From: Oliver Schinagl <oli...@schinagl.nl>
This patch adds support for the ahci sata controler found on Allwinner A10
and A20 SoCs.
Orignally written by Olliver Schinagl using the approach of having a platform
device which probe method creates a new child platform device which gets
driven by ahci_platform.c, as done by ahci_imx.c .
Given that almost all functionality already is shared through libahci /
ata-core, and that ahci_platform.c cannot cleanly handle somewhat more complex
platform specific ahci cases, such as the sunxi case, it was refactored into
a stand-alone platform driver by Hans de Goede.
Signed-off-by: Olliver Schinagl <oli...@schinagl.nl>
Signed-off-by: Hans de Goede <hdego...@redhat.com>
---
.../devicetree/bindings/ata/ahci-sunxi.txt | 24 ++
drivers/ata/Kconfig | 9 +
drivers/ata/Makefile | 1 +
drivers/ata/ahci_sunxi.c | 349 +++++++++++++++++++++
4 files changed, 383 insertions(+)
create mode 100644 Documentation/devicetree/bindings/ata/ahci-sunxi.txt
create mode 100644 drivers/ata/ahci_sunxi.c
diff --git a/Documentation/devicetree/bindings/ata/ahci-sunxi.txt
b/Documentation/devicetree/bindings/ata/ahci-sunxi.txt
new file mode 100644
index 0000000..0792fa5
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/ahci-sunxi.txt
@@ -0,0 +1,24 @@
+Allwinner SUNXI AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible : compatible list, contains "allwinner,sun4i-a10-ahci"
+- reg : <registers mapping>
+- interrupts : <interrupt mapping for AHCI IRQ>
+- clocks : clocks for ACHI
+- clock-names : clock names for AHCI
+
+Optional properties:
+- pwr-supply : regulator to control the power supply GPIO
+
+Example:
+ ahci@01c18000 {
+ compatible = "allwinner,sun4i-a10-ahci";
+ reg = <0x01c18000 0x1000>;
+ interrupts = <0 56 1>;
+ clocks = <&ahb_gates 25>, <&pll6 0>;
+ clock-names = "ahb_sata", "pll6_sata";
+ pwr-supply = <®_ahci_5v>;
+ };
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 4e73772..3c80bbe 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -106,6 +106,15 @@ config AHCI_IMX
If unsure, say N.
+config AHCI_SUNXI
+ tristate "Allwinner sunxi AHCI SATA support"
+ depends on ARCH_SUNXI
+ help
+ This option enables support for the Allwinner sunxi SoC's
+ onboard AHCI SATA.
+
+ If unsure, say N.
+
config SATA_FSL
tristate "Freescale 3.0Gbps SATA support"
depends on FSL_SOC
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 46518c6..956abc3 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
obj-$(CONFIG_AHCI_IMX) += ahci_imx.o
+obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o libahci.o
# SFF w/ custom DMA
obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
diff --git a/drivers/ata/ahci_sunxi.c b/drivers/ata/ahci_sunxi.c
new file mode 100644
index 0000000..22d3972
--- /dev/null
+++ b/drivers/ata/ahci_sunxi.c
@@ -0,0 +1,349 @@
+/*
+ * Allwinner sunxi AHCI SATA platform driver
+ * Copyright 2013 Olliver Schinagl <oli...@schinagl.nl>
+ * Copyright 2014 Hans de Goede <hdego...@redhat.com>
+ *
+ * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
+ * Based on code from Allwinner Technology Co., Ltd. <www.allwinnertech.com>,
+ * Daniel Wang <danielw...@allwinnertech.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include "ahci.h"
+
+#define AHCI_BISTAFR 0x00a0
+#define AHCI_BISTCR 0x00a4
+#define AHCI_BISTFCTR 0x00a8
+#define AHCI_BISTSR 0x00ac
+#define AHCI_BISTDECR 0x00b0
+#define AHCI_DIAGNR0 0x00b4
+#define AHCI_DIAGNR1 0x00b8
+#define AHCI_OOBR 0x00bc
+#define AHCI_PHYCS0R 0x00c0
+#define AHCI_PHYCS1R 0x00c4
+#define AHCI_PHYCS2R 0x00c8
+#define AHCI_TIMER1MS 0x00e0
+#define AHCI_GPARAM1R 0x00e8
+#define AHCI_GPARAM2R 0x00ec
+#define AHCI_PPARAMR 0x00f0
+#define AHCI_TESTR 0x00f4
