Hi Tomasz,
On 04/08/2014 04:37 PM, Tomasz Stanislawski wrote:
> Add exynos-simple-phy driver to support a single register
> PHY interfaces present on Exynos4 SoC.
>
> Signed-off-by: Tomasz Stanislawski <t.stanisl...@samsung.com>
> ---
> .../devicetree/bindings/phy/samsung-phy.txt | 24 +++
> drivers/phy/Kconfig | 5 +
> drivers/phy/Makefile | 1 +
> drivers/phy/exynos-simple-phy.c | 154
> ++++++++++++++++++++
> 4 files changed, 184 insertions(+)
> create mode 100644 drivers/phy/exynos-simple-phy.c
>
> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> index b422e38..f97c4c3 100644
> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
> @@ -114,3 +114,27 @@ Example:
> compatible = "samsung,exynos-sataphy-i2c";
> reg = <0x38>;
> };
> +
> +Samsung S5P/EXYNOS SoC series SIMPLE PHY
> +-------------------------------------------------
> +
> +Required properties:
> +- compatible : should be one of the listed compatibles:
> + - "samsung,exynos4210-simple-phy"
> + - "samsung,exynos4412-simple-phy"
> +- reg : offset and length of the register set;
> +- #phy-cells : from the generic phy bindings, must be 1;
> +
> +For "samsung,exynos4210-simple-phy" compatible PHYs the second cell in
> +the PHY specifier identifies the PHY and its meaning is as follows:
> + 0 - HDMI PHY,
> + 1 - DAC PHY,
> + 2 - ADC PHY,
> + 3 - PCIE PHY.
> + 4 - SATA PHY.
> +
> +For "samsung,exynos4412-simple-phy" compatible PHYs the second cell in
> +the PHY specifier identifies the PHY and its meaning is as follows:
> + 0 - HDMI PHY,
> + 1 - ADC PHY,
What about using preprocessor macros?
> +
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 3bb05f1..65ab783 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -166,4 +166,9 @@ config PHY_XGENE
> help
> This option enables support for APM X-Gene SoC multi-purpose PHY.
>
> +config EXYNOS_SIMPLE_PHY
> + tristate "Exynos Simple PHY driver"
> + help
> + Support for 1-bit PHY controllers on SoCs from Exynos family.
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 2faf78e..88c5b60 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -18,3 +18,4 @@ obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
> obj-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o
> obj-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
> obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
> +obj-$(CONFIG_EXYNOS_SIMPLE_PHY) += exynos-simple-phy.o
> diff --git a/drivers/phy/exynos-simple-phy.c b/drivers/phy/exynos-simple-phy.c
> new file mode 100644
> index 0000000..57ad338
> --- /dev/null
> +++ b/drivers/phy/exynos-simple-phy.c
> @@ -0,0 +1,154 @@
> +/*
> + * Exynos Simple PHY driver
> + *
> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> + * Author: Tomasz Stanislawski <t.stanisl...@samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +
> +#define EXYNOS_PHY_ENABLE (1 << 0)
> +
> +static int exynos_phy_power_on(struct phy *phy)
> +{
> + void __iomem *reg = phy_get_drvdata(phy);
> + u32 val;
> +
> + val = readl(reg);
> + val |= EXYNOS_PHY_ENABLE;
> + writel(val, reg);
> +
> + return 0;
> +}
> +
> +static int exynos_phy_power_off(struct phy *phy)
> +{
> + void __iomem *reg = phy_get_drvdata(phy);
> + u32 val;
> +
> + val = readl(reg);
> + val &= ~EXYNOS_PHY_ENABLE;
> + writel(val, reg);
> +
> + return 0;
> +}
> +
> +static struct phy_ops exynos_phy_ops = {
> + .power_on = exynos_phy_power_on,
> + .power_off = exynos_phy_power_off,
> + .owner = THIS_MODULE,
> +};
> +
> +static const u32 exynos4210_offsets[] = {
> + 0x0700, /* HDMI_PHY */
> + 0x070C, /* DAC_PHY */
> + 0x0718, /* ADC_PHY */
> + 0x071C, /* PCIE_PHY */
> + 0x0720, /* SATA_PHY */
> + ~0, /* end mark */
> +};
> +
> +static const u32 exynos4412_offsets[] = {
> + 0x0700, /* HDMI_PHY */
> + 0x0718, /* ADC_PHY */
> + ~0, /* end mark */
> +};
Why have you selected only these registers?
