbps = 1250, .reg = 0x1b }, > > + { .mbps = 1300, .reg = 0x2b }, > > + { .mbps = 1350, .reg = 0x3c }, > > + { .mbps = 1400, .reg = 0x0c }, > > + { .mbps = 1450, .reg = 0x1c }, > > + { .mbps = 1500, .reg = 0x2c }, > > + { /* sentinel */ }, > > +}; > > It's very nice the reg values are nicely sorted and easily comparable. > Thanks hw manual -.- > > So far they seems good, I'll let you compare them for m3w > > > + > > +static const struct phypll_hsfreqrange hsfreqrange_m3w_h3es1[] = { > > + { .mbps = 80, .reg = 0x00 }, > > + { .mbps = 90, .reg = 0x10 }, > > + { .mbps = 100, .reg = 0x20 }, > > + { .mbps = 110, .reg = 0x30 }, > > + { .mbps = 120, .reg = 0x01 }, > > + { .mbps = 130, .reg = 0x11 }, > > + { .mbps = 140, .reg = 0x21 }, > > + { .mbps = 150, .reg = 0x31 }, > > + { .mbps = 160, .reg = 0x02 }, > > + { .mbps = 170, .reg = 0x12 }, > > + { .mbps = 180, .reg = 0x22 }, > > + { .mbps = 190, .reg = 0x32 }, > > + { .mbps = 205, .reg = 0x03 }, > > + { .mbps = 220, .reg = 0x13 }, > > + { .mbps = 235, .reg = 0x23 }, > > + { .mbps = 250, .reg = 0x33 }, > > + { .mbps = 275, .reg = 0x04 }, > > + { .mbps = 300, .reg = 0x14 }, > > + { .mbps = 325, .reg = 0x05 }, > > + { .mbps = 350, .reg = 0x15 }, > > + { .mbps = 400, .reg = 0x25 }, > > + { .mbps = 450, .reg = 0x06 }, > > + { .mbps = 500, .reg = 0x16 }, > > + { .mbps = 550, .reg = 0x07 }, > > + { .mbps = 600, .reg = 0x17 }, > > + { .mbps = 650, .reg = 0x08 }, > > + { .mbps = 700, .reg = 0x18 }, > > + { .mbps = 750, .reg = 0x09 }, > > + { .mbps = 800, .reg = 0x19 }, > > + { .mbps = 850, .reg = 0x29 }, > > + { .mbps = 900, .reg = 0x39 }, > > + { .mbps = 950, .reg = 0x0a }, > > + { .mbps = 1000, .reg = 0x1a }, > > + { .mbps = 1050, .reg = 0x2a }, > > + { .mbps = 1100, .reg = 0x3a }, > > + { .mbps = 1150, .reg = 0x0b }, > > + { .mbps = 1200, .reg = 0x1b }, > > + { .mbps = 1250, .reg = 0x2b }, > > + { .mbps = 1300, .reg = 0x3b }, > > + { .mbps = 1350, .reg = 0x0c }, > > + { .mbps = 1400, .reg = 0x1c }, > > + { .mbps = 1450, .reg = 0x2c }, > > + { .mbps = 1500, .reg = 0x3c }, > > + { /* sentinel */ }, > > +}; > > + > > +/* PHY ESC Error Monitor */ > > +#define PHEERM_REG 0x74 > > + > > +/* PHY Clock Lane Monitor */ > > +#define PHCLM_REG 0x78 > > +#define PHCLM_STOPSTATECKL BIT(0) > > + > > +/* PHY Data Lane Monitor */ > > +#define PHDLM_REG 0x7c > > + > > +/* CSI0CLK Frequency Configuration Preset Register */ > > +#define CSI0CLKFCPR_REG 0x260 > > +#define CSI0CLKFREQRANGE(n) ((n & 0x3f) << 16) > > + > > +struct rcar_csi2_format { > > + u32 code; > > + unsigned int datatype; > > + unsigned int bpp; > > +}; > > + > > +static const struct rcar_csi2_format rcar_csi2_formats[] = { > > + { .code = MEDIA_BUS_FMT_RGB888_1X24, .datatype = 0x24, .bpp = 24 }, > > + { .code = MEDIA_BUS_FMT_UYVY8_1X16, .datatype = 0x1e, .bpp = 16 }, > > + { .code = MEDIA_BUS_FMT_YUYV8_1X16, .datatype = 0x1e, .bpp = 16 }, > > + { .code = MEDIA_BUS_FMT_UYVY8_2X8, .datatype = 0x1e, .bpp = 16 }, > > + { .code = MEDIA_BUS_FMT_YUYV10_2X10, .datatype = 0x1e, .bpp = 20 }, > > +}; > > + > > +static const struct rcar_csi2_format *rcsi2_code_to_fmt(unsigned int code) > > +{ > > + unsigned int i; > > + > > + for (i = 0; i < ARRAY_SIZE(rcar_csi2_formats); i++) > > + if (rcar_csi2_formats[i].code == code) > > + return &rcar_csi2_formats[i]; > > + > > + return NULL; > > +} > > + > > +enum rcar_csi2_pads { > > + RCAR_CSI2_SINK, > > + RCAR_CSI2_SOURCE_VC0, > > + RCAR_CSI2_SOURCE_VC1, > > + RCAR_CSI2_SOURCE_VC2, > > + RCAR_CSI2_SOURCE_VC3, > > + NR_OF_RCAR_CSI2_PAD, > > +}; > > + > > +struct rcar_csi2_info { > > + int (*init_phtw)(struct rcar_csi2 *priv, unsigned int mbps); > > + const struct phypll_hsfreqrange *hsfreqrange; > > + unsigned int csi0clkfreqrange; > > + bool clear_ulps; > > +}; > > + > > +struct rcar_csi2 { > > + struct device *dev; > > + void __iomem *base; > > + const struct rcar_csi2_info *info; > > + > > + struct v4l2_subdev subdev; > > + struct media_pad pads[NR_OF_RCAR_CSI2_PAD]; > > + > > + struct v4l2_async_notifier notifier; > > + struct v4l2_async_subdev asd; > > + struct v4l2_subdev *remote; > > + > > + struct v4l2_mbus_framefmt mf; > > + > > + struct mutex lock; > > + int stream_count; > > + > > + unsigned short lanes; > > + unsigned char lane_swap[4]; > > +}; > > + > > +static inline struct rcar_csi2 *sd_to_csi2(struct v4l2_subdev *sd) > > +{ > > + return container_of(sd, struct rcar_csi2, subdev); > > +} > > + > > +static inline struct rcar_csi2 *notifier_to_csi2(struct > > v4l2_async_notifier *n) > > +{ > > + return container_of(n, struct rcar_csi2, notifier); > > +} > > + > > +static u32 rcsi2_read(struct rcar_csi2 *priv, unsigned int reg) > > +{ > > + return ioread32(priv->base + reg); > > +} > > + > > +static void rcsi2_write(struct rcar_csi2 *priv, unsigned int reg, u32 data) > > +{ > > + iowrite32(data, priv->base + reg); > > +} > > + > > +static void rcsi2_reset(struct rcar_csi2 *priv) > > +{ > > + rcsi2_write(priv, SRST_REG, SRST_SRST); > > + usleep_range(100, 150); > > + rcsi2_write(priv, SRST_REG, 0); > > +} > > + > > +static int rcsi2_wait_phy_start(struct rcar_csi2 *priv) > > +{ > > + int timeout; > > + > > + /* Wait for the clock and data lanes to enter LP-11 state. */ > > + for (timeout = 100; timeout > 0; timeout--) { > > + const u32 lane_mask = (1 << priv->lanes) - 1; > > + > > + if ((rcsi2_read(priv, PHCLM_REG) & PHCLM_STOPSTATECKL) && > > + (rcsi2_read(priv, PHDLM_REG) & lane_mask) == lane_mask) > > + return 0; > > + > > + msleep(20); > > + } > > + > > + dev_err(priv->dev, "Timeout waiting for LP-11 state\n"); > > + > > + return -ETIMEDOUT; > > +} > > + > > +static int rcsi2_set_phypll(struct rcar_csi2 *priv, unsigned int mbps) > > +{ > > + const struct phypll_hsfreqrange *hsfreq; > > + > > + for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++) > > + if (hsfreq->mbps >= mbps) > > + break; > > + > > + if (!hsfreq->mbps) { > > + dev_err(priv->dev, "Unsupported PHY speed (%u Mbps)", mbps); > > + return -ERANGE; > > + } > > + > > + dev_dbg(priv->dev, "PHY HSFREQRANGE requested %u got %u Mbps\n", mbps, > > + hsfreq->mbps); > > + > > + rcsi2_write(priv, PHYPLL_REG, PHYPLL_HSFREQRANGE(hsfreq->reg)); > > + > > + return 0; > > +} > > + > > +static int rcsi2_calc_mbps(struct rcar_csi2 *priv, unsigned int bpp) > > +{ > > + struct v4l2_subdev *source; > > + struct v4l2_ctrl *ctrl; > > + u64 mbps; > > + > > + if (!priv->remote) > > + return -ENODEV; > > + > > + source = priv->remote; > > + > > + /* Read the