add ufs node document for Hisilicon.
Signed-off-by: Li Wei <liwei...@huawei.com>
---
Documentation/devicetree/bindings/ufs/ufs-hisi.txt | 41 ++++++++++++++++++++++
.../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 10 ++++--
2 files changed, 48 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/ufs/ufs-hisi.txt
diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
new file mode 100644
index 000000000000..a48c44817367
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
@@ -0,0 +1,41 @@
+* Hisilicon Universal Flash Storage (UFS) Host Controller
+
+UFS nodes are defined to describe on-chip UFS hardware macro.
+Each UFS Host Controller should have its own node.
+
+Required properties:
+- compatible : compatible list, contains one of the following -
+ "hisilicon,hi3660-ufs", "jedec,ufs-1.1"
for hisi ufs
+ host controller present on Hi36xx
chipset.
+- reg : should contain UFS register address space & UFS SYS CTRL
register address,
+- interrupt-parent : interrupt device
+- interrupts : interrupt number
+- clocks : List of phandle and clock specifier pairs
+- clock-names : List of clock input name strings sorted in the same
+ order as the clocks property.
"ref_clk", "phy_clk" is optional
+- freq-table-hz : Array of <min max> operating frequencies stored in the
same
+ order as the clocks property. If this property is not
+ defined or a value in the array is "0" then it is assumed
+ that the frequency is set by the parent clock or a
+ fixed rate clock source.
+- resets : describe reset node register
+- reset-names : reset node register, the "rst" corresponds to reset the
whole UFS IP.
+
+Example:
+
+ ufs: ufs@ff3b0000 {
+ compatible = "hisilicon,hi3660-ufs", "jedec,ufs-1.1";
+ /* 0: HCI standard */
+ /* 1: UFS SYS CTRL */
+ reg = <0x0 0xff3b0000 0x0 0x1000>,
+ <0x0 0xff3b1000 0x0 0x1000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
+ <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
+ clock-names = "ref_clk", "phy_clk";
+ freq-table-hz = <0 0>, <0 0>;
+ /* offset: 0x84; bit: 12 */
+ resets = <&crg_rst 0x84 12>;
+ reset-names = "rst";
+ };
diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
index c39dfef76a18..2df00524bd21 100644
--- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
@@ -41,6 +41,8 @@ Optional properties:
-lanes-per-direction : number of lanes available per direction - either 1 or
2.
Note that it is assume same number of lanes is used
both
directions at once. If not specified, default is 2
lanes per direction.
+- resets : reset node register
+- reset-names : describe reset node register, the "rst" corresponds to
reset the whole UFS IP.
Note: If above properties are not defined it can be assumed that the supply
regulators or clocks are always on.
@@ -61,9 +63,11 @@ Example:
vccq-max-microamp = 200000;
vccq2-max-microamp = 200000;
- clocks = <&core 0>, <&ref 0>, <&iface 0>;
- clock-names = "core_clk", "ref_clk", "iface_clk";
- freq-table-hz = <100000000 200000000>, <0 0>, <0 0>;
+ clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>;
+ clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk";
+ freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>;
+ resets = <&reset 0 1>;
+ reset-names = "rst";
phys = <&ufsphy1>;
phy-names = "ufsphy";
};
--
2.15.0