+#define AHCI_VERSIONR 0x00f8
+#define AHCI_IDR 0x00fc
+#define AHCI_RWCR 0x00fc
+#define AHCI_P0DMACR 0x0170
+#define AHCI_P0PHYCR 0x0178
+#define AHCI_P0PHYSR 0x017c
+
+struct sunxi_ahci {
+ struct ahci_host_priv hpriv;
+ struct regulator *pwr;
+ struct clk *sata_clk;
+ struct clk *ahb_clk;
+};
+
+static void sunxi_clrbits(void __iomem *reg, u32 clr_val)
+{
+ u32 reg_val;
+
+ reg_val = readl(reg);
+ reg_val &= ~(clr_val);
+ writel(reg_val, reg);
+}
+
+static void sunxi_setbits(void __iomem *reg, u32 set_val)
+{
+ u32 reg_val;
+
+ reg_val = readl(reg);
+ reg_val |= set_val;
+ writel(reg_val, reg);
+}
+
+static void sunxi_clrsetbits(void __iomem *reg, u32 clr_val, u32 set_val)
+{
+ u32 reg_val;
+
+ reg_val = readl(reg);
+ reg_val &= ~(clr_val);
+ reg_val |= set_val;
+ writel(reg_val, reg);
+}
+
+static u32 sunxi_getbits(void __iomem *reg, u8 mask, u8 shift)
+{
+ return (readl(reg) >> shift) & mask;
+}
+
+static int sunxi_ahci_phy_init(struct device *dev, void __iomem *reg_base)
+{
+ u32 reg_val;
+ int timeout;
+
+ /* This magic is from the original code */
+ writel(0, reg_base + AHCI_RWCR);
+ mdelay(5);
+
+ sunxi_setbits(reg_base + AHCI_PHYCS1R, BIT(19));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS0R,
+ (0x7 << 24),
+ (0x5 << 24) | BIT(23) | BIT(18));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS1R,
+ (0x3 << 16) | (0x1f << 8) | (0x3 << 6),
+ (0x2 << 16) | (0x6 << 8) | (0x2 << 6));
+ sunxi_setbits(reg_base + AHCI_PHYCS1R, BIT(28) | BIT(15));
+ sunxi_clrbits(reg_base + AHCI_PHYCS1R, BIT(19));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS0R,
+ (0x7 << 20), (0x3 << 20));
+ sunxi_clrsetbits(reg_base + AHCI_PHYCS2R,
+ (0x1f << 5), (0x19 << 5));
+ mdelay(5);
+
+ sunxi_setbits(reg_base + AHCI_PHYCS0R, (0x1 << 19));
+
+ timeout = 0x100000;
+ do {
+ reg_val = sunxi_getbits(reg_base + AHCI_PHYCS0R, 0x7, 28);
+ } while (--timeout && (reg_val != 0x2));
+ if (!timeout) {
+ dev_err(dev, "PHY power up failed.\n");
+ return -EIO;
+ }
+
+ sunxi_setbits(reg_base + AHCI_PHYCS2R, (0x1 << 24));
+
+ timeout = 0x100000;
+ do {
+ reg_val = sunxi_getbits(reg_base + AHCI_PHYCS2R, 0x1, 24);
+ } while (--timeout && reg_val);
+ if (!timeout) {
+ dev_err(dev, "PHY calibration failed.\n");
+ return -EIO;
+ }
+ mdelay(15);
+
+ writel(0x7, reg_base + AHCI_RWCR);
+
+ return 0;
+}
+
+void sunxi_ahci_pre_start_engine(struct ata_port *ap)
+{
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+
+ /* Setup DMA before DMA start */
+ sunxi_clrsetbits(hpriv->mmio + AHCI_P0DMACR, 0x0000ff00, 0x00004400);
+}
+
+static int sunxi_ahci_enable_clks(struct sunxi_ahci *ahci)
+{
+ int ret;
+
+ ret = clk_prepare_enable(ahci->sata_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(ahci->ahb_clk);
+ if (ret)
+ clk_disable_unprepare(ahci->sata_clk);
+
+ return ret;
+}
+
+static void sunxi_ahci_disable_clks(struct sunxi_ahci *ahci)
+{
+ clk_disable_unprepare(ahci->ahb_clk);
+ clk_disable_unprepare(ahci->sata_clk);
+}
+
+static void sunxi_ahci_host_stop(struct ata_host *host)
+{
+ struct ahci_host_priv *hpriv = host->private_data;
+ struct sunxi_ahci *ahci = hpriv->plat_data;
+
+ if (!IS_ERR(ahci->pwr))
+ regulator_disable(ahci->pwr);
+
+ sunxi_ahci_disable_clks(ahci);
+}
+
+static struct ata_port_operations sunxi_ahci_platform_ops = {
+ .inherits = &ahci_ops,
+ .host_stop = sunxi_ahci_host_stop,
+};
+
+static const struct ata_port_info sunxiahci_port_info = {
+ AHCI_HFLAGS(AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI |
+ AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ),
+ .flags = AHCI_FLAG_COMMON | ATA_FLAG_NCQ,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sunxi_ahci_platform_ops,
+};
+
