On boards where the only peripheral connected to PL0/PL1 is an X-Powers PMIC, configure the connection to use the RSB bus rather than the I2C bus. Compared to the I2C controller that shares the pins, the RSB controller allows a higher bus frequency, and it is more CPU-efficient.
Signed-off-by: Samuel Holland <sam...@sholland.org> --- .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 38 +++++++++---------- .../dts/allwinner/sun50i-h6-orangepi-3.dts | 14 +++---- .../dts/allwinner/sun50i-h6-orangepi.dtsi | 22 +++++------ 3 files changed, 37 insertions(+), 37 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts index 7c9dbde645b5..3452add30cc4 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts @@ -150,12 +150,28 @@ &pio { vcc-pg-supply = <®_aldo1>; }; -&r_i2c { +&r_ir { + linux,rc-map-name = "rc-beelink-gs1"; + status = "okay"; +}; + +&r_pio { + /* + * FIXME: We can't add that supply for now since it would + * create a circular dependency between pinctrl, the regulator + * and the RSB Bus. + * + * vcc-pl-supply = <®_aldo1>; + */ + vcc-pm-supply = <®_aldo1>; +}; + +&r_rsb { status = "okay"; - axp805: pmic@36 { + axp805: pmic@745 { compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; + reg = <0x745>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; @@ -273,22 +289,6 @@ sw { }; }; -&r_ir { - linux,rc-map-name = "rc-beelink-gs1"; - status = "okay"; -}; - -&r_pio { - /* - * PL0 and PL1 are used for PMIC I2C - * don't enable the pl-supply else - * it will fail at boot - * - * vcc-pl-supply = <®_aldo1>; - */ - vcc-pm-supply = <®_aldo1>; -}; - &rtc { clocks = <&ext_osc32k>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 15c9dd8c4479..16702293ac0b 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -175,12 +175,16 @@ &pio { vcc-pg-supply = <®_vcc_wifi_io>; }; -&r_i2c { +&r_ir { + status = "okay"; +}; + +&r_rsb { status = "okay"; - axp805: pmic@36 { + axp805: pmic@745 { compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; + reg = <0x745>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; @@ -291,10 +295,6 @@ sw { }; }; -&r_ir { - status = "okay"; -}; - &rtc { clocks = <&ext_osc32k>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi index ebc120a9232f..23e3cb2ffd8d 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi @@ -112,12 +112,20 @@ &pio { vcc-pg-supply = <®_aldo1>; }; -&r_i2c { +&r_ir { + status = "okay"; +}; + +&r_pio { + vcc-pm-supply = <®_bldo3>; +}; + +&r_rsb { status = "okay"; - axp805: pmic@36 { + axp805: pmic@745 { compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; + reg = <0x745>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; @@ -232,14 +240,6 @@ sw { }; }; -&r_ir { - status = "okay"; -}; - -&r_pio { - vcc-pm-supply = <®_bldo3>; -}; - &rtc { clocks = <&ext_osc32k>; }; -- 2.26.2 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscr...@googlegroups.com. To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20210103100007.32867-5-samuel%40sholland.org.