The X96 Mate is an Allwinner H616 based TV box, featuring: - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU - 2GiB/4GiB RAM (fully usable!) - 16/32/64GiB eMMC - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported) - Unsupported Allwinner WiFi chip - 2 x USB 2.0 host ports - HDMI port - IR receiver - 5V/2A DC power supply via barrel plug
For more information see: https://linux-sunxi.org/X96_Mate Add a basic devicetree for it, with SD card and eMMC working, as well as serial and the essential peripherals, like the AXP PMIC. This DT is somewhat minimal, and should work on many other similar TV boxes with the Allwinner H616 chip. Signed-off-by: Andre Przywara <andre.przyw...@arm.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h616-x96-mate.dts | 178 ++++++++++++++++++ 2 files changed, 179 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 62f8d43cf84d..14053c566601 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts new file mode 100644 index 000000000000..6334f4e20fd0 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts @@ -0,0 +1,178 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2021 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + model = "X96 Mate"; + compatible = "hechuang,x96-mate", "allwinner,sun50i-h616"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the DC input */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&ir { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_dcdce>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dcdce>; + vqmmc-supply = <®_bldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp305: pmic@745 { + compatible = "x-powers,axp305", "x-powers,axp805", + "x-powers,axp806"; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <0>; + reg = <0x745>; + + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-sys"; + }; + + /* Enabled by the Android BSP */ + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext"; + status = "disabled"; + }; + + /* Enabled by the Android BSP */ + reg_aldo3: aldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext2"; + status = "disabled"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8"; + }; + + /* Enabled by the Android BSP */ + reg_bldo2: bldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8-2"; + status = "disabled"; + }; + + bldo3 { + /* unused */ + }; + + bldo4 { + /* unused */ + }; + + cldo1 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc2v5"; + }; + + cldo2 { + /* unused */ + }; + + cldo3 { + /* unused */ + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <1360000>; + regulator-max-microvolt = <1360000>; + regulator-name = "vdd-dram"; + }; + + reg_dcdce: dcdce { + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-eth-mmc"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; -- 2.17.6 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20210802003952.19942-12-andre.przywara%40arm.com.
