On Sat, Nov 30, 2013 at 04:42:02PM -0800, James Bottomley wrote:
> On Fri, 2013-11-08 at 09:31 -0600, scame...@beardog.cce.hp.com wrote:
> > On Fri, Nov 08, 2013 at 04:02:20PM +0100, Tomas Henzl wrote:
> > > On 11/08/2013 03:44 PM, scame...@beardog.cce.hp.com wrote:
> > > > On Fri, Nov 08, 2013 at 02:51:37PM +0100, Tomas Henzl wrote:
> > > >> On 11/07/2013 05:45 PM, Stephen M. Cameron wrote:
> > > >>> From: Stephen M. Cameron <scame...@beardog.cce.hp.com>
> > > >>>
> > > >>> The hardware guys tell us that after initiating a software
> > > >>> reset via the doorbell register we need to wait 5 seconds before
> > > >>> attempting to talk to the board *at all*. This means that we
> > > >>> cannot watch the board to verify it transitions from "ready" to
> > > >>> to "not ready" then back "ready", since this transition will
> > > >>> most likely happen during those 5 seconds (though we can still
> > > >>> verify the reset happens by watching the "driver version" field
> > > >>> get cleared.)
> > > >>>
> > > >>> Signed-off-by: Stephen M. Cameron <scame...@beardog.cce.hp.com>
> > > >>> ---
> > > >>> drivers/scsi/hpsa.c | 32 +++++++++++++++++++++++---------
> > > >>> 1 files changed, 23 insertions(+), 9 deletions(-)
> > > >>>
> > > >>> diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
> > > >>> index 20fc598..fff5fd3 100644
> > > >>> --- a/drivers/scsi/hpsa.c
> > > >>> +++ b/drivers/scsi/hpsa.c
> > > >>> @@ -3781,6 +3781,13 @@ static int hpsa_controller_hard_reset(struct
> > > >>> pci_dev *pdev,
> > > >>> */
> > > >>> dev_info(&pdev->dev, "using doorbell to reset
> > > >>> controller\n");
> > > >>> writel(use_doorbell, vaddr + SA5_DOORBELL);
> > > >>> +
> > > >>> + /* PMC hardware guys tell us we need a 5 second delay
> > > >>> after
> > > >>> + * doorbell reset and before any attempt to talk to the
> > > >>> board
> > > >>> + * at all to ensure that this actually works and
> > > >>> doesn't fall
> > > >>> + * over in some weird corner cases.
> > > >>> + */
> > > >>> + msleep(5000);
> > > >>> } else { /* Try to do it the PCI power state way */
> > > >>>
> > > >>> /* Quoting from the Open CISS Specification: "The Power
> > > >>> @@ -3977,15 +3984,22 @@ static int
> > > >>> hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
> > > >>> need a little pause here */
> > > >>> msleep(HPSA_POST_RESET_PAUSE_MSECS);
> > > >> I know it's complicated with a lot of different devices and fw
> > > >> versions,
> > > >> but here^ we wait for 3sec - isn't the method - wait for 3s then wait
> > > >> for board not ready
> > > >> a bit fragile, what if a board comes up faster?
> > > >> When the method "watching the "driver version"" works why don't you
> > > >> want to use it
> > > >> regardless of the reset method used?
> > > > The "watching the driver version" thing is only there to catch if
> > > > the firmware guys break things and turn the reset into a no-op
> > > > (which happened with the PCI power manaegment based reset and we
> > > > didn't catch it for a year or so because we didn't have that check)
> > > >
> > > > We aren't supposed to look at the driver version field (or anything)
> > > > until we first verify the scratch pad register says the firmware is
> > > > ready. In the case of those boards that use the "doorbell" reset,
> > > > we aren't supposed to look at *anything* for the first five seconds.
> > > >
> > > > I have been bugging the firmware/hardware guys for a sane reset
> > > > procedure that actually works reliably for years with no luck.
> > > >
> > > > For the SCSI over PCIe driver, being tired of this crap, I simply
> > > > unconditionally reset the device on driver load every single time,
> > > > and did this from the beginning. This kind of forced the firmware
> > > > and hardware guys to make the reset on that thing work reliably
> > > > and quickly, and since I did that from the earliest days, they didn't
> > > > have a chance to screw it up without it being caught immediately.
> > > > For Smart Array, obviously it's too late for that approach.
> > >
> > > OK, my question was more or less if this:
> > > msleep(HPSA_POST_RESET_PAUSE_MSECS);
> > > just before waiting for the board to enter BOARD_NOT_READY state
> > > isn't dangerous - when the board enters a ready state in the first 3sec
> > > it will wait indefinitely for the not_ready state
> > > thus whether the test for not ready state shouldn't be removed.
> > > The mechanism now works somehow and maybe it's better
> > > not to touch it, I just wanted to draw your attention to that
> > > potential problem.
> >
> > Oh ok, I see. Thanks, yes that does look questionable. So you
> > are suggesting to skip the check for transition from NOT READY to
> > READY in the scratch pad register in all cases, since we have all
> > these ridiculous delay requirements preventing us from watching the
> > board closely enough and so that may mean that we would miss such a
> > transition.
> >
> > Let me talk it over with Mike Miller, but it seems reasonable.
>
> Is there a resolution on this? It's holding up the patch series.
>
> James
>
James,
Let's omit the check for board ready/not ready. With these arbitrary delays
already in place we're likely to miss the transition.
Do you need me to resubmit the patch set?
-- mikem
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
