Paco wrote: >Hi Frederic >Could you please send me a copy of your /etc/isapnp.conf? There may be >some info missing from there. > >The AWE64 has a hardware bug that causes it to not report all of the >necessary isapnp information. In particular, the wave table of the AWE64 >doesn't get initialized properly. >-Paco Here is my /etc/isapnp.conf If you do not get it correctly I can try to send it as an attachment. # $Id: pnpdump.c,v 1.17 1998/11/10 22:45:04 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR # # Trying port address 0203 # Board 1 has serial identifier b0 1f 81 7f 99 c7 00 8c 0e # (DEBUG) (READPORT 0x0203) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING # Card 1: (serial identifier b0 1f 81 7f 99 c7 00 8c 0e) # Vendor Id CTL00c7, Serial Number 528580505, checksum 0xB0. # Version 1.0, Vendor version 1.0 # ANSI string -->Creative AWE64 PnP<-- # Vendor defined tag: 73 02 45 02 # # Logical device id CTL0045 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL00c7/528580505 (LD 0 # ANSI string -->Audio<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # IRQ 7. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 7 (MODE +E))) # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode (DMA 0 (CHANNEL 1)) # Next DMA channel 5. # 16 bit DMA only # Logical device is not a bus master # DMA may not execute in count by byte mode # DMA may execute in count by word mode # DMA channel speed in compatible mode (DMA 1 (CHANNEL 5)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 1 bytes # Number of IO addresses required: 16 (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 1 bytes # Number of IO addresses required: 2 (IO 1 (SIZE 2) (BASE 0x0330)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # Number of IO addresses required: 4 (IO 2 (SIZE 4) (BASE 0x0388)) # End dependent functions (NAME "CTL00c7/528580505[0]{Audio }") (ACT Y))) # # Logical device id CTL0022 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL00c7/528580505 (LD 2 # ANSI string -->WaveTable<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0620 # Maximum IO base address 0x0620 # IO base alignment 1 bytes # Number of IO addresses required: 4 (IO 0 (SIZE 4) (BASE 0x0620)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0620 # Maximum IO base address 0x0680 # IO base alignment 32 bytes # Number of IO addresses required: 4 (IO 1 (SIZE 4) (BASE 0x0A20)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0620 # Maximum IO base address 0x0680 # IO base alignment 32 bytes # Number of IO addresses required: 4 (IO 2 (SIZE 4) (BASE 0x0E20)) # End dependent functions # Vendor defined tag: 75 01 03 46 ca 8a (NAME "CTL00c7/528580505[2]{WaveTable }") (ACT Y))) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY) Ciao Fred