+static struct scsi_host_template sunxi_ahci_platform_sht = {
+ AHCI_SHT("sunxi_ahci"),
+};
+
+static int sunxi_ahci_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct ata_port_info *ppi[] = { &sunxiahci_port_info, NULL };
+ struct sunxi_ahci *ahci;
+ struct ata_host *host;
+ int ret;
+
+ ahci = devm_kzalloc(&pdev->dev, sizeof(*ahci), GFP_KERNEL);
+ if (!ahci)
+ return -ENOMEM;
+
+ ahci->pwr = devm_regulator_get_optional(dev, "pwr");
+ if (IS_ERR(ahci->pwr) && PTR_ERR(ahci->pwr) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ host = ata_host_alloc_pinfo(dev, ppi, 1);
+ if (!host)
+ return -ENOMEM;
+
+ host->private_data = &ahci->hpriv;
+ host->flags |= ATA_HOST_PARALLEL_SCAN;
+
+ ahci->hpriv.flags = (unsigned long)ppi[0]->private_data;
+ ahci->hpriv.plat_data = ahci;
+ ahci->hpriv.pre_start_engine = sunxi_ahci_pre_start_engine;
+ ahci->hpriv.mmio = devm_ioremap_resource(dev,
+ platform_get_resource(pdev, IORESOURCE_MEM, 0));
+ if (IS_ERR(ahci->hpriv.mmio))
+ return PTR_ERR(ahci->hpriv.mmio);
+
+ ahci->ahb_clk = devm_clk_get(&pdev->dev, "ahb_sata");
+ if (IS_ERR(ahci->ahb_clk))
+ return PTR_ERR(ahci->ahb_clk);
+
+ ahci->sata_clk = devm_clk_get(&pdev->dev, "pll6_sata");
+ if (IS_ERR(ahci->sata_clk))
+ return PTR_ERR(ahci->sata_clk);
+
+ ret = sunxi_ahci_enable_clks(ahci);
+ if (ret)
+ return ret;
+
+ if (!IS_ERR(ahci->pwr)) {
+ ret = regulator_enable(ahci->pwr);
+ if (ret) {
+ sunxi_ahci_disable_clks(ahci);
+ return ret;
+ }
+ }
+
+ ret = sunxi_ahci_phy_init(dev, ahci->hpriv.mmio);
+ if (ret) {
+ sunxi_ahci_host_stop(host);
+ return ret;
+ }
+
+ ahci_save_initial_config(dev, &ahci->hpriv, 0, 0);
+
+ ret = ahci_reset_controller(host);
+ if (ret) {
+ sunxi_ahci_host_stop(host);
+ return ret;
+ }
+
+ ahci_init_controller(host);
+ ahci_print_info(host, "sunxi");
+
+ ret = ata_host_activate(host, platform_get_irq(pdev, 0),
+ ahci_interrupt, 0, &sunxi_ahci_platform_sht);
+ if (ret)
+ sunxi_ahci_host_stop(host);
+
+ return ret;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int sunxi_ahci_susp(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
+ struct sunxi_ahci *ahci = hpriv->plat_data;
+ int ret;
+
+ /*
+ * AHCI spec rev1.1 section 8.3.3:
+ * Software must disable interrupts prior to requesting a
+ * transition of the HBA to D3 state.
+ */
+ sunxi_clrbits(hpriv->mmio + HOST_CTL, HOST_IRQ_EN);
+
+ ret = ata_host_suspend(host, PMSG_SUSPEND);
+ if (ret)
+ return ret;
+
+ sunxi_ahci_disable_clks(ahci);
+
+ return 0;
+}
+
+static int sunxi_ahci_resume(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
+ struct sunxi_ahci *ahci = hpriv->plat_data;
+ int ret;
+
+ ret = sunxi_ahci_enable_clks(ahci);
+ if (ret)
+ return ret;
+
+ if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
+ ret = ahci_reset_controller(host);
+ if (ret)
+ return ret;
+
+ ahci_init_controller(host);
+ }
+
+ ata_host_resume(host);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(sunxi_ahci_pmo, sunxi_ahci_susp, sunxi_ahci_resume);
+
+static const struct of_device_id sunxi_ahci_of_match[] = {
+ { .compatible = "allwinner,sun4i-a10-ahci" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, sunxi_ahci_of_match);
+
+static struct platform_driver sunxi_ahci_driver = {
+ .probe = sunxi_ahci_probe,
+ .remove = ata_platform_remove_one,
+ .driver = {
+ .name = "sunxi-ahci",
+ .owner = THIS_MODULE,
+ .of_match_table = sunxi_ahci_of_match,
+ .pm = &sunxi_ahci_pmo,
+ },
+};
+module_platform_driver(sunxi_ahci_driver);
+
+MODULE_DESCRIPTION("Allwinner sunxi AHCI SATA platform driver");
+MODULE_AUTHOR("Olliver Schinagl <oli...@schinagl.nl>");
+MODULE_LICENSE("GPL");
--
1.8.4.2
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/groups/opt_out.