pixel rate control from remote. */ > > + ctrl = v4l2_ctrl_find(source->ctrl_handler, V4L2_CID_PIXEL_RATE); > > + if (!ctrl) { > > + dev_err(priv->dev, "no pixel rate control in subdev %s\n", > > + source->name); > > + return -EINVAL; > > + } > > + > > + /* > > + * Calculate the phypll in mbps (from v4l2 documentation). > > + * link_freq = (pixel_rate * bits_per_sample) / (2 * nr_of_lanes) > > + * bps = link_freq * 2 > > + */ > > + mbps = v4l2_ctrl_g_ctrl_int64(ctrl) * bpp; > > + do_div(mbps, priv->lanes * 1000000); > > + > > + return mbps; > > +} > > + > > +static int rcsi2_start(struct rcar_csi2 *priv) > > +{ > > + const struct rcar_csi2_format *format; > > + u32 phycnt, vcdt = 0, vcdt2 = 0; > > + unsigned int i; > > + int mbps, ret; > > + > > + dev_dbg(priv->dev, "Input size (%ux%u%c)\n", > > + priv->mf.width, priv->mf.height, > > + priv->mf.field == V4L2_FIELD_NONE ? 'p' : 'i'); > > + > > + /* Code is validated in set_fmt. */ > > + format = rcsi2_code_to_fmt(priv->mf.code); > > + > > + /* > > + * Enable all Virtual Channels. > > + * > > + * NOTE: It's not possible to get individual datatype for each > > + * source virtual channel. Once this is possible in V4L2 > > + * it should be used here. > > + */ > > + for (i = 0; i < 4; i++) { > > + u32 vcdt_part; > > + > > + vcdt_part = VCDT_SEL_VC(i) | VCDT_VCDTN_EN | VCDT_SEL_DTN_ON | > > + VCDT_SEL_DT(format->datatype); > > + > > + /* Store in correct reg and offset. */ > > + if (i < 2) > > + vcdt |= vcdt_part << ((i % 2) * 16); > > + else > > + vcdt2 |= vcdt_part << ((i % 2) * 16); > > + } > > + > > + phycnt = PHYCNT_ENABLECLK; > > + phycnt |= (1 << priv->lanes) - 1; > > + > > + mbps = rcsi2_calc_mbps(priv, format->bpp); > > + if (mbps < 0) > > + return mbps; > > + > > + /* Init */ > > + rcsi2_write(priv, TREF_REG, TREF_TREF); > > + rcsi2_reset(priv); > > + rcsi2_write(priv, PHTC_REG, 0); > > + > > + /* Configure */ > > + rcsi2_write(priv, FLD_REG, FLD_FLD_NUM(2) | FLD_FLD_EN4 | > > + FLD_FLD_EN3 | FLD_FLD_EN2 | FLD_FLD_EN); > > I see this has changed from datasheet v.80 to v1.00 and the FLD_ENn > bits have to be kept to 0 if capturing a pogressive image. This was > not clearly stated in previous datasheet version, and you are setting > those bits unconditionally here. As we spoke on IRC about this. Fixing this up will be part of a later patch-set. Disregarding if the datasheet update capture of both interlaced and progressive video works just fine when always setting this register. What will be real fun here is when we get multiple streams up and running as the FLD_FLD_NUM() controls which of the fields are odd/even. And we only got one FLD_FLD_NUM() register but we have one enable bit for each channel. What if we have two channels one with PAL and one with NTSC video running :-) But this is a problem for the future as currently we can't even set the video standard for the rcar-csi2 subdevice. > > Thanks > j > > > + rcsi2_write(priv, VCDT_REG, vcdt); > > + rcsi2_write(priv, VCDT2_REG, vcdt2); > > + /* Lanes are zero indexed. */ > > + rcsi2_write(priv, LSWAP_REG, > > + LSWAP_L0SEL(priv->lane_swap[0] - 1) | > > + LSWAP_L1SEL(priv->lane_swap[1] - 1) | > > + LSWAP_L2SEL(priv->lane_swap[2] - 1) | > > + LSWAP_L3SEL(priv->lane_swap[3] - 