Heiko Stübner wrote: > > Hi Vinod, > > with the removed double-retrival of the cookie state, is the driver ok now? > Because I think kgene needs an ack on it. > Yes! Vinod, do you OK on this? If you have any concerns, please kindly let us know.
Thanks, Kukjin > > Thanks > Heiko > > > Am Mittwoch, 18. September 2013, 21:19:54 schrieb Heiko Stübner: > > This adds a new driver to support the s3c24xx dma using the dmaengine > > and makes the old one in mach-s3c24xx obsolete in the long run. > > > > Conceptually the s3c24xx-dma feels like a distant relative of the pl08x > > with numerous virtual channels being mapped to a lot less physical ones. > > The driver therefore borrows a lot from the amba-pl08x driver in this > > regard. Functionality-wise the driver gains a memcpy ability in addition > > to the slave_sg one. > > > > The driver supports both the method for requesting the peripheral used > > by SoCs before the S3C2443 and the different method for S3C2443 and > later. > > > > On earlier SoCs the hardware channels usable for specific peripherals is > > constrainted while on later SoCs all channels can be used for any > > peripheral. > > > > Tested on a s3c2416-based board, memcpy using the dmatest module and > > slave_sg partially using the spi-s3c64xx driver. > > > > Signed-off-by: Heiko Stuebner <he...@sntech.de> > > Acked-by: Linus Walleij <linus.wall...@linaro.org> > > --- > > changes since v4: > > - fix the unnecessary double retrieval of the cookie status > > pointed out by Vinod Koul > > changes since v3: > > - address comments from Tomasz Figa: > > - fixed a lot of nitpics > > - and added a rudimentary mechanism to select higher bus-widths for > > memcpy - address more comments from Vinod Koul - reorder dma_control > > contents > > > > changes since v2: > > - add missing channel validation in s3c24xx_dma_phy_free when > repurposing > > a physical channel for another virtual channel > > - address comments from Vinod Koul: > > - fix naming of constants to prevent conflicts > > - better handle the unlikely case of an interrupt happening on an > > unused channel > > > > changes since v1: > > - address comments from Linus Walleij > > - support sg-lists with more than 1 element > > - add support for earlier s3c24xx SoCs > > - redo the channeldata definitions: > > - no need for static ids for the virtual channels > > - provide a way to encode constraints for earlier variants > > - better base for later dt bindings > > > > drivers/dma/Kconfig | 12 + > > drivers/dma/Makefile | 1 + > > drivers/dma/s3c24xx-dma.c | 1340 > > +++++++++++++++++++++++++++++ include/linux/platform_data/dma-s3c24xx.h > | > > 43 + > > 4 files changed, 1396 insertions(+) > > create mode 100644 drivers/dma/s3c24xx-dma.c > > create mode 100644 include/linux/platform_data/dma-s3c24xx.h > > > > diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig > > index 526ec77..d639115 100644 > > --- a/drivers/dma/Kconfig > > +++ b/drivers/dma/Kconfig > > @@ -154,6 +154,18 @@ config TEGRA20_APB_DMA > > This DMA controller transfers data from memory to peripheral fifo > > or vice versa. It does not support memory to memory data transfer. > > > > +config S3C24XX_DMAC > > + tristate "Samsung S3C24XX DMA support" > > + depends on ARCH_S3C24XX && !S3C24XX_DMA > > + select DMA_ENGINE > > + select DMA_VIRTUAL_CHANNELS > > + help > > + Support for the Samsung S3C24XX DMA controller driver. The > > + DMA controller is having multiple DMA channels which can be > > + configured for different peripherals like audio, UART, SPI. > > + The DMA controller can transfer data from memory to peripheral, > > + periphal to memory, periphal to periphal and memory to memory. > > + > > source "drivers/dma/sh/Kconfig" > > > > config COH901318 > > diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile > > index db89035..0ce2da9 100644 > > --- a/drivers/dma/Makefile > > +++ b/drivers/dma/Makefile > > @@ -30,6 +30,7 @@ obj-$(CONFIG_SIRF_DMA) += sirf-dma.o > > obj-$(CONFIG_TI_EDMA) += edma.o > > obj-$(CONFIG_STE_DMA40) += ste_dma40.o ste_dma40_ll.o > > obj-$(CONFIG_TEGRA20_APB_DMA) += tegra20-apb-dma.o > > +obj-$(CONFIG_S3C24XX_DMAC) += s3c24xx-dma.o > > obj-$(CONFIG_PL330_DMA) += pl330.o > > obj-$(CONFIG_PCH_DMA) += pch_dma.o > > obj-$(CONFIG_AMBA_PL08X) += amba-pl08x.o > > diff --git a/drivers/dma/s3c24xx-dma.c b/drivers/dma/s3c24xx-dma.c > > new file mode 100644 > > index 0000000..56c9253 > > --- /dev/null > > +++ b/drivers/dma/s3c24xx-dma.c > > @@ -0,0 +1,1340 @@ > > +/* > > + * S3C24XX DMA handling > > + * > > + * Copyright (c) 2013 Heiko Stuebner <he...@sntech.de> > > + * > > + * based on amba-pl08x.c > > + * > > + * Copyright (c) 2006 ARM Ltd. > > + * Copyright (c) 2010 ST-Ericsson SA > > + * > > + * Author: Peter Pearse <peter.pea...@arm.com> > > + * Author: Linus Walleij <linus.wall...@stericsson.com> > > + * > > + * This program is free software; you can redistribute it and/or modify > it > > + * under the terms of the GNU General Public License as published by > the > > Free + * Software Foundation; either version 2 of the License, or (at > your > > option) + * any later version. > > + * > > + * The DMA controllers in S3C24XX SoCs have a varying number of DMA > > signals + * that can be routed to any of the 4 to 8 hardware-channels. > > + * > > + * Therefore on these DMA controllers the number of channels > > + * and the number of incoming DMA signals are two totally different > > things. + * It is usually not possible to theoretically handle all > > physical signals, + * so a multiplexing scheme with possible denial of > use > > is necessary. + * > > + * Open items: > > + * - bursts > > + */ > > + > > +#include <linux/platform_device.h> > > +#include <linux/types.h> > > +#include <linux/dmaengine.h> > > +#include <linux/dma-mapping.h> > > +#include <linux/interrupt.h> > > +#include <linux/clk.h> > > +#include <linux/module.h> > > +#include <linux/slab.h> > > +#include <linux/platform_data/dma-s3c24xx.h> > > + > > +#include "dmaengine.h" > > +#include "virt-dma.h" > > + > > +#define MAX_DMA_CHANNELS 8 > > + > > +#define S3C24XX_DISRC 0x00 > > +#define S3C24XX_DISRCC 0x04 > > +#define S3C24XX_DISRCC_INC_INCREMENT 0 > > +#define S3C24XX_DISRCC_INC_FIXED BIT(0) > > +#define S3C24XX_DISRCC_LOC_AHB 0 > > +#define S3C24XX_DISRCC_LOC_APB BIT(1) > > + > > +#define S3C24XX_DIDST 0x08 > > +#define S3C24XX_DIDSTC 0x0c > > +#define S3C24XX_DIDSTC_INC_INCREMENT 0 > > +#define S3C24XX_DIDSTC_INC_FIXED BIT(0) > > +#define S3C24XX_DIDSTC_LOC_AHB 0 > > +#define S3C24XX_DIDSTC_LOC_APB BIT(1) > > +#define S3C24XX_DIDSTC_INT_TC0 0 > > +#define S3C24XX_DIDSTC_INT_RELOAD BIT(2) > > + > > +#define S3C24XX_DCON 0x10 > > + > > +#define S3C24XX_DCON_TC_MASK 0xfffff > > +#define S3C24XX_DCON_DSZ_BYTE (0 << 20) > > +#define S3C24XX_DCON_DSZ_HALFWORD (1 << 20) > > +#define S3C24XX_DCON_DSZ_WORD (2 << 20) > > +#define S3C24XX_DCON_DSZ_MASK (3 << 20) > > +#define S3C24XX_DCON_DSZ_SHIFT 20 > > +#define S3C24XX_DCON_AUTORELOAD 0 > > +#define S3C24XX_DCON_NORELOAD BIT(22) > > +#define S3C24XX_DCON_HWTRIG BIT(23) > > +#define S3C24XX_DCON_HWSRC_SHIFT 24 > > +#define S3C24XX_DCON_SERV_SINGLE 0 > > +#define S3C24XX_DCON_SERV_WHOLE BIT(27) > > +#define S3C24XX_DCON_TSZ_UNIT 0 > > +#define S3C24XX_DCON_TSZ_BURST4 BIT(28) > > +#define S3C24XX_DCON_INT BIT(29) > > +#define S3C24XX_DCON_SYNC_PCLK 0 > > +#define S3C24XX_DCON_SYNC_HCLK BIT(30) > > +#define S3C24XX_DCON_DEMAND 0 > > +#define S3C24XX_DCON_HANDSHAKE BIT(31) > > + > > +#define S3C24XX_DSTAT 0x14 > > +#define S3C24XX_DSTAT_STAT_BUSY BIT(20) > > +#define S3C24XX_DSTAT_CURRTC_MASK 0xfffff > > + > > +#define S3C24XX_DMASKTRIG 0x20 > > +#define S3C24XX_DMASKTRIG_SWTRIG BIT(0) > > +#define S3C24XX_DMASKTRIG_ON BIT(1) > > +#define S3C24XX_DMASKTRIG_STOP BIT(2) > > + > > +#define S3C24XX_DMAREQSEL 0x24 > > +#define S3C24XX_DMAREQSEL_HW BIT(0) > > + > > +/* > > + * S3C2410, S3C2440 and S3C2442 SoCs cannot select any physical channel > > + * for a DMA source. Instead only specific channels are valid. > > + * All of these SoCs have 4 physical channels and the number of request > > + * source bits is 3. Additionally we also need 1 bit to mark the > channel > > + * as valid. > > + * Therefore we separate the chansel element of the channel data into 4 > > + * parts of 4 bits each, to hold the information if the channel is > valid > > + * and the hw request source to use. > > + * > > + * Example: > > + * SDI is valid on channels 0, 2 and 3 - with varying hw request > sources. > > + * For it the chansel field would look like > > + * > > + * ((BIT(3) | 1) << 3 * 4) | // channel 3, with request source 1 > > + * ((BIT(3) | 2) << 2 * 4) | // channel 2, with request source 2 > > + * ((BIT(3) | 2) << 0 * 4) // channel 0, with request source 2 > > + */ > > +#define S3C24XX_CHANSEL_WIDTH 4 > > +#define S3C24XX_CHANSEL_VALID BIT(3) > > +#define S3C24XX_CHANSEL_REQ_MASK 7 > > + > > +/* > > + * struct soc_data - vendor-specific config parameters for individual > SoCs > > + * @stride: spacing between the registers of each channel > > + * @has_reqsel: does the controller use the newer requestselection > > mechanism + * @has_clocks: are controllable dma-clocks present > > + */ > > +struct soc_data { > > + int stride; > > + bool has_reqsel; > > + bool has_clocks; > > +}; > > + > > +/* > > + * enum s3c24xx_dma_chan_state - holds the virtual channel states > > + * @S3C24XX_DMA_CHAN_IDLE: the channel is idle > > + * @S3C24XX_DMA_CHAN_RUNNING: the channel has allocated a physical > > transport + * channel and is running a transfer on it > > + * @S3C24XX_DMA_CHAN_WAITING: the channel is waiting for a physical > > transport + * channel to become available (only pertains to memcpy > > channels) + */ > > +enum s3c24xx_dma_chan_state { > > + S3C24XX_DMA_CHAN_IDLE, > > + S3C24XX_DMA_CHAN_RUNNING, > > + S3C24XX_DMA_CHAN_WAITING, > > +}; > > + > > +/* > > + * struct s3c24xx_sg - structure containing data per sg > > + * @src_addr: src address of sg > > + * @dst_addr: dst address of sg > > + * @len: transfer len in bytes > > + * @node: node for txd's dsg_list > > + */ > > +struct s3c24xx_sg { > > + dma_addr_t src_addr; > > + dma_addr_t dst_addr; > > + size_t len; > > + struct list_head node; > > +}; > > + > > +/* > > + * struct s3c24xx_txd - wrapper for struct dma_async_tx_descriptor > > + * @vd: virtual DMA descriptor > > + * @dsg_list: list of children sg's > > + * @at: sg currently being transfered > > + * @width: transfer width > > + * @disrcc: value for source control register > > + * @didstc: value for destination control register > > + * @dcon: base value for dcon register > > + */ > > +struct s3c24xx_txd { > > + struct virt_dma_desc vd; > > + struct list_head dsg_list; > > + struct list_head *at; > > + u8 width; > > + u32 disrcc; > > + u32 didstc; > > + u32 dcon; > > +}; > > + > > +struct s3c24xx_dma_chan; > > + > > +/* > > + * struct s3c24xx_dma_phy - holder for the physical channels > > + * @id: physical index to this channel > > + * @valid: does the channel have all required elements > > + * @base: virtual memory base (remapped) for the this channel > > + * @irq: interrupt for this channel > > + * @clk: clock for this channel > > + * @lock: a lock to use when altering an instance of this struct > > + * @serving: virtual channel currently being served by this > > physicalchannel + * @host: a pointer to the host (internal use) > > + */ > > +struct s3c24xx_dma_phy { > > + unsigned int id; > > + bool valid; > > + void __iomem *base; > > + unsigned int irq; > > + struct clk *clk; > > + spinlock_t lock; > > + struct s3c24xx_dma_chan *serving; > > + struct s3c24xx_dma_engine *host; > > +}; > > + > > +/* > > + * struct s3c24xx_dma_chan - this structure wraps a DMA ENGINE channel > > + * @id: the id of the channel > > + * @name: name of the channel > > + * @vc: wrappped virtual channel > > + * @phy: the physical channel utilized by this channel, if there is one > > + * @runtime_addr: address for RX/TX according to the runtime config > > + * @at: active transaction on this channel > > + * @lock: a lock for this channel data > > + * @host: a pointer to the host (internal