The check for 53C80 registers accessibility was commented out because it was broken (inverted). Fix and enable it.
Signed-off-by: Ondrej Zary <li...@rainbow-software.org> --- drivers/scsi/g_NCR5380.c | 37 ++++++------------------------------- 1 file changed, 6 insertions(+), 31 deletions(-) diff --git a/drivers/scsi/g_NCR5380.c b/drivers/scsi/g_NCR5380.c index 038dddf..a7479c6 100644 --- a/drivers/scsi/g_NCR5380.c +++ b/drivers/scsi/g_NCR5380.c @@ -603,14 +603,10 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, if (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ)) printk("53C400r: no 53C80 gated irq after transfer"); -#if 0 - /* - * DON'T DO THIS - THEY NEVER ARRIVE! - */ - printk("53C400r: Waiting for 53C80 registers\n"); - while (NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG) + /* wait for 53C80 registers to be available */ + while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) ; -#endif + if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) printk(KERN_ERR "53C400r: no end dma signal\n"); @@ -632,7 +628,6 @@ static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, struct NCR5380_hostdata *hostdata = shost_priv(instance); int blocks = len / 128; int start = 0; - int i; NCR5380_write(hostdata->c400_ctl_status, CSR_BASE); NCR5380_write(hostdata->c400_blk_cnt, blocks); @@ -681,36 +676,16 @@ static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, blocks--; } -#if 0 - printk("53C400w: waiting for registers to be available\n"); - THEY NEVER DO ! while (NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG); - printk("53C400w: Got em\n"); -#endif - - /* Let's wait for this instead - could be ugly */ - /* All documentation says to check for this. Maybe my hardware is too - * fast. Waiting for it seems to work fine! KLL - */ - while (!(i = NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ)) { + /* wait for 53C80 registers to be available */ + while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) { udelay(4); /* DTC436 chip hangs without this */ /* FIXME - no timeout */ } - /* - * I know. i is certainly != 0 here but the loop is new. See previous - * comment. - */ - if (i) { - if (!((i = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER)) - printk(KERN_ERR "53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i); - } else - printk(KERN_ERR "53C400w: no 53C80 gated irq after transfer (last block)\n"); - -#if 0 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) { printk(KERN_ERR "53C400w: no end dma signal\n"); } -#endif + while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT)) ; // TIMEOUT return 0; -- Ondrej Zary -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html