1)); > > + > > + /* Start */ > > + if (priv->info->init_phtw) { > > + ret = priv->info->init_phtw(priv, mbps); > > + if (ret) > > + return ret; > > + } > > + > > + if (priv->info->hsfreqrange) { > > + ret = rcsi2_set_phypll(priv, mbps); > > + if (ret) > > + return ret; > > + } > > + > > + if (priv->info->csi0clkfreqrange) > > + rcsi2_write(priv, CSI0CLKFCPR_REG, > > + CSI0CLKFREQRANGE(priv->info->csi0clkfreqrange)); > > + > > + rcsi2_write(priv, PHYCNT_REG, phycnt); > > + rcsi2_write(priv, LINKCNT_REG, LINKCNT_MONITOR_EN | > > + LINKCNT_REG_MONI_PACT_EN | LINKCNT_ICLK_NONSTOP); > > + rcsi2_write(priv, PHYCNT_REG, phycnt | PHYCNT_SHUTDOWNZ); > > + rcsi2_write(priv, PHYCNT_REG, phycnt | PHYCNT_SHUTDOWNZ | PHYCNT_RSTZ); > > + > > + ret = rcsi2_wait_phy_start(priv); > > + if (ret) > > + return ret; > > + > > + /* Clear Ultra Low Power interrupt. */ > > + if (priv->info->clear_ulps) > > + rcsi2_write(priv, INTSTATE_REG, > > + INTSTATE_INT_ULPS_START | > > + INTSTATE_INT_ULPS_END); > > + return 0; > > +} > > + > > +static void rcsi2_stop(struct rcar_csi2 *priv) > > +{ > > + rcsi2_write(priv, PHYCNT_REG, 0); > > + > > + rcsi2_reset(priv); > > + > > + rcsi2_write(priv, PHTC_REG, PHTC_TESTCLR); > > +} > > + > > +static int rcsi2_s_stream(struct v4l2_subdev *sd, int enable) > > +{ > > + struct rcar_csi2 *priv = sd_to_csi2(sd); > > + struct v4l2_subdev *nextsd; > > + int ret = 0; > > + > > + mutex_lock(&priv->lock); > > + > > + if (!priv->remote) { > > + ret = -ENODEV; > > + goto out; > > + } > > + > > + nextsd = priv->remote; > > + > > + if (enable && priv->stream_count == 0) { > > + pm_runtime_get_sync(priv->dev); > > + > > + ret = rcsi2_start(priv); > > + if (ret) { > > + pm_runtime_put(priv->dev); > > + goto out; > > + } > > + > > + ret = v4l2_subdev_call(nextsd, video, s_stream, 1); > > + if (ret) { > > + rcsi2_stop(priv); > > + pm_runtime_put(priv->dev); > > + goto out; > > + } > > + } else if (!enable && priv->stream_count == 1) { > > + rcsi2_stop(priv); > > + v4l2_subdev_call(nextsd, video, s_stream, 0); > > + pm_runtime_put(priv->dev); > > + } > > + > > + priv->stream_count += enable ? 1 : -1; > > +out: > > + mutex_unlock(&priv->lock); > > + > > + return ret; > > +} > > + > > +static int rcsi2_set_pad_format(struct v4l2_subdev *sd, > > + struct v4l2_subdev_pad_config *cfg, > > + struct v4l2_subdev_format *format) > > +{ > > + struct rcar_csi2 *priv = sd_to_csi2(sd); > > + struct v4l2_mbus_framefmt *framefmt; > > + > > + if (!rcsi2_code_to_fmt(format->format.code)) > > + return -EINVAL; > > + > > + if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) { > > + priv->mf = format->format; > > + } else { > > + framefmt = v4l2_subdev_get_try_format(sd, cfg, 0); > > + *framefmt = format->format; > > + } > > + > > + return 0; > > +} > > + > > +static int rcsi2_get_pad_format(struct v4l2_subdev *sd, > > + struct v4l2_subdev_pad_config *cfg, > > + struct v4l2_subdev_format *format) > > +{ > > + struct rcar_csi2 *priv = sd_to_csi2(sd); > > + > > + if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) > > + format->format = priv->mf; > > + else > > + format->format = *v4l2_subdev_get_try_format(sd, cfg, 0); > > + > > + return 0; > > +} > > + > > +static const struct