use) > > + * @state: whether the channel is idle, running etc > > + * @slave: whether this channel is a device (slave) or for memcpy > > + */ > > +struct s3c24xx_dma_chan { > > + int id; > > + const char *name; > > + struct virt_dma_chan vc; > > + struct s3c24xx_dma_phy *phy; > > + struct dma_slave_config cfg; > > + struct s3c24xx_txd *at; > > + struct s3c24xx_dma_engine *host; > > + enum s3c24xx_dma_chan_state state; > > + bool slave; > > +}; > > + > > +/* > > + * struct s3c24xx_dma_engine - the local state holder for the S3C24XX > > + * @pdev: the corresponding platform device > > + * @pdata: platform data passed in from the platform/machine > > + * @base: virtual memory base (remapped) > > + * @slave: slave engine for this instance > > + * @memcpy: memcpy engine for this instance > > + * @phy_chans: array of data for the physical channels > > + */ > > +struct s3c24xx_dma_engine { > > + struct platform_device *pdev; > > + const struct s3c24xx_dma_platdata *pdata; > > + struct soc_data *sdata; > > + void __iomem *base; > > + struct dma_device slave; > > + struct dma_device memcpy; > > + struct s3c24xx_dma_phy *phy_chans; > > +}; > > + > > +/* > > + * Physical channel handling > > + */ > > + > > +/* > > + * Check whether a certain channel is busy or not. > > + */ > > +static int s3c24xx_dma_phy_busy(struct s3c24xx_dma_phy *phy) > > +{ > > + unsigned int val = readl(phy->base + S3C24XX_DSTAT); > > + return val & S3C24XX_DSTAT_STAT_BUSY; > > +} > > + > > +static bool s3c24xx_dma_phy_valid(struct s3c24xx_dma_chan *s3cchan, > > + struct s3c24xx_dma_phy *phy) > > +{ > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + const struct s3c24xx_dma_platdata *pdata = s3cdma->pdata; > > + struct s3c24xx_dma_channel *cdata = &pdata->channels[s3cchan->id]; > > + int phyvalid; > > + > > + /* every phy is valid for memcopy channels */ > > + if (!s3cchan->slave) > > + return true; > > + > > + /* On newer variants all phys can be used for all virtual channels > */ > > + if (s3cdma->sdata->has_reqsel) > > + return true; > > + > > + phyvalid = (cdata->chansel >> (phy->id * S3C24XX_CHANSEL_WIDTH)); > > + return (phyvalid & S3C24XX_CHANSEL_VALID) ? true : false; > > +} > > + > > +/* > > + * Allocate a physical channel for a virtual channel > > + * > > + * Try to locate a physical channel to be used for this transfer. If > all > > + * are taken return NULL and the requester will have to cope by using > > + * some fallback PIO mode or retrying later. > > + */ > > +static > > +struct s3c24xx_dma_phy *s3c24xx_dma_get_phy(struct s3c24xx_dma_chan > > *s3cchan) +{ > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + const struct s3c24xx_dma_platdata *pdata = s3cdma->pdata; > > + struct s3c24xx_dma_channel *cdata; > > + struct s3c24xx_dma_phy *phy = NULL; > > + unsigned long flags; > > + int i; > > + int ret; > > + > > + if (s3cchan->slave) > > + cdata = &pdata->channels[s3cchan->id]; > > + > > + for (i = 0; i < s3cdma->pdata->num_phy_channels; i++) { > > + phy = &s3cdma->phy_chans[i]; > > + > > + if (!phy->valid) > > + continue; > > + > > + if (!s3c24xx_dma_phy_valid(s3cchan, phy)) > > + continue; > > + > > + spin_lock_irqsave(&phy->lock, flags); > > + > > + if (!phy->serving) { > > + phy->serving = s3cchan; > > + spin_unlock_irqrestore(&phy->lock, flags); > > + break; > > + } > > + > > + spin_unlock_irqrestore(&phy->lock, flags); > > + } > > + > > + /* No physical channel available, cope with it */ > > + if (i == s3cdma->pdata->num_phy_channels) { > > + dev_warn(&s3cdma->pdev->dev, "no phy channel available\n"); > > + return NULL; > > + } > > + > > + /* start the phy clock */ > > + if (s3cdma->sdata->has_clocks) { > > + ret = clk_enable(phy->clk); > > + if (ret) { > > + dev_err(&s3cdma->pdev->dev, "could not enable clock > for channel > %d, err > > %d\n", + phy->id, ret); > > + phy->serving = NULL; > > + return NULL; > > + } > > + } > > + > > + return phy; > > +} > > + > > +/* > > + * Mark the physical channel as free. > > + * > > + * This drops the link between the physical and virtual channel. > > + */ > > +static inline void s3c24xx_dma_put_phy(struct s3c24xx_dma_phy *phy) > > +{ > > + struct s3c24xx_dma_engine *s3cdma = phy->host; > > + > > + if (s3cdma->sdata->has_clocks) > > + clk_disable(phy->clk); > > + > > + phy->serving = NULL; > > +} > > + > > +/* > > + * Stops the channel by writing the stop bit. > > + * This should not be used for an on-going transfer, but as a method of > > + * shutting down a channel (eg, when it's no longer used) or > terminating a > > + * transfer. > > + */ > > +static void s3c24xx_dma_terminate_phy(struct s3c24xx_dma_phy *phy) > > +{ > > + writel(S3C24XX_DMASKTRIG_STOP, phy->base + S3C24XX_DMASKTRIG); > > +} > > + > > +/* > > + * Virtual channel handling > > + */ > > + > > +static inline > > +struct s3c24xx_dma_chan *to_s3c24xx_dma_chan(struct dma_chan *chan) > > +{ > > + return container_of(chan, struct s3c24xx_dma_chan, vc.chan); > > +} > > + > > +static u32 s3c24xx_dma_getbytes_chan(struct s3c24xx_dma_chan *s3cchan) > > +{ > > + struct s3c24xx_dma_phy *phy = s3cchan->phy; > > + struct s3c24xx_txd *txd = s3cchan->at; > > + u32 tc = readl(phy->base + S3C24XX_DSTAT) & > S3C24XX_DSTAT_CURRTC_MASK; > > + > > + return tc * txd->width; > > +} > > + > > +static int s3c24xx_dma_set_runtime_config(struct s3c24xx_dma_chan > > *s3cchan, + struct dma_slave_config *config) > > +{ > > + if (!s3cchan->slave) > > + return -EINVAL; > > + > > + /* Reject definitely invalid configurations */ > > + if (config->src_addr_width == DMA_SLAVE_BUSWIDTH_8_BYTES || > > + config->dst_addr_width == DMA_SLAVE_BUSWIDTH_8_BYTES) > > + return -EINVAL; > > + > > + s3cchan->cfg = *config; > > + > > + return 0; > > +} > > + > > +/* > > + * Transfer handling > > + */ > > + > > +static inline > > +struct s3c24xx_txd *to_s3c24xx_txd(struct dma_async_tx_descriptor *tx) > > +{ > > + return container_of(tx, struct s3c24xx_txd, vd.tx); > > +} > > + > > +static struct s3c24xx_txd *s3c24xx_dma_get_txd(void) > > +{ > > + struct s3c24xx_txd *txd = kzalloc(sizeof(*txd), GFP_NOWAIT); > > + > > + if (txd) { > > + INIT_LIST_HEAD(&txd->dsg_list); > > + txd->dcon = S3C24XX_DCON_INT | S3C24XX_DCON_NORELOAD; > > + } > > + > > + return txd; > > +} > > + > > +static void s3c24xx_dma_free_txd(struct s3c24xx_txd *txd) > > +{ > > + struct s3c24xx_sg *dsg, *_dsg; > > + > > + list_for_each_entry_safe(dsg, _dsg, &txd->dsg_list, node) { > > + list_del(&dsg->node); > > + kfree(dsg); > > + } > > + > > + kfree(txd); > > +} > > + > > +static void s3c24xx_dma_start_next_sg(struct s3c24xx_dma_chan *s3cchan, > > + struct s3c24xx_txd *txd) > > +{ > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + struct s3c24xx_dma_phy *phy = s3cchan->phy; > > + const struct s3c24xx_dma_platdata *pdata = s3cdma->pdata; > > + struct s3c24xx_sg *dsg = list_entry(txd->at, struct s3c24xx_sg, > node); > > + u32 dcon = txd->dcon; > > + u32 val; > > + > > + /* transfer-size and -count from len and width */ > > + switch (txd->width) { > > + case 1: > > + dcon |= S3C24XX_DCON_DSZ_BYTE | dsg->len; > > + break; > > + case 2: > > + dcon |= S3C24XX_DCON_DSZ_HALFWORD | (dsg->len / 2); > > + break; > > + case 4: > > + dcon |= S3C24XX_DCON_DSZ_WORD | (dsg->len / 4); > > + break; > > + } > > + > > + if (s3cchan->slave) { > > + struct s3c24xx_dma_channel *cdata = > > + &pdata->channels[s3cchan->id]; > > + > > + if (s3cdma->sdata->has_reqsel) { > > + writel_relaxed((cdata->chansel << 1) | > > + S3C24XX_DMAREQSEL_HW, > > + phy->base + S3C24XX_DMAREQSEL); > > + } else { > > + int csel = cdata->chansel >> (phy->id * > > + S3C24XX_CHANSEL_WIDTH); > > + > > + csel &= S3C24XX_CHANSEL_REQ_MASK; > > + dcon |= csel << S3C24XX_DCON_HWSRC_SHIFT; > > + dcon |= S3C24XX_DCON_HWTRIG; > > + } > > + } else { > > + if (s3cdma->sdata->has_reqsel) > > + writel_relaxed(0, phy->base + S3C24XX_DMAREQSEL); > > + } > > + > > + writel_relaxed(dsg->src_addr, phy->base + S3C24XX_DISRC); > > + writel_relaxed(txd->disrcc, phy->base + S3C24XX_DISRCC); > > + writel_relaxed(dsg->dst_addr, phy->base + S3C24XX_DIDST); > > + writel_relaxed(txd->didstc, phy->base + S3C24XX_DIDSTC); > > + writel_relaxed(dcon, phy->base + S3C24XX_DCON); > > + > > + val = readl_relaxed(phy->base + S3C24XX_DMASKTRIG); > > + val &= ~S3C24XX_DMASKTRIG_STOP; > > + val |= S3C24XX_DMASKTRIG_ON; > > + > > + /* trigger the dma operation for memcpy transfers */ > > + if (!s3cchan->slave) > > + val |= S3C24XX_DMASKTRIG_SWTRIG; > > + > > + writel(val, phy->base + S3C24XX_DMASKTRIG); > > +} > > + > > +/* > > + * Set the initial DMA register values and start first sg. > > + */ > > +static void s3c24xx_dma_start_next_txd(struct s3c24xx_dma_chan *s3cchan) > > +{ > > + struct s3c24xx_dma_phy *phy = s3cchan->phy; > > + struct virt_dma_desc *vd = vchan_next_desc(&s3cchan->vc); > > + struct s3c24xx_txd *txd = to_s3c24xx_txd(&vd->tx); > > + > > + list_del(&txd->vd.node); > > + > > + s3cchan->at = txd; > > + > > + /* Wait for channel inactive */ > > + while (s3c24xx_dma_phy_busy(phy)) > > + cpu_relax(); > > + > > + /* point to the first element of the sg list */ > > + txd->at = txd->dsg_list.next; > > + s3c24xx_dma_start_next_sg(s3cchan, txd); > > +} > > + > > +static void s3c24xx_dma_free_txd_list(struct s3c24xx_dma_engine *s3cdma, > > + struct s3c24xx_dma_chan *s3cchan) > > +{ > > + LIST_HEAD(head); > > + > > + vchan_get_all_descriptors(&s3cchan->vc, &head); > > + vchan_dma_desc_free_list(&s3cchan->vc, &head); > > +} > > + > > +/* > > + * Try to allocate a physical channel. When successful, assign it to > > + * this virtual channel, and initiate the next descriptor. The > > + * virtual channel lock must be held at this point. > > + */ > > +static void s3c24xx_dma_phy_alloc_and_start(struct s3c24xx_dma_chan > > *s3cchan) +{ > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + struct s3c24xx_dma_phy *phy; > > + > > + phy = s3c24xx_dma_get_phy(s3cchan); > > + if (!phy) { > > + dev_dbg(&s3cdma->pdev->dev, "no physical channel available > for xfer > on > > %s\n", + s3cchan->name); > > + s3cchan->state = S3C24XX_DMA_CHAN_WAITING; > > + return; > > + } > > + > > + dev_dbg(&s3cdma->pdev->dev, "allocated physical channel %d for xfer > on > > %s\n", + phy->id, s3cchan->name); > > + > > + s3cchan->phy = phy; > > + s3cchan->state = S3C24XX_DMA_CHAN_RUNNING; > > + > > + s3c24xx_dma_start_next_txd(s3cchan); > > +} > > + > > +static void s3c24xx_dma_phy_reassign_start(struct s3c24xx_dma_phy *phy, > > + struct s3c24xx_dma_chan *s3cchan) > > +{ > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + > > + dev_dbg(&s3cdma->pdev->dev, "reassigned physical channel %d for > xfer on > > %s\n", + phy->id, s3cchan->name); > > + > > + /* > > + * We do this without taking the lock; we're really only concerned > > + * about whether this pointer is NULL or not, and we're guaranteed > > + * that this will only be called when it _already_ is non-NULL. > > + */ > > + phy->serving = s3cchan; > > + s3cchan->phy = phy; > > + s3cchan->state = S3C24XX_DMA_CHAN_RUNNING; > > + s3c24xx_dma_start_next_txd(s3cchan); > > +} > > + > > +/* > > + * Free a physical DMA channel, potentially reallocating it to another > > + * virtual channel if we have any pending. > > + */ > > +static void s3c24xx_dma_phy_free(struct s3c24xx_dma_chan *s3cchan) > > +{ > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + struct s3c24xx_dma_chan *p, *next; > > + > > +retry: > > + next = NULL; > > + > > + /* Find a waiting virtual channel for the next transfer. */ > > + list_for_each_entry(p, &s3cdma->memcpy.channels, > vc.chan.device_node) > > + if (p->state == S3C24XX_DMA_CHAN_WAITING) { > > + next = p; > > + break; > > + } > > + > > + if (!next) { > > + list_for_each_entry(p, &s3cdma->slave.channels, > > + vc.chan.device_node) > > + if (p->state == S3C24XX_DMA_CHAN_WAITING && > > + s3c24xx_dma_phy_valid(p, s3cchan->phy)) { > > + next = p; > > + break; > > + } > > + } > > + > > + /* Ensure that the physical channel is stopped */ > > + s3c24xx_dma_terminate_phy(s3cchan->phy); > > + > > + if (next) { > > + bool success; > > + > > + /* > > + * Eww. We know this isn't going to deadlock > > + * but lockdep probably doesn't. > > + */ > > + spin_lock(&next->vc.lock); > > + /* Re-check the state now that we have the lock */ > > + success = next->state == S3C24XX_DMA_CHAN_WAITING; > > + if (success) > > + s3c24xx_dma_phy_reassign_start(s3cchan->phy, next); > > + spin_unlock(&next->vc.lock); > > + > > + /* If the state changed, try to find another channel */ > > + if (!success) > > + goto retry; > > + } else { > > + /* No more jobs, so free up the physical channel */ > > + s3c24xx_dma_put_phy(s3cchan->phy); > > + } > > + > > + s3cchan->phy = NULL; > > + s3cchan->state = S3C24XX_DMA_CHAN_IDLE; > > +} > > + > > +static void s3c24xx_dma_unmap_buffers(struct s3c24xx_txd *txd) > > +{ > > + struct device *dev = txd->vd.tx.chan->device->dev; > > + struct s3c24xx_sg *dsg; > > + > > + if (!