Instances of var * HZ / 1000 are replaced by msecs_to_jiffies(var).
In addition some timing constants that assumed HZ 100 were adjusted
to HZ independent settings based on review comments from Michael Schmitz
<schmitz...@gmail.com> and review of the original drivers in 1.0.31 and
2.2.16.
Signed-off-by: Nicholas Mc Guire <hof...@osadl.org>
---
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
ok but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly.
v2: The original patch was not taking care of all the dependencies
as reported by Finn Thain <fth...@telegraphics.com.au> - this
version now uses the suggested config to check the patch.
v3: g_NCR5380.c changes fixed up based on feedback from Michael Schmitz
<schmitz...@gmail.com> as these settings were from around 1.0.31
kernel (or earlier) where HZ was 100 only - thus the unit here is
actually 10s of microseconds. This was "verified" by checking the
setting changes against 2.2.16 indicating that it was forgotten in
1998/99.
v4: Sync changed with atari_NCR5380.c as well as correct the patch
description as suggested by Finn Thain <fth...@telegraphics.com.au>
This patch was only compile tested with i386_defconfig + CONFIG_ISA=y
as well as all (except CONFIG_SCSI_ATARI) drivers enabled as modules:
CONFIG_SCSI_LOWLEVEL=y, CONFIG_SCSI_GENERIC_NCR5380=m
CONFIG_SCSI_DMX3191D=m, CONFIG_SCSI_DTC3280=m
CONFIG_SCSI_GENERIC_NCR5380=m, CONFIG_SCSI_GENERIC_NCR5380_MMIO=m
CONFIG_SCSI_PAS16=m, CONFIG_SCSI_T128=m
Note that the change to atari_NCR5380.c was not even compile-tested
(crosstool-ng m68k-unknown-elf and m68k-unknown-uclinux-uclibc fail to
build atari_defconfig or multi_defconfig (or I failed to build the
toolchain properly))
Patch is against 3.19.0-rc7 (localversion-next is -next-20150204)
drivers/scsi/NCR5380.c | 10 +++++-----
drivers/scsi/atari_NCR5380.c | 2 +-
drivers/scsi/g_NCR5380.c | 6 +++---
3 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/drivers/scsi/NCR5380.c b/drivers/scsi/NCR5380.c
index 8981701..a777e5c 100644
--- a/drivers/scsi/NCR5380.c
+++ b/drivers/scsi/NCR5380.c
@@ -474,11 +474,11 @@ static void NCR5380_print_phase(struct Scsi_Host
*instance)
*/
#ifndef USLEEP_SLEEP
/* 20 ms (reasonable hard disk speed) */
-#define USLEEP_SLEEP (20*HZ/1000)
+#define USLEEP_SLEEP msecs_to_jiffies(20)
#endif
/* 300 RPM (floppy speed) */
#ifndef USLEEP_POLL
-#define USLEEP_POLL (200*HZ/1000)
+#define USLEEP_POLL msecs_to_jiffies(200)
#endif
#ifndef USLEEP_WAITLONG
/* RvC: (reasonable time to wait on select error) */
@@ -576,7 +576,7 @@ static int __init __maybe_unused NCR5380_probe_irq(struct
Scsi_Host *instance,
if ((mask & possible) && (request_irq(i, &probe_intr, 0,
"NCR-probe", NULL) == 0))
trying_irqs |= mask;
- timeout = jiffies + (250 * HZ / 1000);
+ timeout = jiffies + msecs_to_jiffies(250);
probe_irq = NO_IRQ;
/*
@@ -634,7 +634,7 @@ static void prepare_info(struct Scsi_Host *instance)
"sg_tablesize %d, this_id %d, "
"flags { %s%s%s}, "
#if defined(USLEEP_POLL) && defined(USLEEP_WAITLONG)
- "USLEEP_POLL %d, USLEEP_WAITLONG %d, "
+ "USLEEP_POLL %lu, USLEEP_WAITLONG %lu, "
#endif
"options { %s} ",
instance->hostt->name, instance->io_port, instance->n_io_port,
@@ -1346,7 +1346,7 @@ static int NCR5380_select(struct Scsi_Host *instance,
struct scsi_cmnd *cmd)
* selection.
*/
- timeout = jiffies + (250 * HZ / 1000);
+ timeout = jiffies + msecs_to_jiffies(250);
/*
* XXX very interesting - we're seeing a bounce where the BSY we
diff --git a/drivers/scsi/atari_NCR5380.c b/drivers/scsi/atari_NCR5380.c
index a702554..db87ece 100644
--- a/drivers/scsi/atari_NCR5380.c
+++ b/drivers/scsi/atari_NCR5380.c
@@ -1486,7 +1486,7 @@ static int NCR5380_select(struct Scsi_Host *instance,
struct scsi_cmnd *cmd)
* selection.
*/
- timeout = jiffies + (250 * HZ / 1000);
+ timeout = jiffies + msecs_to_jiffies(250);
/*
* XXX very interesting - we're seeing a bounce where the BSY we
diff --git a/drivers/scsi/g_NCR5380.c b/drivers/scsi/g_NCR5380.c
index f35792f..a11b152 100644
--- a/drivers/scsi/g_NCR5380.c
+++ b/drivers/scsi/g_NCR5380.c
@@ -57,9 +57,9 @@
*/
/* settings for DTC3181E card with only Mustek scanner attached */
-#define USLEEP_POLL 1
-#define USLEEP_SLEEP 20
-#define USLEEP_WAITLONG 500
+#define USLEEP_POLL msecs_to_jiffies(10)
+#define USLEEP_SLEEP msecs_to_jiffies(200)
+#define USLEEP_WAITLONG msecs_to_jiffies(5000)
#define AUTOPROBE_IRQ
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
