Hi Tomas,
Thanks for your review comments.
I have used sslep(10) instead udelay in this patch.
Hi James,
Patch description:
This patch adds dual flash firmware support for Series 7 and above controllers.
Regards,
Mahesh
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekh...@pmcs.com>
---
drivers/scsi/aacraid/aacraid.h | 6 +++++-
drivers/scsi/aacraid/comminit.c | 2 +-
drivers/scsi/aacraid/src.c | 26 +++++++++++++++++++++++++-
3 files changed, 31 insertions(+), 3 deletions(-)
diff --git a/drivers/scsi/aacraid/aacraid.h b/drivers/scsi/aacraid/aacraid.h
index a6f7190..9323d05 100644
--- a/drivers/scsi/aacraid/aacraid.h
+++ b/drivers/scsi/aacraid/aacraid.h
@@ -12,7 +12,7 @@
*----------------------------------------------------------------------------*/
#ifndef AAC_DRIVER_BUILD
-# define AAC_DRIVER_BUILD 30000
+# define AAC_DRIVER_BUILD 30200
# define AAC_DRIVER_BRANCH "-ms"
#endif
#define MAXIMUM_NUM_CONTAINERS 32
@@ -1918,6 +1918,10 @@ extern struct aac_common aac_config;
#define MONITOR_PANIC 0x00000020
#define KERNEL_UP_AND_RUNNING 0x00000080
#define KERNEL_PANIC 0x00000100
+#define FLASH_UPD_PENDING 0x00002000
+#define FLASH_UPD_SUCCESS 0x00004000
+#define FLASH_UPD_FAILED 0x00008000
+#define FWUPD_TIMEOUT (5 * 60)
/*
* Doorbell bit defines
diff --git a/drivers/scsi/aacraid/comminit.c b/drivers/scsi/aacraid/comminit.c
index 3f75995..177b094 100644
--- a/drivers/scsi/aacraid/comminit.c
+++ b/drivers/scsi/aacraid/comminit.c
@@ -214,7 +214,7 @@ int aac_send_shutdown(struct aac_dev * dev)
cmd = (struct aac_close *) fib_data(fibctx);
cmd->command = cpu_to_le32(VM_CloseAll);
- cmd->cid = cpu_to_le32(0xffffffff);
+ cmd->cid = cpu_to_le32(0xfffffffe);
status = aac_fib_send(ContainerCommand,
fibctx,
diff --git a/drivers/scsi/aacraid/src.c b/drivers/scsi/aacraid/src.c
index e2e3492..0f56d8d 100644
--- a/drivers/scsi/aacraid/src.c
+++ b/drivers/scsi/aacraid/src.c
@@ -703,6 +703,28 @@ int aac_srcv_init(struct aac_dev *dev)
!aac_src_restart_adapter(dev, 0))
++restart;
/*
+ * Check to see if flash update is running.
+ * Wait for the adapter to be up and running. Wait up to 5 minutes
+ */
+ status = src_readl(dev, MUnit.OMR);
+ if (status & FLASH_UPD_PENDING) {
+ start = jiffies;
+ do {
+ status = src_readl(dev, MUnit.OMR);
+ if (time_after(jiffies, start+HZ*FWUPD_TIMEOUT)) {
+ printk(KERN_ERR "%s%d: adapter flash update
failed.\n",
+ dev->name, instance);
+ goto error_iounmap;
+ }
+ } while (!(status & FLASH_UPD_SUCCESS) &&
+ !(status & FLASH_UPD_FAILED));
+ /* Delay 10 seconds.
+ * Because right now FW is doing a soft reset,
+ * do not read scratch pad register at this time
+ */
+ ssleep(10);
+ }
+ /*
* Check to see if the board panic'd while booting.
*/
status = src_readl(dev, MUnit.OMR);
@@ -730,7 +752,9 @@ int aac_srcv_init(struct aac_dev *dev)
/*
* Wait for the adapter to be up and running. Wait up to 3 minutes
*/
- while (!((status = src_readl(dev, MUnit.OMR)) & KERNEL_UP_AND_RUNNING))
{
+ while (!((status = src_readl(dev, MUnit.OMR)) &
+ KERNEL_UP_AND_RUNNING) ||
+ status == 0xffffffff) {
if ((restart &&
(status & (KERNEL_PANIC|SELF_TEST_FAILED|MONITOR_PANIC))) ||
time_after(jiffies, start+HZ*startup_timeout)) {
--
1.7.7.6
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