(txd->vd.tx.flags & DMA_COMPL_SKIP_SRC_UNMAP)) { > > + if (txd->vd.tx.flags & DMA_COMPL_SRC_UNMAP_SINGLE) > > + list_for_each_entry(dsg, &txd->dsg_list, node) > > + dma_unmap_single(dev, dsg->src_addr, dsg->len, > > + DMA_TO_DEVICE); > > + else { > > + list_for_each_entry(dsg, &txd->dsg_list, node) > > + dma_unmap_page(dev, dsg->src_addr, dsg->len, > > + DMA_TO_DEVICE); > > + } > > + } > > + > > + if (!(txd->vd.tx.flags & DMA_COMPL_SKIP_DEST_UNMAP)) { > > + if (txd->vd.tx.flags & DMA_COMPL_DEST_UNMAP_SINGLE) > > + list_for_each_entry(dsg, &txd->dsg_list, node) > > + dma_unmap_single(dev, dsg->dst_addr, dsg->len, > > + DMA_FROM_DEVICE); > > + else > > + list_for_each_entry(dsg, &txd->dsg_list, node) > > + dma_unmap_page(dev, dsg->dst_addr, dsg->len, > > + DMA_FROM_DEVICE); > > + } > > +} > > + > > +static void s3c24xx_dma_desc_free(struct virt_dma_desc *vd) > > +{ > > + struct s3c24xx_txd *txd = to_s3c24xx_txd(&vd->tx); > > + struct s3c24xx_dma_chan *s3cchan = to_s3c24xx_dma_chan(vd->tx.chan); > > + > > + if (!s3cchan->slave) > > + s3c24xx_dma_unmap_buffers(txd); > > + > > + s3c24xx_dma_free_txd(txd); > > +} > > + > > +static irqreturn_t s3c24xx_dma_irq(int irq, void *data) > > +{ > > + struct s3c24xx_dma_phy *phy = data; > > + struct s3c24xx_dma_chan *s3cchan = phy->serving; > > + struct s3c24xx_txd *txd; > > + > > + dev_dbg(&phy->host->pdev->dev, "interrupt on channel %d\n", phy- > >id); > > + > > + /* > > + * Interrupts happen to notify the completion of a transfer and the > > + * channel should have moved into its stop state already on its own. > > + * Therefore interrupts on channels not bound to a virtual channel > > + * should never happen. Nevertheless send a terminate command to > the > > + * channel if the unlikely case happens. > > + */ > > + if (unlikely(!s3cchan)) { > > + dev_err(&phy->host->pdev->dev, "interrupt on unused > channel %d\n", > > + phy->id); > > + > > + s3c24xx_dma_terminate_phy(phy); > > + > > + return IRQ_HANDLED; > > + } > > + > > + spin_lock(&s3cchan->vc.lock); > > + txd = s3cchan->at; > > + if (txd) { > > + /* when more sg's are in this txd, start the next one */ > > + if (!list_is_last(txd->at, &txd->dsg_list)) { > > + txd->at = txd->at->next; > > + s3c24xx_dma_start_next_sg(s3cchan, txd); > > + } else { > > + s3cchan->at = NULL; > > + vchan_cookie_complete(&txd->vd); > > + > > + /* > > + * And start the next descriptor (if any), > > + * otherwise free this channel. > > + */ > > + if (vchan_next_desc(&s3cchan->vc)) > > + s3c24xx_dma_start_next_txd(s3cchan); > > + else > > + s3c24xx_dma_phy_free(s3cchan); > > + } > > + } > > + spin_unlock(&s3cchan->vc.lock); > > + > > + return IRQ_HANDLED; > > +} > > + > > +/* > > + * The DMA ENGINE API > > + */ > > + > > +static int s3c24xx_dma_control(struct dma_chan *chan, enum dma_ctrl_cmd > > cmd, + unsigned long arg) > > +{ > > + struct s3c24xx_dma_chan *s3cchan = to_s3c24xx_dma_chan(chan); > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + unsigned long flags; > > + int ret = 0; > > + > > + spin_lock_irqsave(&s3cchan->vc.lock, flags); > > + > > + switch (cmd) { > > + case DMA_SLAVE_CONFIG: > > + ret = s3c24xx_dma_set_runtime_config(s3cchan, > > + (struct dma_slave_config *)arg); > > + break; > > + case DMA_TERMINATE_ALL: > > + if (!s3cchan->phy && !s3cchan->at) { > > + dev_err(&s3cdma->pdev->dev, "trying to terminate > already stopped > > channel %d\n", + s3cchan->id); > > + ret = -EINVAL; > > + break; > > + } > > + > > + s3cchan->state = S3C24XX_DMA_CHAN_IDLE; > > + > > + /* Mark physical channel as free */ > > + if (s3cchan->phy) > > + s3c24xx_dma_phy_free(s3cchan); > > + > > + /* Dequeue current job */ > > + if (s3cchan->at) { > > + s3c24xx_dma_desc_free(&s3cchan->at->vd); > > + s3cchan->at = NULL; > > + } > > + > > + /* Dequeue jobs not yet fired as well */ > > + s3c24xx_dma_free_txd_list(s3cdma, s3cchan); > > + break; > > + default: > > + /* Unknown command */ > > + ret = -ENXIO; > > + break; > > + } > > + > > + spin_unlock_irqrestore(&s3cchan->vc.lock, flags); > > + > > + return ret; > > +} > > + > > +static int s3c24xx_dma_alloc_chan_resources(struct dma_chan *chan) > > +{ > > + return 0; > > +} > > + > > +static void s3c24xx_dma_free_chan_resources(struct dma_chan *chan) > > +{ > > + /* Ensure all queued descriptors are freed */ > > + vchan_free_chan_resources(to_virt_chan(chan)); > > +} > > + > > +static enum dma_status s3c24xx_dma_tx_status(struct dma_chan *chan, > > + dma_cookie_t cookie, struct dma_tx_state *txstate) > > +{ > > + struct s3c24xx_dma_chan *s3cchan = to_s3c24xx_dma_chan(chan); > > + struct s3c24xx_txd *txd; > > + struct s3c24xx_sg *dsg; > > + struct virt_dma_desc *vd; > > + unsigned long flags; > > + enum dma_status ret; > > + size_t bytes = 0; > > + > > + spin_lock_irqsave(&s3cchan->vc.lock, flags); > > + ret = dma_cookie_status(chan, cookie, txstate); > > + if (ret == DMA_SUCCESS) { > > + spin_unlock_irqrestore(&s3cchan->vc.lock, flags); > > + return ret; > > + } > > + > > + /* > > + * There's no point calculating the residue if there's > > + * no txstate to store the value. > > + */ > > + if (!txstate) { > > + spin_unlock_irqrestore(&s3cchan->vc.lock, flags); > > + return ret; > > + } > > + > > + vd = vchan_find_desc(&s3cchan->vc, cookie); > > + if (vd) { > > + /* On the issued