According to specs Exynos 4210 has 9 and 4412 has 7 control registers
with 'phy-enable' functionality.
I guess MIPI would require little more work as it has also reset bits,
but it will be still better than separate driver.
> +
> +static const struct of_device_id exynos_phy_of_match[] = {
> + { .compatible = "samsung,exynos4210-simple-phy",
> + .data = exynos4210_offsets},
> + { .compatible = "samsung,exynos4412-simple-phy",
> + .data = exynos4412_offsets},
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, exynos_phy_of_match);
> +
> +static struct phy *exynos_phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct phy **phys = dev_get_drvdata(dev);
> + int index = args->args[0];
> + int i;
> +
> + /* verify if index is valid */
> + for (i = 0; i <= index; ++i)
> + if (!phys[i])
> + return ERR_PTR(-ENODEV);
> +
> + return phys[index];
> +}
> +
> +static int exynos_phy_probe(struct platform_device *pdev)
> +{
> + const struct of_device_id *of_id = of_match_device(
> + of_match_ptr(exynos_phy_of_match), &pdev->dev);
> + const u32 *offsets = of_id->data;
> + int count;
> + struct device *dev = &pdev->dev;
> + struct phy **phys;
> + struct resource *res;
> + void __iomem *regs;
> + int i;
> + struct phy_provider *phy_provider;
> +
> + /* count number of phys to create */
> + for (count = 0; offsets[count] != ~0; ++count)
> + ;
count = ARRAY_SIZE(offsets) - 1;
> +
> + phys = devm_kzalloc(dev, (count + 1) * sizeof(phys[0]), GFP_KERNEL);
> + if (!phys)
> + return -ENOMEM;
> +
> + dev_set_drvdata(dev, phys);
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
> + regs = devm_ioremap(dev, res->start, res->end - res->start);
> + if (!regs) {
> + dev_err(dev, "failed to ioremap registers\n");
> + return -EFAULT;
> + }
Why not devm_ioremap_resource? If not, resource_size function calculates
length of resource correctly.
Anyway I like the idea of implementing multiple phys in one driver.
The only drawback I see is that some phys will be created even there are
no consumers for them. To avoid such situation you can try to use
lazy approach - create phy only if there is request for it,
exynos_phy_xlate callback should allow this.
Regards
Andrzej
> +
> + /* NOTE: last entry in phys[] is NULL */
> + for (i = 0; i < count; ++i) {
> + phys[i] = devm_phy_create(dev, &exynos_phy_ops, NULL);
> + if (IS_ERR(phys[i])) {
> + dev_err(dev, "failed to create PHY %d\n", i);
> + return PTR_ERR(phys[i]);
> + }
> + phy_set_drvdata(phys[i], regs + offsets[i]);
> + }
> +
> + phy_provider = devm_of_phy_provider_register(dev, exynos_phy_xlate);
> + if (IS_ERR(phy_provider)) {
> + dev_err(dev, "failed to register PHY provider\n");
> + return PTR_ERR(phy_provider);
> + }
> +
> + dev_info(dev, "added %d phys\n", count);
> +
> + return 0;
> +}
> +
> +static struct platform_driver exynos_phy_driver = {
> + .probe = exynos_phy_probe,
> + .driver = {
> + .of_match_table = exynos_phy_of_match,
> + .name = "exynos-simple-phy",
> + .owner = THIS_MODULE,
> + }
> +};
> +module_platform_driver(exynos_phy_driver);
> +
> +MODULE_DESCRIPTION("Exynos Simple PHY driver");
> +MODULE_AUTHOR("Tomasz Stanislawski <t.stanisl...@samsung.com>");
> +MODULE_LICENSE("GPL v2");
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
