Am 26.06.2014 20:15, schrieb Javier Martinez Canillas:
> Add Device Tree binding documentation for Maxim 77802 PMIC.
>
> Signed-off-by: Javier Martinez Canillas <javier.marti...@collabora.co.uk>
> ---
>
> Changes since v4: None
>
> Changes since v3: None
>
> Changes since v2:
> - Explain better the Dynamic Voltage Scaling (DVS) support in some Buck
> regulators and the max77802,pmic-buck-{dvs,selb}-gpios properties.
> Suggested by Mark Brown.
>
> Documentation/devicetree/bindings/mfd/max77802.txt | 97
> ++++++++++++++++++++++
> 1 file changed, 97 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/max77802.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/max77802.txt
> b/Documentation/devicetree/bindings/mfd/max77802.txt
> new file mode 100644
> index 0000000..f3b67c5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/max77802.txt
> @@ -0,0 +1,97 @@
> +Maxim MAX77802 multi-function device
> +
> +MAX77802 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is
"Multifunction"?
> +interfaced to host controller using i2c interface. PMIC, Charger and RTC
> +submodules are addressed using same i2c slave address.
> +
> +Buck regulators 1, 2, 3, 4 and 6 include Dynamic Voltage Scaling (DVS) that
> +allows each output voltage to change dynamically. Each Buck output voltage
> +is selected using a set of external inputs: DVS1-3 and SELB1, 2, 3 and 6.
> +
> +There are 8 DVS registers that can be used to configure the output voltage
> +for each Buck regulator and which one is active is controled by DVSx lines.
> +
> +SELBx lines are used to control if individual Buck lines are ON or OFF.
> +
> +This document describes the binding for mfd device and PMIC submodule.
> +
> +Binding for the built-in 32k clock generator block is defined separately
> +in bindings/clk/maxim,max77802.txt file.
> +
> +Required properties:
> +- compatible : Must be "maxim,max77802";
> +- reg : Specifies the i2c slave address of PMIC block.
> +- interrupts : This i2c device has an IRQ line connected to the main SoC.
> +- interrupt-parent : The parent interrupt controller.
> +
> +Optional properties:
> +- max77802,pmic-buck-default-dvs-idx: We'll always write this DVS index in
> the
> + PMIC for Bucks with DVS.
> + NOTE: at the moment these bindings don't include enough details for actual
> + GPIO-DVS--this just lets you choose which single slot to use.
> +
> +- max77802,pmic-buck-dvs-gpios: A GPIO array where each GPIO is connected to
> a
> + DVS line. We'll try to set these GPIOs to match pmic-buck-default-dvs-idx
> at
> + probe time if they are defined. If some or all of these GPIOs are not
> defined
> + it's assumed that the board has any missing GPIOs hardwired to match
> + pmic-buck-default-dvs-idx.
> +
> +- max77802,pmic-buck-selb-gpios: A GPIO array where each GPIO is connected
> to a
> + SELBx line. Should be five values: 1, 2, 3, 4, 6. It is strongly suggested
> to
> + include these GPIOs if there's any chance that changing DVS GPIOs one line
> at
> + a time might glitch your DVS values.
> +
> +Optional node:
> +- regulators : The regulators of max77802 have to be instantiated
> + under subnode named "regulators" using the following format.
> +
> + regulator_name {
The convention, I was told, would be regulator-name as node name.
> + standard regulator constraints....
> + };
> + refer Documentation/devicetree/bindings/regulator/regulator.txt
> +
> + The regulator node name should be initialized with a string
> +to get matched with their hardware counterparts as follow:
> +
> + -LDOn : for LDOs, where n can lie in range 1 to 35.
> + example: LDO1, LDO2, LDO35.
> + -BUCKn : for BUCKs, where n can lie in range 1 to 10.
> + example: BUCK1, BUCK5, BUCK10.
> +Example:
> +
> + max77802@09 {
> + compatible = "maxim,max77802";
> + interrupt-parent = <&wakeup_eint>;
> + interrupts = <26 0>;
> + reg = <0x09>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + max77802,pmic-buck-default-dvs-idx = <1>;
> + max77802,pmic-buck-dvs-gpios = <&gpy7 6 0>,
> + <&gpj4 2 0>,
> + <&gpj4 3 0>;
> + max77802,pmic-buck-selb-gpios = <&gph0 2 0>,
> + <&gph0 3 0>,
> + <&gph0 4 0>,
> + <&gph0 5 0>,
> + <&gph0 6 0>;
> +
> + regulators {
> + ldo11_reg: LDO11 {
> + regulator-compatible = "LDO11";
> + regulator-name = "vdd_ldo11";
> + regulator-min-microvolt = <1900000>;
> + regulator-max-microvolt = <1900000>;
> + regulator-always-on;
> + };
> +
> + buck1_reg {
Missing ": BUCK1"
> + regulator-compatible = "BUCK1";
> + regulator-name = "vdd_mif";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> + };
Regards,
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
