On Wed, May 06, 2015 at 11:31:32AM +0200, Jens Kuske wrote: > The Allwinner H3 is a home entertainment system oriented SoC with > four Cortex-A7 cores and a Mali-400MP2 GPU. > > Signed-off-by: Jens Kuske <jensku...@gmail.com> > --- > arch/arm/boot/dts/sun8i-h3.dtsi | 468 > ++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 468 insertions(+) > create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi > > diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi > new file mode 100644 > index 0000000..53aab95 > --- /dev/null > +++ b/arch/arm/boot/dts/sun8i-h3.dtsi > @@ -0,0 +1,468 @@ > +/* > + * Copyright (C) 2015 Jens Kuske <jensku...@gmail.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public > + * License along with this file; if not, write to the Free > + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, > + * MA 02110-1301 USA
Could you remove that last paragraph?
It generates a checkpatch warning.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "skeleton.dtsi"
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> + interrupt-parent = <&gic>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu@1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu@2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu@3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + };
> +
> + memory {
> + reg = <0x40000000 0x80000000>;
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + osc24M: osc24M_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "osc24M";
> + };
> +
> + osc32k: osc32k_clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "osc32k";
> + };
> +
> + pll1: clk@01c20000 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun8i-a23-pll1-clk";
> + reg = <0x01c20000 0x4>;
> + clocks = <&osc24M>;
> + clock-output-names = "pll1";
> + };
> +
> + pll6: clk@01c20028 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-pll6-clk";
> + reg = <0x01c20028 0x4>;
> + clocks = <&osc24M>;
> + clock-output-names = "pll6", "pll6x2", "pll6d2";
> + };
> +
> + pll8: clk@01c20044 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun8i-h3-pll8-clk";
> + reg = <0x01c20044 0x4>;
> + clocks = <&osc24M>;
> + clock-output-names = "pll8";
> + };
> +
> + cpu: cpu_clk@01c20050 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-cpu-clk";
> + reg = <0x01c20050 0x4>;
> + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
> + clock-output-names = "cpu";
> + };
> +
> + axi: axi_clk@01c20050 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-axi-clk";
> + reg = <0x01c20050 0x4>;
> + clocks = <&cpu>;
> + clock-output-names = "axi";
> + };
> +
> + ahb1: ahb1_clk@01c20054 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun6i-a31-ahb1-clk";
> + reg = <0x01c20054 0x4>;
> + clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
> + clock-output-names = "ahb1";
> + };
> +
> + ahb2: ahb2_clk@01c2005c {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun8i-h3-ahb2-clk";
> + reg = <0x01c2005c 0x4>;
> + clocks = <&ahb1>, <&pll6 2>;
> + clock-output-names = "ahb2";
> + };
> +
> + apb1: apb1_clk@01c20054 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-apb0-clk";
> + reg = <0x01c20054 0x4>;
> + clocks = <&ahb1>;
> + clock-output-names = "apb1";
> + };
> +
> + apb2: apb2_clk@01c20058 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun4i-a10-apb1-clk";
> + reg = <0x01c20058 0x4>;
> + clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
> + clock-output-names = "apb2";
> + };
> +
> + ahb1_gates: ahb1_gates_clk@01c20060 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-ahb1-gates-clk";
> + reg = <0x01c20060 0x14>;
> + clocks = <&ahb1>;
> + clock-output-names = "ahb1_ce", "ahb1_dma", "ahb1_mmc0",
> + "ahb1_mmc1", "ahb1_mmc2", "ahb1_nand",
> + "ahb1_sdram", "ahb1_ts", "ahb1_hstimer",
> + "ahb1_spi0", "ahb1_spi1", "ahb1_otg",
> + "ahb1_otg_ehci0", "ahb1_ehic1",
> + "ahb1_ehic2", "ahb1_ehic3",
> + "ahb1_otg_ohci0", "ahb1_ve",
> + "ahb1_lcd0", "ahb1_lcd1", "ahb1_deint",
> + "ahb1_csi", "ahb1_tve", "ahb1_hdmi",
> + "ahb1_de", "ahb1_gpu", "ahb1_msgbox",
> + "ahb1_spinlock", "ahb1_ephy",
> "ahb1_dbg";
> + };
> +
> + ahb2_gates: ahb2_gates_clk@01c20060 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-ahb2-gates-clk";
> + reg = <0x01c20060 0x4>;
> + clocks = <&ahb2>;
> + clock-output-names = "ahb2_gmac", "ahb2_ohic1",
> + "ahb2_ohic2", "ahb2_ohic3";
> + };
> +
> + apb1_gates: clk@01c20068 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-apb1-gates-clk";
> + reg = <0x01c20068 0x4>;
> + clocks = <&apb1>;
> + clock-output-names = "apb1_codec", "apb1_spdif",
> + "apb1_pio", "apb1_ths", "apb1_i2s0",
> + "apb1_i2s1", "apb1_i2s2";
> + };
> +
> + apb2_gates: clk@01c2006c {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-apb2-gates-clk";
> + reg = <0x01c2006c 0x4>;
> + clocks = <&apb2>;
> + clock-output-names = "apb2_i2c0", "apb2_i2c1",
> + "apb2_i2c2", "apb2_uart0",
> + "apb2_uart1", "apb2_uart2",
> + "apb2_uart3", "apb2_sim";
I'd prefer if the clocks on a new line were right-aligned (like you
did for the mmc clocks just below).
