Signed-off-by: Roy Spliet <r.spl...@ultimaker.com>
---
board/sunxi/Kconfig | 8 +++-----
drivers/mtd/Makefile | 1 +
include/configs/sunxi-common.h | 33 +++++++++++++++++++++++++--------
3 files changed, 29 insertions(+), 13 deletions(-)
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index cf58d73..37bbd0f 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -269,17 +269,15 @@ config MMC_SUNXI_SLOT_EXTRA
slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
support for this.
-config SPL_NAND_SUPPORT
- bool "SPL/NAND mode support"
+config NAND_SUNXI
+ bool "NAND support"
depends on SPL
default n
---help---
This enables support for booting from NAND internal
memory. U-Boot SPL doesn't detect where is it load from,
therefore this option is needed to properly load image from
- flash. Option also disables MMC functionality on U-Boot due to
- initialization errors encountered, when both controllers are
- enabled.
+ flash.
config USB0_VBUS_PIN
string "Vbus enable pin for usb0 (otg)"
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 5467a95..124b0f9 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -18,3 +18,4 @@ obj-$(CONFIG_FTSMC020) += ftsmc020.o
obj-$(CONFIG_FLASH_CFI_LEGACY) += jedec_flash.o
obj-$(CONFIG_MW_EEPROM) += mw_eeprom.o
obj-$(CONFIG_ST_SMI) += st_smi.o
+obj-$(CONFIG_MTD_UBI) += ubi/
diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index cce0441..ec28c40 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -113,7 +113,7 @@
#endif
/* 4MB of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20))
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (64 << 20))
/*
* Miscellaneous configurable options
@@ -326,10 +326,31 @@ extern int soft_i2c_gpio_scl;
#define CONFIG_ENV_IS_NOWHERE
#endif
-#ifdef CONFIG_SPL_NAND_SUPPORT
+#ifdef CONFIG_NAND_SUNXI
+#ifndef CONFIG_NAND_SUNXI_GPC_PORTS
+#error "No NAND GPC ports defined, NAND unsupported"
+#endif /* CONFIG_NAND_SUNXI_GPC_PORTS */
#define CONFIG_NAND
#define CONFIG_SYS_NAND_SELF_INIT
-#define CONFIG_NAND_SUNXI
+#define CONFIG_SYS_MAX_NAND_DEVICE 8
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* Requirements for UBI */
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_MTD_DEVICE
+
+#define CONFIG_SPL_NAND_SUPPORT
+
+#define CONFIG_MTD_PARTITIONS
+/*
+#define CONFIG_MTD_DEBUG
+#define CONFIG_MTD_DEBUG_VERBOSE MTD_DEBUG_LEVEL3
+*/
#define CONFIG_CMD_SPL_WRITE_SIZE 0x000400
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x008000
@@ -338,11 +359,7 @@ extern int soft_i2c_gpio_scl;
#define CONFIG_NAND_SUNXI_ECC_STEP 1024
#define CONFIG_NAND_SUNXI_ECC_STRENGTH 40
#define CONFIG_NAND_SUNXI_ADDR_CYCLES 5
-
-#ifndef CONFIG_NAND_SUNXI_GPC_PORTS
-#error "No NAND GPC ports defined, NAND unsupported"
-#endif
-#endif /* CONFIG_SPL_NAND_SUPPORT */
+#endif /* CONFIG_NAND_SUNXI */
#define CONFIG_MISC_INIT_R
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
--
2.4.2
--
IMAGINE IT >> MAKE IT
Meet us online at Twitter <http://twitter.com/ultimaker>, Facebook
<http://facebook.com/ultimaker>, Google+ <http://google.com/+Ultimaker>
www.ultimaker.com
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
