On Tuesday, October 08, 2013 8:45 PM, Yuvaraj Kumar wrote: > On Fri, Oct 4, 2013 at 6:03 AM, Jingoo Han <jg1....@samsung.com> wrote: > > On Thursday, October 03, 2013 8:32 PM, Bartlomiej Zolnierkiewicz wrote: > >> On Tuesday, October 01, 2013 12:03:01 PM Yuvaraj Kumar C D wrote: > >> > Exynos5250 contains one Synopsys AHCI SATA controller.The avalaible > >> > ahci_platform driver is not sufficient to handle the AHCI PHY and PHY > >> > clock related initialization. > >> > > >> > This patch adds exynos specific ahci sata driver,contained the exynos > >> > specific initialized codes, re-use the generic ahci_platform driver, and > >> > keep the generic ahci_platform driver clean as much as possible. > >> > > >> > This patch depends on the below patch > >> > [1].drivers: phy: add generic PHY framework > >> > by Kishon Vijay Abraham I<kis...@ti.com> > >> > > >> > Signed-off-by: Yuvaraj Kumar C D <yuvaraj...@samsung.com> > >> > --- > >> > drivers/ata/Kconfig | 9 ++ > >> > drivers/ata/Makefile | 1 + > >> > drivers/ata/ahci_exynos.c | 226 > >> > +++++++++++++++++++++++++++++++++++++++++++++ > >> > 3 files changed, 236 insertions(+) > >> > create mode 100644 drivers/ata/ahci_exynos.c > >> > > > > > > > [.....] > > > >> > + priv->phy = devm_phy_get(dev , "sata-phy"); > >> > + if (IS_ERR(priv->phy)) > >> > + return PTR_ERR(priv->phy); > > > > [.....] > > > >> Also please take a look at the following patch: > >> > >> https://lkml.org/lkml/2013/9/19/173 > >> > >> it adds PHY support to ahci_platform driver, maybe it can be used > >> for your needs as well. > > > > I also agree with Bartlomiej Zolnierkiewicz's opinion. > > 'ahci_exynos.c' just calls PHY API, without any additional control > > for Exynos AHCI IP. > In addition to PHY handling,it also deals with the special clock > sclk_sata which is not dealt in ahci_platform.c(certainly exynos > specific).
Handling the special clock 'sclk_sata' is another issue. Please, look at that other 'sclk_*'s are handled. Also, if possible, please add 'the code handling the special clock' to 'ahci_platform.c'. > > Morever there is a wrapper driver to handle the platform specific > things for the sata.Please refer the patch[1] > [1]ata: ti_sata: Add Texas Instruments SATA Wrapper driver > https://lkml.org/lkml/2013/9/19/166 As Roger Quadros mentioned, 'ti_sata' driver will be dropped. > [2]ahci_imx: add ahci sata support on imx platforms > 'ahci_imx' is necessary, because 'ahci_imx' controls some specific registers. However, 'ahci_exynos.c' does not control any registers. > I think, if we have platform specific driver like ahci_xxx.c , it > would be better to handle the sata PHY in ahci_xxx.c so that we can > retain and re-use the ahci_platform.c as it is. I think that the platform specific driver like ahci_xxx.c is not necessary, because 'ahci_exynos.c' does not control any special registers. Best regards, Jingoo Han > > Further comments will be much appreciated. > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html