> + };
> +
> + mmc0_clk: clk@01c20088 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun4i-a10-mmc-clk";
> + reg = <0x01c20088 0x4>;
> + clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> + clock-output-names = "mmc0",
> + "mmc0_output",
> + "mmc0_sample";
> + };
> +
> + mmc1_clk: clk@01c2008c {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun4i-a10-mmc-clk";
> + reg = <0x01c2008c 0x4>;
> + clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> + clock-output-names = "mmc1",
> + "mmc1_output",
> + "mmc1_sample";
> + };
> +
> + mmc2_clk: clk@01c20090 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun4i-a10-mmc-clk";
> + reg = <0x01c20090 0x4>;
> + clocks = <&osc24M>, <&pll6 0>, <&pll8>;
> + clock-output-names = "mmc2",
> + "mmc2_output",
> + "mmc2_sample";
> + };
> + };
> +
> + soc@01c00000 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + dma: dma-controller@01c02000 {
> + compatible = "allwinner,sun8i-h3-dma";
> + reg = <0x01c02000 0x1000>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ahb1_gates 6>;
> + resets = <&ahb12_rst 6>;
> + #dma-cells = <1>;
> + };
> +
> + mmc0: mmc@01c0f000 {
> + compatible = "allwinner,sun5i-a13-mmc";
> + reg = <0x01c0f000 0x1000>;
> + clocks = <&ahb1_gates 8>,
> + <&mmc0_clk 0>,
> + <&mmc0_clk 1>,
> + <&mmc0_clk 2>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> + resets = <&ahb12_rst 8>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + mmc1: mmc@01c10000 {
> + compatible = "allwinner,sun5i-a13-mmc";
> + reg = <0x01c10000 0x1000>;
> + clocks = <&ahb1_gates 9>,
> + <&mmc1_clk 0>,
> + <&mmc1_clk 1>,
> + <&mmc1_clk 2>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> + resets = <&ahb12_rst 9>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + mmc2: mmc@01c11000 {
> + compatible = "allwinner,sun5i-a13-mmc";
> + reg = <0x01c11000 0x1000>;
> + clocks = <&ahb1_gates 10>,
> + <&mmc2_clk 0>,
> + <&mmc2_clk 1>,
> + <&mmc2_clk 2>;
> + clock-names = "ahb",
> + "mmc",
> + "output",
> + "sample";
> + resets = <&ahb12_rst 10>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + };
> +
> + pio: pinctrl@01c20800 {
> + compatible = "allwinner,sun8i-h3-pinctrl";
> + reg = <0x01c20800 0x400>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&apb1_gates 5>;
> + gpio-controller;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + #size-cells = <0>;
> + #gpio-cells = <3>;
> +
> + uart0_pins_a: uart0@0 {
> + allwinner,pins = "PA4", "PA5";
> + allwinner,function = "uart0";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + mmc0_pins_a: mmc0@0 {
> + allwinner,pins =
> "PF0","PF1","PF2","PF3","PF4","PF5";
Could you have spaces between the commas, and wrap the line at 80
chars?
> + allwinner,function = "mmc0";
> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> +
> + mmc0_cd_pin: mmc0_cd_pin@0 {
> + allwinner,pins = "PF6";
> + allwinner,function = "gpio_in";
> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> + };
> +
> + mmc1_pins_a: mmc1@0 {
> + allwinner,pins =
> "PG0","PG1","PG2","PG3","PG4","PG5";
> + allwinner,function = "mmc1";
> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> + };
> + };
> +
> + ahb12_rst: reset@01c202c0 {
> + #reset-cells = <1>;
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + reg = <0x01c202c0 0xc>;
> + };
This reset controller also resets the timers, it should be initialised
much earlier.
What about having an allwinner,sun8i-h3-bus-reset, and adding it to
the list of compatibles to initialise earlier in
drivers/reset/reset-sunxi.c?
Of course, it would cover the other reset controllers that you have
below.
> + apb1_rst: reset@01c202d0 {
> + #reset-cells = <1>;
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + reg = <0x01c202d0 0x4>;
> + };
> +
> + apb2_rst: reset@01c202d8 {
> + #reset-cells = <1>;
> + compatible = "allwinner,sun6i-a31-clock-reset";
> + reg = <0x01c202d8 0x4>;
> + };
> +
> + timer@01c20c00 {
> + compatible = "allwinner,sun4i-a10-timer";
> + reg = <0x01c20c00 0xa0>;
> + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&osc24M>;
> + };
> +
> + wdt0: watchdog@01c20ca0 {
> + compatible = "allwinner,sun6i-a31-wdt";
> + reg = <0x01c20ca0 0x20>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + uart0: serial@01c28000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28000 0x400>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 16>;
> + resets = <&apb2_rst 16>;
> + dmas = <&dma 6>, <&dma 6>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart1: serial@01c28400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28400 0x400>;
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 17>;
> + resets = <&apb2_rst 17>;
> + dmas = <&dma 7>, <&dma 7>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart2: serial@01c28800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28800 0x400>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 18>;
> + resets = <&apb2_rst 18>;
> + dmas = <&dma 8>, <&dma 8>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + uart3: serial@01c28c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28c00 0x400>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&apb2_gates 19>;
> + resets = <&apb2_rst 19>;
> + dmas = <&dma 9>, <&dma 9>;
> + dma-names = "rx", "tx";
> + status = "disabled";
> + };
> +
> + gic: interrupt-controller@01c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x1000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
> IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + rtc: rtc@01f00000 {
> + compatible = "allwinner,sun6i-a31-rtc";
> + reg = <0x01f00000 0x54>;
> + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +};
> --
> 2.3.7
>
Have you tested the architected timers?
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
signature.asc
Description: Digital signature