v4l2_subdev_video_ops rcar_csi2_video_ops = { > > + .s_stream = rcsi2_s_stream, > > +}; > > + > > +static const struct v4l2_subdev_pad_ops rcar_csi2_pad_ops = { > > + .set_fmt = rcsi2_set_pad_format, > > + .get_fmt = rcsi2_get_pad_format, > > +}; > > + > > +static const struct v4l2_subdev_ops rcar_csi2_subdev_ops = { > > + .video = &rcar_csi2_video_ops, > > + .pad = &rcar_csi2_pad_ops, > > +}; > > + > > +/* > > ----------------------------------------------------------------------------- > > + * Async handling and registration of subdevices and links. > > + */ > > + > > +static int rcsi2_notify_bound(struct v4l2_async_notifier *notifier, > > + struct v4l2_subdev *subdev, > > + struct v4l2_async_subdev *asd) > > +{ > > + struct rcar_csi2 *priv = notifier_to_csi2(notifier); > > + int pad; > > + > > + pad = media_entity_get_fwnode_pad(&subdev->entity, asd->match.fwnode, > > + MEDIA_PAD_FL_SOURCE); > > + if (pad < 0) { > > + dev_err(priv->dev, "Failed to find pad for %s\n", subdev->name); > > + return pad; > > + } > > + > > + priv->remote = subdev; > > + > > + dev_dbg(priv->dev, "Bound %s pad: %d\n", subdev->name, pad); > > + > > + return media_create_pad_link(&subdev->entity, pad, > > + &priv->subdev.entity, 0, > > + MEDIA_LNK_FL_ENABLED | > > + MEDIA_LNK_FL_IMMUTABLE); > > +} > > + > > +static void rcsi2_notify_unbind(struct v4l2_async_notifier *notifier, > > + struct v4l2_subdev *subdev, > > + struct v4l2_async_subdev *asd) > > +{ > > + struct rcar_csi2 *priv = notifier_to_csi2(notifier); > > + > > + priv->remote = NULL; > > + > > + dev_dbg(priv->dev, "Unbind %s\n", subdev->name); > > +} > > + > > +static const struct v4l2_async_notifier_operations rcar_csi2_notify_ops = { > > + .bound = rcsi2_notify_bound, > > + .unbind = rcsi2_notify_unbind, > > +}; > > + > > +static int rcsi2_parse_v4l2(struct rcar_csi2 *priv, > > + struct v4l2_fwnode_endpoint *vep) > > +{ > > + unsigned int i; > > + > > + /* Only port 0 endpoint 0 is valid. */ > > + if (vep->base.port || vep->base.id) > > + return -ENOTCONN; > > + > > + if (vep->bus_type != V4L2_MBUS_CSI2) { > > + dev_err(priv->dev, "Unsupported bus: %u\n", vep->bus_type); > > + return -EINVAL; > > + } > > + > > + priv->lanes = vep->bus.mipi_csi2.num_data_lanes; > > + if (priv->lanes != 1 && priv->lanes != 2 && priv->lanes != 4) { > > + dev_err(priv->dev, "Unsupported number of data-lanes: %u\n", > > + priv->lanes); > > + return -EINVAL; > > + } > > + > > + for (i = 0; i < ARRAY_SIZE(priv->lane_swap); i++) { > > + priv->lane_swap[i] = i < priv->lanes ? > > + vep->bus.mipi_csi2.data_lanes[i] : i; > > + > > + /* Check for valid lane number. */ > > + if (priv->lane_swap[i] < 1 || priv->lane_swap[i] > 4) { > > + dev_err(priv->dev, "data-lanes must be in 1-4 range\n"); > > + return -EINVAL; > > + } > > + } > > + > > + return 0; > > +} > > + > > +static int rcsi2_parse_dt(struct rcar_csi2 *priv) > > +{ > > + struct device_node *ep; > > + struct v4l2_fwnode_endpoint v4l2_ep; > > + int ret; > > + > > + ep = of_graph_get_endpoint_by_regs(priv->dev->of_node, 0, 0); > > > + if (!ep) { > > + dev_err(priv->dev, "Not connected to subdevice\n"); > > + return -EINVAL; > > + } > > + > > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &v4l2_ep); > > + if (ret) { > > + dev_err(priv->dev, "Could not parse v4l2 endpoint\n"); > > + of_node_put(ep); > > + return -EINVAL; > > + } > > + > > + ret = rcsi2_parse_v4l2(priv, &v4l2_ep); > > + if (ret) { > > + of_node_put(ep); > > + return ret; > > + } > > + > > + priv->asd.match.fwnode = > > + fwnode_graph_get_remote_endpoint(of_fwnode_handle(ep)); > > + priv->asd.match_type = V4L2_ASYNC_MATCH_FWNODE; > > + > > + of_node_put(ep); > > + > > + priv->notifier.subdevs = devm_kzalloc(priv->dev, > > + sizeof(*priv->notifier.subdevs), > > + GFP_KERNEL); > > + if (!priv->notifier.subdevs) > > + return -ENOMEM; > > + > > + priv->notifier.num_subdevs = 1; > > + priv->notifier.subdevs[0] = &priv->asd; > > + priv->notifier.ops = &rcar_csi2_notify_ops; > > + > > + dev_dbg(priv->dev, "Found '%pOF'\n", > > + to_of_node(priv->asd.match.fwnode)); > > + > > + return v4l2_async_subdev_notifier_register(&priv->subdev, > > + &priv->notifier); > > +} > > + > > +/* > > ----------------------------------------------------------------------------- > > + * PHTW unitizing sequences. > > + * > > + * NOTE: Magic values are from the datasheet and lack documentation. > > + */ > > + > > +static int rcsi2_phtw_write(struct rcar_csi2 *priv, u16 data, u16 code) > > +{ > > + unsigned int timeout; > > + > > + rcsi2_write(priv, PHTW_REG, > > + PHTW_DWEN | PHTW_TESTDIN_DATA(data) | > > + PHTW_CWEN | PHTW_TESTDIN_CODE(code)); > > + > > + /* Wait for DWEN and CWEN to be cleared by hardware. */ > > + for (timeout = 100; timeout > 0; timeout--) { > > + if (!(rcsi2_read(priv, PHTW_REG) & (PHTW_DWEN | PHTW_CWEN))) > > + return 0; > > + msleep(20); > > + } > > + > > + dev_err(priv->dev, "Timeout waiting for PHTW_DWEN and/or PHTW_CWEN\n"); > > + > > + return -ETIMEDOUT; > > +} > > + > > +static int rcsi2_phtw_write_array(struct rcar_csi2 *priv, > > + const struct phtw_value *values) > > +{ > > + const struct phtw_value *value; > > + int ret; > > + > > + for (value = values; (value->data || value->code); value++) { > > + ret = rcsi2_phtw_write(priv, value->data, value->code); > > + if (ret) > > + return ret; > > + } > > + > > + return 0; > > +} > > + > > +static int rcsi2_phtw_write_mbps(struct rcar_csi2 *priv, unsigned int mbps, > > + const struct phtw_mbps *values, u16 code) > > +{ > > + const struct phtw_mbps *value; > > + > > + for (value = values; value->mbps; value++) > > + if (value->mbps >= mbps) > > + break; > > + > > + if (!value->mbps) { > > + dev_err(priv->dev, "Unsupported PHY speed (%u Mbps)", mbps); > > + return -ERANGE; > > + } > > + > > + dev_dbg(priv->dev, "PHTW requested %u got %u Mbps\n", mbps, > > + value->mbps); > > + > > + return rcsi2_phtw_write(priv, value->data, code); > > +} > > + > > +static int rcsi2_init_phtw_h3_v3h_m3n(struct rcar_csi2 *priv, unsigned int > > mbps) > > +{ > > + static const struct phtw_value step1[] = { > > + { .data = 0xcc, .code = 0xe2 }, > > + { .data = 0x01, .code = 0xe3 }, > > + { .data = 0x11, .code = 0xe4 }, > > + { .data = 0x01, .code = 0xe5 }, > > + { .data = 0x10, .code = 0x04 }, > > + { /* sentinel */ }, > > + }; > > + > > + static const struct phtw_value step2[] = { > > + { .data = 0x38, .code = 0x08 }, > > + { .data = 0x01, .code = 0x00 }, > > + { .data = 0x4b, .code = 0xac }, > > + { .data = 0x03, .code = 0x00 }, > > + { .data = 0x80, .code = 0x07 }, > > + { /* sentinel */ }, > > + }; > > + > > + int ret; > > + > > + ret = rcsi2_phtw_write_array(priv, step1); > > + if (ret) > > + return ret; > > + > > + if (mbps <= 250) { > > + ret = rcsi2_phtw_write(priv, 0x39, 0x05); > > + if (ret) > > + return ret; > > + > > + ret = rcsi2_phtw_write_mbps(priv, mbps, phtw_mbps_h3_v3h_m3n, > > + 0xf1); > > + if (ret) > > + return ret; > > + } > > + > > + return rcsi2_phtw_write_array(priv, step2); > > +} > > + > > +static int rcsi2_init_phtw_v3m_e3(struct rcar_csi2 *priv, unsigned int > > mbps) > > +{ > > + static const struct phtw_value step1[] = { > > + { .data = 0xed, .code = 0x34 }, > > + { .data = 0xed, .code = 0x44 }, > > + { .data = 0xed, .code = 0x54 }, > > + { .data = 0xed, .code = 0x84 }, > > + { .data = 0xed, .code = 0x94 }, > > + { /* sentinel */ }, > > + }; > > + > > + int ret; > > + > > + ret = rcsi2_phtw_write_mbps(priv, mbps, phtw_mbps_v3m_e3, 0x44); > > + if (ret) > > + return ret; > > + > > + return rcsi2_phtw_write_array(priv, step1); > > +} > > + > > +/* > > ----------------------------------------------------------------------------- > > + * Platform Device Driver. > > + */ > > + > > +static const struct media_entity_operations rcar_csi2_entity_ops = { > > + .link_validate = v4l2_subdev_link_validate, > > +}; > > + > > +static int rcsi2_probe_resources(struct rcar_csi2 *priv, > > + struct platform_device *pdev) > > +{ > > + struct resource *res; > > + int irq; > > + > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > + priv->base = devm_ioremap_resource(&pdev->dev, res); > > + if (IS_ERR(priv->base)) > > + return PTR_ERR(priv->base); > > + > > + irq = platform_get_irq(pdev, 0); > > + if (irq < 0) > > + return irq; > > + > > + return 0; > > +} > > + > > +static const struct rcar_csi2_info rcar_csi2_info_r8a7795 = { > > + .init_phtw = rcsi2_init_phtw_h3_v3h_m3n, > > + .hsfreqrange = hsfreqrange_h3_v3h_m3n, > > + .csi0clkfreqrange = 0x20, > > + .clear_ulps = true, > > +}; > > + > > +static const struct rcar_csi2_info rcar_csi2_info_r8a7795es1 = { > > + .hsfreqrange = hsfreqrange_m3w_h3es1, > > +}; > > + > > +static const struct rcar_csi2_info rcar_csi2_info_r8a7796 = { > > + .hsfreqrange = hsfreqrange_m3w_h3es1, > > +}; > > + > > +static const struct rcar_csi2_info rcar_csi2_info_r8a77965 = { > > + .init_phtw = rcsi2_init_phtw_h3_v3h_m3n, > > + .hsfreqrange = hsfreqrange_h3_v3h_m3n, > > + .csi0clkfreqrange = 0x20, > > + .clear_ulps = true, > > +}; > > + > > +static const struct rcar_csi2_info rcar_csi2_info_r8a77970 = { > > + .init_phtw = rcsi2_init_phtw_v3m_e3, > > +}; > > + > > +static const struct of_device_id rcar_csi2_of_table[] = { > > + { > > + .compatible = "renesas,r8a7795-csi2", > > + .data = &rcar_csi2_info_r8a7795, > > + }, > > + { > > + .compatible = "renesas,r8a7796-csi2", > > + .data = &rcar_csi2_info_r8a7796, > > + }, > > + { > > + .compatible = "renesas,r8a77965-csi2", > > + .data = &rcar_csi2_info_r8a77965, > > + }, > > + { > > + .compatible = "renesas,r8a77970-csi2", > > + .data = &rcar_csi2_info_r8a77970, > > + }, > > + { /* sentinel */ }, > > +}; > > +MODULE_DEVICE_TABLE(of, rcar_csi2_of_table); > > + > > +static const struct soc_device_attribute r8a7795es1[] = { > > + { > > + .soc_id = "r8a7795", .revision = "ES1.