On Wed, 03 Oct 2007 12:47:26 -0700 Seokmann Ju <[EMAIL PROTECTED]> wrote:
> FUJITA Tomonori wrote: > > On Mon, 01 Oct 2007 11:00:44 -0700 > > Seokmann Ju <[EMAIL PROTECTED]> wrote: > >> atl-01:/lib/modules/2.6.23-rc3-smp-tgt/kernel/drivers/scsi/qla2xxx # > >> tgtadm --lld fc --mode target --op show > >> Target 1: volume1 > >> System information: > >> Driver: fc > >> Status: running > >> I_T nexus information: > >> LUN information: > >> LUN: 0 > >> Type: controller > >> SCSI ID: deadbeaf1:0 > >> SCSI SN: beaf10 > >> Size: 0 > >> Online: No > >> Poweron/Reset: Yes > >> Removable media: No > >> Backing store: No backing store > >> ACL information: > > > > You successfully created a new target but failed to add a new logical > > unit (#1) to it (note that lun 0 was created automatically). > Yes, I have noticed it. > > >>> ./tgt/usr/tgtadm --lld fc --mode logicalunit --op new --tid 1 --lun 1 -b > >>> /var/tmp/lun1 > > > > We are try to add a regular file (/var/tmp/lun1) to the target and > > export it as a logical unit to initiators. Do you have /var/tmp/lun1? > With the creation of an empty file, it started to display the lun1. > --- > atl-01:~ # tgtadm --lld fc --mode target --op show > Target 1: tgt-vol1 > System information: > Driver: fc > Status: running > I_T nexus information: > I_T nexus: f6fb6000 The target got an initiator. Can you setup a target first (all the initiators are shut down (or fc kernel modules in initiators hosts are unloaded). There is no I_T nexus in the show operation's output. Then you start initiator hosts (or load the kernel modules) and hopefully the initiator hots can see luns. > LUN information: > LUN: 0 > Type: controller > SCSI ID: deadbeaf1:0 > SCSI SN: beaf10 > Size: 0 > Online: No > Poweron/Reset: Yes > Removable media: No > Backing store: No backing store > LUN: 1 > Type: disk > SCSI ID: deadbeaf1:1 > SCSI SN: beaf11 > Size: 0 Note 'Size: 0' line. Needs to use a non-empty file. > Online: Yes > Poweron/Reset: Yes > Removable media: No > Backing store: /var/tmp/lun1 > ACL information: > atl-01:~ # > --- > > However, from the initiator, still not be able to see the target - from the > lsscsi, no other devices (controller/virtual-disk) than those physical > devices available on the fabric. > Instead, the host with target-mode displays following messages, > --- > Oct 3 11:21:13 atl-01 kernel: q2t_it_nexus_response 1191: dff46400 0 > Oct 3 11:21:13 atl-01 kernel: q2t_it_nexus_response 1191: dff46400 0 It means that user-space daemon (tgtd) sent a message that a new I_T nexus was created. > > If I understood correctly, the F/W on the host with target-mode should have > gotten some SCSI commands from the host with initiator-mode by now. > And those commands should have been forwarded to the target driver via the > interrupt handler (qla24xx_intr_handler()). Yeah, I think so. > Just for my learning, could you share with me which of the F/W version (on > the target-mode QLogic FC HBA) you are using? qla2xxx 0000:0a:02.0: QLogic Fibre Channel HBA Driver: 8.02.00-k2 QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel ISP2312: PCI-X (133 MHz) @ 0000:0a:02.0 hdma-, host#=3, fw=3.03.20 IPX - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html