list, so hasn't been processed yet */ > > + txd = to_s3c24xx_txd(&vd->tx); > > + > > + list_for_each_entry(dsg, &txd->dsg_list, node) > > + bytes += dsg->len; > > + } else { > > + /* > > + * Currently running, so sum over the pending sg's and > > + * the currently active one. > > + */ > > + txd = s3cchan->at; > > + > > + dsg = list_entry(txd->at, struct s3c24xx_sg, node); > > + list_for_each_entry_from(dsg, &txd->dsg_list, node) > > + bytes += dsg->len; > > + > > + bytes += s3c24xx_dma_getbytes_chan(s3cchan); > > + } > > + spin_unlock_irqrestore(&s3cchan->vc.lock, flags); > > + > > + /* > > + * This cookie not complete yet > > + * Get number of bytes left in the active transactions and queue > > + */ > > + dma_set_residue(txstate, bytes); > > + > > + /* Whether waiting or running, we're in progress */ > > + return ret; > > +} > > + > > +/* > > + * Initialize a descriptor to be used by memcpy submit > > + */ > > +static struct dma_async_tx_descriptor *s3c24xx_dma_prep_memcpy( > > + struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, > > + size_t len, unsigned long flags) > > +{ > > + struct s3c24xx_dma_chan *s3cchan = to_s3c24xx_dma_chan(chan); > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + struct s3c24xx_txd *txd; > > + struct s3c24xx_sg *dsg; > > + int src_mod, dest_mod; > > + > > + dev_dbg(&s3cdma->pdev->dev, "prepare memcpy of %d bytes from %s\n", > > + len, s3cchan->name); > > + > > + if ((len & S3C24XX_DCON_TC_MASK) != len) { > > + dev_err(&s3cdma->pdev->dev, "memcpy size %d to large\n", > len); > > + return NULL; > > + } > > + > > + txd = s3c24xx_dma_get_txd(); > > + if (!txd) > > + return NULL; > > + > > + dsg = kzalloc(sizeof(*dsg), GFP_NOWAIT); > > + if (!dsg) { > > + s3c24xx_dma_free_txd(txd); > > + return NULL; > > + } > > + list_add_tail(&dsg->node, &txd->dsg_list); > > + > > + dsg->src_addr = src; > > + dsg->dst_addr = dest; > > + dsg->len = len; > > + > > + /* > > + * Determine a suitable transfer width. > > + * The DMA controller cannot fetch/store information which is not > > + * naturally aligned on the bus, i.e., a 4 byte fetch must start at > > + * an address divisible by 4 - more generally addr % width must be > 0. > > + */ > > + src_mod = src % 4; > > + dest_mod = dest % 4; > > + switch (len % 4) { > > + case 0: > > + txd->width = (src_mod == 0 && dest_mod == 0) ? 4 : 1; > > + break; > > + case 2: > > + txd->width = ((src_mod == 2 || src_mod == 0) && > > + (dest_mod == 2 || dest_mod == 0)) ? 2 : 1; > > + break; > > + default: > > + txd->width = 1; > > + break; > > + } > > + > > + txd->disrcc = S3C24XX_DISRCC_LOC_AHB | S3C24XX_DISRCC_INC_INCREMENT; > > + txd->didstc = S3C24XX_DIDSTC_LOC_AHB | S3C24XX_DIDSTC_INC_INCREMENT; > > + txd->dcon |= S3C24XX_DCON_DEMAND | S3C24XX_DCON_SYNC_HCLK | > > + S3C24XX_DCON_SERV_WHOLE; > > + > > + return vchan_tx_prep(&s3cchan->vc, &txd->vd, flags); > > +} > > + > > +static struct dma_async_tx_descriptor *s3c24xx_dma_prep_slave_sg( > > + struct dma_chan *chan, struct scatterlist *sgl, > > + unsigned int sg_len, enum dma_transfer_direction direction, > > + unsigned long flags, void *context) > > +{ > > + struct s3c24xx_dma_chan *s3cchan = to_s3c24xx_dma_chan(chan); > > + struct s3c24xx_dma_engine *s3cdma = s3cchan->host; > > + const struct s3c24xx_dma_platdata *pdata = s3cdma->pdata; > > + struct s3c24xx_dma_channel *cdata = &pdata->channels[s3cchan->id]; > > + struct s3c24xx_txd *txd; > > + struct s3c24xx_sg *dsg; > > + struct scatterlist *sg; > > + dma_addr_t slave_addr; > > + u32 hwcfg = 0; > > + int tmp; > > + > > + dev_dbg(&s3cdma->pdev->dev, "prepare transaction of %d bytes > from %s\n", > > + sg_dma_len(sgl), s3cchan->name); > > + > > + txd = s3c24xx_dma_get_txd(); > > + if (!txd) > > + return NULL; > > + > > + if (cdata->handshake) > > + txd->dcon |= S3C24XX_DCON_HANDSHAKE; > > + > > + switch (cdata->bus) { > > + case S3C24XX_DMA_APB: > > + txd->dcon |= S3C24XX_DCON_SYNC_PCLK; > > + hwcfg |= S3C24XX_DISRCC_LOC_APB; > > + break; > > + case S3C24XX_DMA_AHB: > > + txd->dcon |= S3C24XX_DCON_SYNC_HCLK; > > + hwcfg |= S3C24XX_DISRCC_LOC_AHB; > > + break; > > + } > > + > > + /* > > + * Always assume our peripheral desintation is a fixed > > + * address in memory. > > + */ > > + hwcfg |= S3C24XX_DISRCC_INC_FIXED; > > + > > + /* > > + * Individual dma operations are requested by the slave, > > + * so serve only single atomic operations > (S3C24XX_DCON_SERV_SINGLE). > > + */ > > + txd->dcon |= S3C24XX_DCON_SERV_SINGLE; > > + > > + if (direction == DMA_MEM_TO_DEV) { > > + txd->disrcc = S3C24XX_DISRCC_LOC_AHB | > > + S3C24XX_DISRCC_INC_INCREMENT; > > + txd->didstc = hwcfg; > > + slave_addr = s3cchan->cfg.dst_addr; > > + txd->width = s3cchan->cfg.dst_addr_width; > > + } else if (direction == DMA_DEV_TO_MEM) { > > + txd->disrcc = hwcfg; > > + txd->didstc = S3C24XX_DIDSTC_LOC_AHB | > > + S3C24XX_DIDSTC_INC_INCREMENT; > > + slave_addr = s3cchan->cfg.src_addr; > > + txd->width = s3cchan->cfg.src_addr_width; > > + } else { > > + s3c24xx_dma_free_txd(txd); > > + dev_err(&s3cdma->pdev->dev, > > + "direction %d unsupported\n", direction); > > + return NULL; > > + } > > + > > + for_each_sg(sgl, sg, sg_len, tmp) { > > + dsg = kzalloc(sizeof(*dsg), GFP_NOWAIT); > > + if (!dsg) { > > + s3c24xx_dma_free_txd(txd); > > + return NULL; > > + } > > + list_add_tail(&dsg->node, &txd->dsg_list); > > + > > + dsg->len = sg_dma_len(sg); > > + if (direction == DMA_MEM_TO_DEV) { > > + dsg->src_addr = sg_dma_address(sg); > > + dsg->dst_addr = slave_addr; > > + } else { /* DMA_DEV_TO_MEM */ > > + dsg->src_addr = slave_addr; > > + dsg->dst_addr = sg_dma_address(sg); > > + } > > + break; > > + } > > + > > + return vchan_tx_prep(&s3cchan->vc, &txd->vd, flags); > > +} > > + > > +/* > > + * Slave transactions callback to the slave device to allow > > + * synchronization of slave DMA signals with the DMAC enable > > + */ > > +static void s3c24xx_dma_issue_pending(struct dma_chan *chan) > > +{ > > + struct s3c24xx_dma_chan *s3cchan = to_s3c24xx_dma_chan(chan); > > + unsigned long flags; > > + > > + spin_lock_irqsave(&s3cchan->vc.lock, flags); > > + if (vchan_issue_pending(&s3cchan->vc)) { > > + if (!s3cchan->phy && s3cchan->state != > S3C24XX_DMA_CHAN_WAITING) > > + s3c24xx_dma_phy_alloc_and_start(s3cchan); > > + } > > + spin_unlock_irqrestore(&s3cchan->vc.lock, flags); > > +} > > + > > +/* > > + * Bringup and teardown > > + */ > > + > > +/* > > + * Initialise the DMAC memcpy/slave channels. > > + * Make a local wrapper to hold required data > > + */ > > +static int s3c24xx_dma_init_virtual_channels(struct s3c24xx_dma_engine > > *s3cdma, + struct dma_device *dmadev, unsigned int channels, bool > slave) > > +{ > > + struct s3c24xx_dma_chan *chan; > > + int i; > > + > > + INIT_LIST_HEAD(&dmadev->channels); > > + > > + /* > > + * Register as many many memcpy as we have physical channels, > > + * we won't always be able to use all but the code will have > > + * to cope with that situation. > > + */ > > + for (i = 0; i < channels; i++) { > > + chan = devm_kzalloc(dmadev->dev, sizeof(*chan), GFP_KERNEL); > > + if (!chan) { > > + dev_err(dmadev->dev, > > + "%s no memory for channel\n", __func__); > > + return -ENOMEM; > > + } > > + > > + chan->id = i; > > + chan->host = s3cdma; > > + chan->state = S3C24XX_DMA_CHAN_IDLE; > > + > > + if (slave) { > > + chan->slave = true; > > + chan->name = kasprintf(GFP_KERNEL, "slave%d", i); > > + if (!chan->name) > > + return -ENOMEM; > > + } else { > > + chan->name = kasprintf(GFP_KERNEL, "memcpy%d", i); > > + if (!chan->name) > > + return -ENOMEM; > > + } > > + dev_dbg(dmadev->dev, > > + "initialize virtual channel \"%s\"\n", > > + chan->name); > > + > > + chan->vc.desc_free = s3c24xx_dma_desc_free; > > + vchan_init(&chan->vc, dmadev); > > + } > > + dev_info(dmadev->dev, "initialized %d virtual %s channels\n", > > + i, slave ? "slave" : "memcpy"); > > + return i; > > +} > > + > > +static void s3c24xx_dma_free_virtual_channels(struct dma_device *dmadev) > > +{ > > + struct s3c24xx_dma_chan *chan = NULL; > > + struct s3c24xx_dma_chan *next; > > + > > + list_for_each_entry_safe(chan, > > + next, &dmadev->channels, vc.chan.device_node) > > + list_del(&chan->vc.chan.device_node); > > +} > > + > > +/* s3c2412 and s3c2413 have a 0x40 stride and dmareqsel mechanism */ > > +static struct soc_data soc_s3c2412 = { > > + .stride = 0x40, > > + .has_reqsel = true, > > + .has_clocks = true, > > +}; > > + > > +/* s3c2443 and following have a 0x100 stride and dmareqsel mechanism */ > > +static struct soc_data soc_s3c2443 = { > > + .stride = 0x100, > > + .has_reqsel = true, > > + .has_clocks = true, > > +}; > > + > > +static struct platform_device_id s3c24xx_dma_driver_ids[] = { > > + { > > + .name = "s3c2412-dma", > > + .driver_data = (kernel_ulong_t)&soc_s3c2412, > > + }, { > > + .name = "s3c2443-dma", > > + .driver_data = (kernel_ulong_t)&soc_s3c2443, > > + }, > > + { }, > > +}; > > + > > +static struct soc_data *s3c24xx_dma_get_soc_data(struct platform_device > > *pdev) +{ > > + return (struct soc_data *) > > + platform_get_device_id(pdev)->driver_data; > > +} > > + > > +static int s3c24xx_dma_probe(struct platform_device *pdev) > > +{ > > + const struct s3c24xx_dma_platdata *pdata = dev_get_platdata(&pdev- > >dev); > > + struct s3c24xx_dma_engine *s3cdma; > > + struct soc_data *sdata; > > + struct resource *res; > > + int ret; > > + int i; > > + > > + if (!pdata) { > > + dev_err(&pdev->dev, "platform data missing\n"); > > + return -ENODEV; > > + } > > + > > + /* Basic sanity check */ > > + if (pdata->num_phy_channels > MAX_DMA_CHANNELS) { > > + dev_err(&pdev->dev, "to many dma channels %d, max %d\n", > > + pdata->num_phy_channels, MAX_DMA_CHANNELS); > > + return -EINVAL; > > + } > > + > > + sdata = s3c24xx_dma_get_soc_data(pdev); > > + if (!sdata) > > + return -EINVAL; > > + > > + s3cdma = devm_kzalloc(&pdev->dev, sizeof(*s3cdma), GFP_KERNEL); > > + if (!s3cdma) > > + return -ENOMEM; > > + > > + s3cdma->pdev = pdev; > > + s3cdma->pdata = pdata; > > + s3cdma->sdata = sdata; > > + > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > + s3cdma->base = devm_ioremap_resource(&pdev->dev, res); > > + if (IS_ERR(s3cdma->base)) > > + return PTR_ERR(s3cdma->base); > > + > > + s3cdma->phy_chans = devm_kzalloc(&pdev->dev, > > + sizeof(struct s3c24xx_dma_phy) * > > + pdata->num_phy_channels, > > + GFP_KERNEL); > > + if (!s3cdma->phy_chans) > > + return -ENOMEM; > > + > > + /* aquire irqs and clocks for all physical channels */ > > + for (i = 0; i < pdata->num_phy_channels; i++) { > > + struct s3c24xx_dma_phy *phy = &s3cdma->phy_chans[i]; > > + char clk_name[6]; > > + > > + phy->id = i; > > + phy->base = s3cdma->base + (i * sdata->stride); > > + phy->host = s3cdma; > > + > > + phy->irq = platform_get_irq(pdev, i); > > + if (phy->irq < 0) { > > + dev_err(&pdev->dev, "failed to get irq %d, err %d\n", > > + i, phy->irq); > > + continue; > > + } > > + > > + ret = devm_request_irq(&pdev->dev, phy->irq, s3c24xx_dma_irq, > > + 0, pdev->name, phy); > > + if (ret) { > > + dev_err(&pdev->dev, "Unable to request irq for > channel %d, error > %d\n", > > + i, ret); > > + continue; > > + } > > + > > + if (sdata->has_clocks) { > > + sprintf(clk_name, "dma.%d", i); > > + phy->clk = devm_clk_get(&pdev->dev, clk_name); > > + if (IS_ERR(phy->clk) && sdata->has_clocks) { > > + dev_err(&pdev->dev, "unable to aquire clock for > channel %d, > error > > %lu", + i, PTR_ERR(phy->clk)); > > + continue; > > + } > > + > > + ret = clk_prepare(phy->clk); > > + if (ret) { > > + dev_err(&pdev->dev, "clock for phy %d failed, > error %d\n", > > + i, ret); > > + continue; > > + } > > + } > > + > > + spin_lock_init(&phy->lock); > > + phy->valid = true; > > + > > + dev_dbg(&pdev->dev, "physical channel %d is %s\n", > > + i, s3c24xx_dma_phy_busy(phy) ? "BUSY" : "FREE"); > > + } > > + > > + /* Initialize memcpy engine */ > > + dma_cap_set(DMA_MEMCPY, s3cdma->memcpy.cap_mask); > > + dma_cap_set(DMA_PRIVATE, s3cdma->memcpy.cap_mask); > > + s3cdma->memcpy.dev = &pdev->dev; > > + s3cdma->memcpy.device_alloc_chan_resources = > > + s3c24xx_dma_alloc_chan_resources; > > + s3cdma->memcpy.device_free_chan_resources = > > + s3c24xx_dma_free_chan_resources; > > + s3cdma->memcpy.device_prep_dma_memcpy = s3c24xx_dma_prep_memcpy; > > + s3cdma->memcpy.device_tx_status = s3c24xx_dma_tx_status; > > + s3cdma->memcpy.device_issue_pending = s3c24xx_dma_issue_pending; > > + s3cdma->memcpy.device_control = s3c24xx_dma_control; > > + > > + /* Initialize slave engine for SoC internal dedicated peripherals > */ > > + dma_cap_set(DMA_SLAVE, s3cdma->slave.cap_mask); > > + dma_cap_set(DMA_PRIVATE, s3cdma->slave.cap_mask); > > + s3cdma->slave.dev = &pdev->dev; > > + s3cdma->slave.device_alloc_chan_resources = > > + s3c24xx_dma_alloc_chan_resources; > > + s3cdma->slave.device_free_chan_resources = > > + s3c24xx_dma_free_chan_resources; > > + s3cdma->slave.device_tx_status = s3c24xx_dma_tx_status; > > + s3cdma->slave.device_issue_pending = s3c24xx_dma_issue_pending; > > + s3cdma->slave.device_prep_slave_sg = s3c24xx_dma_prep_slave_sg; > > + s3cdma->slave.device_control = s3c24xx_dma_control; > > + > > + /* Register as many memcpy channels as there are physical channels > */ > > + ret = s3c24xx_dma_init_virtual_channels(s3cdma, &s3cdma->memcpy, > > + pdata->num_phy_channels, false); > > + if (ret <= 0) { > > + dev_warn(&pdev->dev, > > + "%s failed to enumerate memcpy channels - %d\n", > > + __func__, ret); > > + goto err_memcpy; > > + } > > + > > + /* Register slave channels */ > > + ret = s3c24xx_dma_init_virtual_channels(s3cdma, &s3cdma->slave, > > + pdata->num_channels, true); > > + if (ret <= 0) { > > + dev_warn(&pdev->dev, > > + "%s failed to enumerate slave channels - %d\n", > > + __func__, ret); > > + goto err_slave; > > + } > > + > > + ret = dma_async_device_register(&s3cdma->memcpy); > > + if (ret) { > > + dev_warn(&pdev->dev, > > + "%s failed to register memcpy as an async device - > %d\n", > > + __func__, ret); > > + goto err_memcpy_reg; > > + } > > + > > + ret = dma_async_device_register(&s3cdma->slave); > > + if (ret) { > > + dev_warn(&pdev->dev, > > + "%s failed to register slave as an async device - > %d\n", > > + __func__, ret); > > + goto err_slave_reg; > > + } > > + > > + platform_set_drvdata(pdev, s3cdma); > > + dev_info(&pdev->dev, "Loaded dma driver with %d physical > channels\n", > > + pdata->num_phy_channels); > > + > > + return 0; > > + > > +err_slave_reg: > > + dma_async_device_unregister(&s3cdma->memcpy); > > +err_memcpy_reg: > > + s3c24xx_dma_free_virtual_channels(&s3cdma->slave); > > +err_slave: > > + s3c24xx_dma_free_virtual_channels(&s3cdma->memcpy); > > +err_memcpy: > > + if (sdata->has_clocks) > > + for (i = 0; i < pdata->num_phy_channels; i++) { > > + struct s3c24xx_dma_phy *phy = &s3cdma->phy_chans[i]; > > + if (phy->valid) > > + clk_unprepare(phy->clk); > > + } > > + > > + return ret; > > +} > > + > > +static int s3c24xx_dma_remove(struct platform_device *pdev) > > +{ > > + const struct s3c24xx_dma_platdata *pdata = dev_get_platdata(&pdev- > >dev); > > + struct s3c24xx_dma_engine *s3cdma = platform_get_drvdata(pdev); > > + struct soc_data *sdata = s3c24xx_dma_get_soc_data(pdev); > > + int i; > > + > > + dma_async_device_unregister(&s3cdma->slave); > > + dma_async_device_unregister(&s3cdma->memcpy); > > + > > + s3c24xx_dma_free_virtual_channels(&s3cdma->slave); > > + s3c24xx_dma_free_virtual_channels(&s3cdma->memcpy); > > + > > + if (sdata->has_clocks) > > + for (i = 0; i < pdata->num_phy_channels; i++) { > > + struct s3c24xx_dma_phy *phy = &s3cdma->phy_chans[i]; > > + if (phy->valid) > > + clk_unprepare(phy->clk); > > + } > > + > > + return 0; > > +} > > + > > +static struct platform_driver s3c24xx_dma_driver = { > > + .driver = { > > + .name = "s3c24xx-dma", > > + .owner = THIS_MODULE, > > + }, > > + .id_table = s3c24xx_dma_driver_ids, > > + .probe = s3c24xx_dma_probe, > > + .remove = s3c24xx_dma_remove, > > +}; > > + > > +module_platform_driver(s3c24xx_dma_driver); > > + > > +bool s3c24xx_dma_filter(struct dma_chan *chan, void *param) > > +{ > > + struct s3c24xx_dma_chan *s3cchan; > > + > > + if (chan->device->dev->driver != &s3c24xx_dma_driver.driver) > > + return false; > > + > > + s3cchan = to_s3c24xx_dma_chan(chan); > > + > > + return s3cchan->id == (int)param; > > +} > > +EXPORT_SYMBOL(s3c24xx_dma_filter); > > + > > +MODULE_DESCRIPTION("S3C24XX DMA Driver"); > > +MODULE_AUTHOR("Heiko Stuebner"); > > +MODULE_LICENSE("GPL v2"); > > diff --git a/include/linux/platform_data/dma-s3c24xx.h > > b/include/linux/platform_data/dma-s3c24xx.h new file mode 100644 > > index 0000000..5a0cfff > > --- /dev/null > > +++ b/include/linux/platform_data/dma-s3c24xx.h > > @@ -0,0 +1,43 @@ > > +/* > > + * S3C24XX DMA handling > > + * > > + * Copyright (c) 2013 Heiko Stuebner <he...@sntech.de> > > + * > > + * This program is free software; you can redistribute it and/or modify > it > > + * under the terms of the GNU General Public License as published by > the > > Free + * Software Foundation; either version 2 of the License, or (at > your > > option) + * any later version. > > + */ > > + > > +enum s3c24xx_dma_bus { > > + S3C24XX_DMA_APB, > > + S3C24XX_DMA_AHB, > > +}; > > + > > +/** > > + * @bus: on which bus does the peripheral reside - AHB or APB. > > + * @handshake: is a handshake with the peripheral necessary > > + * @chansel: channel selection information, depending on variant; > reqsel > > for + * s3c2443 and later and channel-selection map for earlier > SoCs > > + * see CHANSEL doc in s3c2443-dma.c > > + */ > > +struct s3c24xx_dma_channel { > > + enum s3c24xx_dma_bus bus; > > + bool handshake; > > + u16 chansel; > > +}; > > + > > +/** > > + * struct s3c24xx_dma_platdata - platform specific settings > > + * @num_phy_channels: number of physical channels > > + * @channels: array of virtual channel descriptions > > + * @num_channels: number of virtual channels > > + */ > > +struct s3c24xx_dma_platdata { > > + int num_phy_channels; > > + struct s3c24xx_dma_channel *channels; > > + int num_channels; > > +}; > > + > > +struct dma_chan; > > +bool s3c24xx_dma_filter(struct dma_chan *chan, void *param); -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html