On 08/13/2014 10:24 PM, scame...@beardog.cce.hp.com wrote: > Let me try again, this time not from gmail. > > On Thu, Jun 12, 2014 at 10:29 AM, Tomas Henzl <the...@redhat.com> wrote: >> When a second(kdump) kernel starts and the hard reset method is used >> the driver calls pci_disable_device without previously enabling it, >> so the kernel shows a warning - >> [ 16.876248] WARNING: at drivers/pci/pci.c:1431 >> pci_disable_device+0x84/0x90() >> [ 16.882686] Device hpsa >> disabling already-disabled device >> ... >> This patch fixes it, in addition to this I tried to balance also some >> other pairs >> of enable/disable device in the driver. >> Unfortunately I wasn't able to verify the functionality for the case of a >> sw reset, >> because of a lack of proper hw. >> >> Signed-off-by: Tomas Henzl <the...@redhat.com> >> --- >> diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c >> index 5858600..67c41b9 100644 >> --- a/drivers/scsi/hpsa.c >> +++ b/drivers/scsi/hpsa.c >> @@ -5983,7 +5983,6 @@ static int hpsa_kdump_hard_reset_controller(struct >> pci_dev *pdev) >> /* Turn the board off. This is so that later pci_restore_state() >> * won't turn the board on before the rest of config space is >> ready. >> */ >> - pci_disable_device(pdev); >> pci_save_state(pdev); >> >> /* find the first memory BAR, so we can find the cfg table */ >> @@ -6031,11 +6030,6 @@ static int hpsa_kdump_hard_reset_controller(struct >> pci_dev *pdev) >> goto unmap_cfgtable; >> >> pci_restore_state(pdev); >> - rc = pci_enable_device(pdev); >> - if (rc) { >> - dev_warn(&pdev->dev, "failed to enable device.\n"); >> - goto unmap_cfgtable; >> - } >> pci_write_config_word(pdev, 4, command_register); >> >> /* Some devices (notably the HP Smart Array 5i Controller) >> @@ -6548,6 +6542,12 @@ static int hpsa_init_reset_devices(struct pci_dev >> *pdev) >> if (!reset_devices) >> return 0; >> >> + rc = pci_enable_device(pdev); >> + if (rc) { >> + dev_warn(&pdev->dev, "failed to enable device.\n"); >> + return -ENODEV; >> + } >> + >> /* Reset the controller with a PCI power-cycle or via doorbell */ >> rc = hpsa_kdump_hard_reset_controller(pdev); >> >> @@ -6556,10 +6556,11 @@ static int hpsa_init_reset_devices(struct pci_dev >> *pdev) >> * "performant mode". Or, it might be 640x, which can't reset >> * due to concerns about shared bbwc between 6402/6404 pair. >> */ >> - if (rc == -ENOTSUPP) >> - return rc; /* just try to do the kdump anyhow. */ >> - if (rc) >> - return -ENODEV; >> + if (rc) { >> + if (rc != -ENOTSUPP) /* just try to do the kdump anyhow. */ >> + rc = -ENODEV; >> + goto out_disable; >> > > Checkpatch complained of trailing whitespace here. ^^^
And we should remove the comment "/* Turn the board off..." which is not correct now. I'll repost the patch. We also might try to solve the problem that we don't know in which state the pci interface is when the driver starts in the kdump kernel. We could try something like pci_enable+disable at the start so it is switched off and the driver starts from the same point as if were switched off by bios. (Maybe it's done already somewhere and I'm just not able to find it though.) tomash > > Other than that, looks good. > > -- steve > > >> + } >> >> /* Now try to get the controller to respond to a no-op */ >> dev_warn(&pdev->dev, "Waiting for controller to respond to >> no-op\n"); >> @@ -6570,7 +6571,11 @@ static int hpsa_init_reset_devices(struct pci_dev >> *pdev) >> dev_warn(&pdev->dev, "no-op failed%s\n", >> (i < 11 ? "; re-trying" : "")); >> } >> - return 0; >> + >> +out_disable: >> + >> + pci_disable_device(pdev); >> + return rc; >> } >> >> static int hpsa_allocate_cmd_pool(struct ctlr_info *h) >> @@ -6722,6 +6727,7 @@ static void >> hpsa_undo_allocations_after_kdump_soft_reset(struct ctlr_info *h) >> iounmap(h->transtable); >> if (h->cfgtable) >> iounmap(h->cfgtable); >> + pci_disable_device(h->pdev); >> pci_release_regions(h->pdev); >> kfree(h); >> } >> -- >> 1.8.3.1 >> >> > ----- End forwarded message ----- > -- > To unsubscribe from this list: send the line "unsubscribe linux-scsi" in > the body of a message to majord...@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html