Hi, On Sun, Jan 21, 2018 at 07:06:49PM +0100, codekip...@gmail.com wrote: > From: Marcus Cooper <codekip...@gmail.com> > > The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot, > 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using > the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, a dual > colour LED, an IR receiver and an optical S/PDIF connector. > > Signed-off-by: Marcus Cooper <codekip...@gmail.com> > --- > arch/arm/dts/Makefile | 1 + > arch/arm/dts/sun8i-h3-beelink-x2.dts | 155 > +++++++++++++++++++++++++++++++++++ > board/sunxi/MAINTAINERS | 5 ++ > configs/beelink_x2_defconfig | 18 ++++ > 4 files changed, 179 insertions(+) > create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts > create mode 100644 configs/beelink_x2_defconfig > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 9540ba4313..f899cef7ac 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -335,6 +335,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \ > dtb-$(CONFIG_MACH_SUN8I_H3) += \ > sun8i-h2-plus-orangepi-zero.dtb \ > sun8i-h3-bananapi-m2-plus.dtb \ > + sun8i-h3-beelink-x2.dtb \ > sun8i-h3-libretech-all-h3-cc.dtb \ > sun8i-h3-orangepi-2.dtb \ > sun8i-h3-orangepi-lite.dtb \ > diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts > b/arch/arm/dts/sun8i-h3-beelink-x2.dts > new file mode 100644 > index 0000000000..43f67eb8db > --- /dev/null > +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts > @@ -0,0 +1,155 @@ > +/* > + * Copyright (C) 2017 Marcus Cooper <codekip...@gmail.com> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "sun8i-h3.dtsi" > +#include "sunxi-common-regulators.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "Beelink X2"; > + compatible = "roofull,beelink-x2", "allwinner,sun8i-h3"; > + > + aliases { > + serial0 = &uart0; > + /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */ > + ethernet1 = &sdiowifi; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + blue { > + label = "beelink-x2:blue:pwr"; > + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ > + default-state = "on"; > + }; > + > + red { > + label = "beelink-x2:red:standby"; > + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ > + }; > + }; > + > + wifi_pwrseq: wifi_pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ > + }; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +&emac { > + phy = <&phy1>; > + phy-mode = "mii"; > + allwinner,use-internal-phy; > + allwinner,leds-active-low; > + status = "okay"; > + phy1: ethernet-phy@1 { > + reg = <1>; > + }; > +}; > + > +&ir { > + pinctrl-names = "default"; > + pinctrl-0 = <&ir_pins_a>; > + status = "okay"; > +}; > + > +&mmc0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <4>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ > + cd-inverted; > + status = "okay"; > +}; > + > +&mmc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc1_pins_a>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <4>; > + non-removable; > + status = "okay"; > + > + /* > + * Explicitly define the sdio device, so that we can add an ethernet > + * alias for it (which e.g. makes u-boot set a mac-address). > + */ > + sdiowifi: sdio_wifi@1 { > + reg = <1>; > + }; > +}; > + > +&mmc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_8bit_pins>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + status = "okay"; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins_a>; > + status = "okay"; > +}; > + > +&usbphy { > + status = "okay"; > +};
Where is that DT coming from? The one in Linux looks different. Looks good otherwise! Thanks! Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
signature.asc
Description: PGP signature