*", > > + .data = &rcar_csi2_info_r8a7795es1, > > + }, > > + { /* sentinel */ }, > > +}; > > + > > +static int rcsi2_probe(struct platform_device *pdev) > > +{ > > + const struct soc_device_attribute *attr; > > + struct rcar_csi2 *priv; > > + unsigned int i; > > + int ret; > > + > > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > > + if (!priv) > > + return -ENOMEM; > > + > > + priv->info = of_device_get_match_data(&pdev->dev); > > + > > + /* > > + * r8a7795 ES1.x behaves differently than the ES2.0+ but doesn't > > + * have it's own compatible string. > > + */ > > + attr = soc_device_match(r8a7795es1); > > + if (attr) > > + priv->info = attr->data; > > + > > + priv->dev = &pdev->dev; > > + > > + mutex_init(&priv->lock); > > + priv->stream_count = 0; > > + > > + ret = rcsi2_probe_resources(priv, pdev); > > + if (ret) { > > + dev_err(priv->dev, "Failed to get resources\n"); > > + return ret; > > + } > > + > > + platform_set_drvdata(pdev, priv); > > + > > + ret = rcsi2_parse_dt(priv); > > + if (ret) > > + return ret; > > + > > + priv->subdev.owner = THIS_MODULE; > > + priv->subdev.dev = &pdev->dev; > > + v4l2_subdev_init(&priv->subdev, &rcar_csi2_subdev_ops); > > + v4l2_set_subdevdata(&priv->subdev, &pdev->dev); > > + snprintf(priv->subdev.name, V4L2_SUBDEV_NAME_SIZE, "%s %s", > > + KBUILD_MODNAME, dev_name(&pdev->dev)); > > + priv->subdev.flags = V4L2_SUBDEV_FL_HAS_DEVNODE; > > + > > + priv->subdev.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER; > > + priv->subdev.entity.ops = &rcar_csi2_entity_ops; > > + > > + priv->pads[RCAR_CSI2_SINK].flags = MEDIA_PAD_FL_SINK; > > + for (i = RCAR_CSI2_SOURCE_VC0; i < NR_OF_RCAR_CSI2_PAD; i++) > > + priv->pads[i].flags = MEDIA_PAD_FL_SOURCE; > > + > > + ret = media_entity_pads_init(&priv->subdev.entity, NR_OF_RCAR_CSI2_PAD, > > + priv->pads); > > + if (ret) > > + goto error; > > + > > + pm_runtime_enable(&pdev->dev); > > + > > + ret = v4l2_async_register_subdev(&priv->subdev); > > + if (ret < 0) > > + goto error; > > + > > + dev_info(priv->dev, "%d lanes found\n", priv->lanes); > > + > > + return 0; > > + > > +error: > > + v4l2_async_notifier_unregister(&priv->notifier); > > + v4l2_async_notifier_cleanup(&priv->notifier); > > + > > + return ret; > > +} > > + > > +static int rcsi2_remove(struct platform_device *pdev) > > +{ > > + struct rcar_csi2 *priv = platform_get_drvdata(pdev); > > + > > + v4l2_async_notifier_unregister(&priv->notifier); > > + v4l2_async_notifier_cleanup(&priv->notifier); > > + v4l2_async_unregister_subdev(&priv->subdev); > > + > > + pm_runtime_disable(&pdev->dev); > > + > > + return 0; > > +} > > + > > +static struct platform_driver __refdata rcar_csi2_pdrv = { > > + .remove = rcsi2_remove, > > + .probe = rcsi2_probe, > > + .driver = { > > + .name = "rcar-csi2", > > + .of_match_table = rcar_csi2_of_table, > > + }, > > +}; > > + > > +module_platform_driver(rcar_csi2_pdrv); > > + > > +MODULE_AUTHOR("Niklas Söderlund <niklas.soderl...@ragnatech.se>"); > > +MODULE_DESCRIPTION("Renesas R-Car MIPI CSI-2 receiver"); > > +MODULE_LICENSE("GPL"); > > -- > > 2.17.0 > > -- Regards, Niklas Söderlund