On Sat, Jan 18, 2014 at 05:40:51PM +0530, Thomas Abraham wrote:
> From: Thomas Abraham <thomas...@samsung.com>
>
> On some platforms such as the Samsung Exynos, changing the frequency
> of the CPU clock requires changing the frequency of the PLL that is
> supplying the CPU clock. To change the frequency of the PLL, the CPU
> clock is temporarily reparented to another parent clock.
>
> The clock frequency of this temporary parent clock could be much higher
> than the clock frequency of the PLL at the time of reparenting. Due
> to the temporary increase in the CPU clock speed, the CPU (and any other
> components in the CPU clock domain such as dividers, mux, etc.) have to
> to be operated at a higher voltage level, called the safe voltage level.
> This patch adds optional support to temporarily switch to a safe voltage
> level during CPU frequency transitions.
>
> Cc: Shawn Guo <shawn....@linaro.org>
> Signed-off-by: Thomas Abraham <thomas...@samsung.com>
> ---
> .../devicetree/bindings/cpufreq/cpufreq-cpu0.txt | 7 ++++
The devicetree list should be copied for this change.
> drivers/cpufreq/cpufreq-cpu0.c | 37 +++++++++++++++++--
> 2 files changed, 40 insertions(+), 4 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> index f055515..37453ab 100644
> --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt
> @@ -19,6 +19,12 @@ Optional properties:
> - cooling-min-level:
> - cooling-max-level:
> Please refer to Documentation/devicetree/bindings/thermal/thermal.txt.
> +- safe-opp: Certain platforms require that during a opp transition,
> + a system should not go below a particular opp level. For such systems,
> + this property specifies the minimum opp to be maintained during the
> + opp transitions. The safe-opp value is a tuple with first element
> + representing the safe frequency and the second element representing the
> + safe voltage.
>
> Examples:
>
> @@ -36,6 +42,7 @@ cpus {
> 396000 950000
> 198000 850000
> >;
> + safe-opp = <396000 950000>
> clock-latency = <61036>; /* two CLK32 periods */
> #cooling-cells = <2>;
> cooling-min-level = <0>;
> diff --git a/drivers/cpufreq/cpufreq-cpu0.c b/drivers/cpufreq/cpufreq-cpu0.c
> index 0c12ffc..075d3d1 100644
> --- a/drivers/cpufreq/cpufreq-cpu0.c
> +++ b/drivers/cpufreq/cpufreq-cpu0.c
> @@ -27,6 +27,8 @@
>
> static unsigned int transition_latency;
> static unsigned int voltage_tolerance; /* in percentage */
> +static unsigned long safe_frequency;
> +static unsigned long safe_voltage;
>
> static struct device *cpu_dev;
> static struct clk *cpu_clk;
> @@ -64,17 +66,30 @@ static int cpu0_set_target(struct cpufreq_policy *policy,
> unsigned int index)
> volt_old = regulator_get_voltage(cpu_reg);
> }
>
> - pr_debug("%u MHz, %ld mV --> %u MHz, %ld mV\n",
> + pr_debug("\n\n%u MHz, %ld mV --> %u MHz, %ld mV\n",
This is an unnecessary change?
Otherwise,
Acked-by: Shawn Guo <shawn....@linaro.org>
Shawn
> old_freq / 1000, volt_old ? volt_old / 1000 : -1,
> new_freq / 1000, volt ? volt / 1000 : -1);
>
> /* scaling up? scale voltage before frequency */
> - if (!IS_ERR(cpu_reg) && new_freq > old_freq) {
> + if (!IS_ERR(cpu_reg) && new_freq > old_freq &&
> + new_freq >= safe_frequency) {
> ret = regulator_set_voltage_tol(cpu_reg, volt, tol);
> if (ret) {
> pr_err("failed to scale voltage up: %d\n", ret);
> return ret;
> }
> + } else if (!IS_ERR(cpu_reg) && old_freq < safe_frequency) {
> + /*
> + * the scaled up voltage level for the new_freq is lower
> + * than the safe voltage level. so set safe_voltage
> + * as the intermediate voltage level and revert it
> + * back after the frequency has been changed.
> + */
> + ret = regulator_set_voltage_tol(cpu_reg, safe_voltage, tol);
> + if (ret) {
> + pr_err("failed to set safe voltage: %d\n", ret);
> + return ret;
> + }
> }
>
> ret = clk_set_rate(cpu_clk, freq_exact);
> @@ -86,7 +101,8 @@ static int cpu0_set_target(struct cpufreq_policy *policy,
> unsigned int index)
> }
>
> /* scaling down? scale voltage after frequency */
> - if (!IS_ERR(cpu_reg) && new_freq < old_freq) {
> + if (!IS_ERR(cpu_reg) &&
> + (new_freq < old_freq || new_freq < safe_frequency)) {
> ret = regulator_set_voltage_tol(cpu_reg, volt, tol);
> if (ret) {
> pr_err("failed to scale voltage down: %d\n", ret);
> @@ -116,6 +132,8 @@ static struct cpufreq_driver cpu0_cpufreq_driver = {
>
> static int cpu0_cpufreq_probe(struct platform_device *pdev)
> {
> + const struct property *prop;
> + struct dev_pm_opp *opp;
> struct device_node *np;
> int ret;
>
> @@ -165,13 +183,24 @@ static int cpu0_cpufreq_probe(struct platform_device
> *pdev)
> goto out_put_node;
> }
>
> + prop = of_find_property(np, "safe-opp", NULL);
> + if (prop) {
> + if (prop->value && (prop->length / sizeof(u32)) == 2) {
> + const __be32 *val;
> + val = prop->value;
> + safe_frequency = be32_to_cpup(val++);
> + safe_voltage = be32_to_cpup(val);
> + } else {
> + pr_err("invalid safe-opp level specified\n");
> + }
> + }
> +
> of_property_read_u32(np, "voltage-tolerance", &voltage_tolerance);
>
> if (of_property_read_u32(np, "clock-latency", &transition_latency))
> transition_latency = CPUFREQ_ETERNAL;
>
> if (!IS_ERR(cpu_reg)) {
> - struct dev_pm_opp *opp;
> unsigned long min_uV, max_uV;
> int i;
>
> --
> 1.6.6.rc2
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
