The Omnivision OV5640 is supported by Linux thanks to its device tree
binding.
Now that we have the DT validation in place, let's convert the device
tree bindings for that driver over to a YAML schema.
Cc: linux-me...@vger.kernel.org
Cc: Mauro Carvalho Chehab <mche...@kernel.org>
Cc: Steve Longerbeam <slongerb...@gmail.com>
Signed-off-by: Maxime Ripard <max...@cerno.tech>
---
.../devicetree/bindings/media/i2c/ov5640.txt | 92 -----------
.../bindings/media/i2c/ovti,ov5640.yaml | 154 ++++++++++++++++++
2 files changed, 154 insertions(+), 92 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
deleted file mode 100644
index c97c2f2da12d..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
+++ /dev/null
@@ -1,92 +0,0 @@
-* Omnivision OV5640 MIPI CSI-2 / parallel sensor
-
-Required Properties:
-- compatible: should be "ovti,ov5640"
-- clocks: reference to the xclk input clock.
-- clock-names: should be "xclk".
-- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
-- AVDD-supply: Analog voltage supply, 2.8 volts
-- DVDD-supply: Digital core voltage supply, 1.5 volts
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the reset pin, if any.
- This is an active low signal to the OV5640.
-- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
- if any. This is an active high signal to the OV5640.
-- rotation: as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt,
- valid values are 0 (sensor mounted upright) and 180 (sensor
- mounted upside down).
-
-The device node must contain one 'port' child node for its digital output
-video port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
-- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
-
-Endpoint node required properties for parallel connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- bus-width: shall be set to <8> for 8 bits parallel bus
- or <10> for 10 bits parallel bus
-- data-shift: shall be set to <2> for 8 bits parallel bus
- (lines 9:2 are used) or <0> for 10 bits parallel bus
-- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH
respectively.
-- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH
respectively.
-- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
- signal.
-
-Examples:
-
-&i2c1 {
- ov5640: camera@3c {
- compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ov5640>;
- reg = <0x3c>;
- clocks = <&clks IMX6QDL_CLK_CKO>;
- clock-names = "xclk";
- DOVDD-supply = <&vgen4_reg>; /* 1.8v */
- AVDD-supply = <&vgen3_reg>; /* 2.8v */
- DVDD-supply = <&vgen2_reg>; /* 1.5v */
- powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
- rotation = <180>;
-
- port {
- /* MIPI CSI-2 bus endpoint */
- ov5640_to_mipi_csi2: endpoint {
- remote-endpoint = <&mipi_csi2_from_ov5640>;
- clock-lanes = <0>;
- data-lanes = <1 2>;
- };
- };
- };
-};
-
-&i2c1 {
- ov5640: camera@3c {
- compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ov5640>;
- reg = <0x3c>;
- clocks = <&clk_ext_camera>;
- clock-names = "xclk";
-
- port {
- /* Parallel bus endpoint */
- ov5640_to_parallel: endpoint {
- remote-endpoint = <¶llel_from_ov5640>;
- bus-width = <8>;
- data-shift = <2>; /* lines 9:2 are used */
- hsync-active = <0>;
- vsync-active = <0>;
- pclk-sample = <1>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
new file mode 100644
index 000000000000..0283b1895a75
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
@@ -0,0 +1,154 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV5640 Image Sensor Device Tree Bindings
+
+maintainers:
+ - Steve Longerbeam <slongerb...@gmail.com>
+
+allOf:
+ - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+ compatible:
+ const: ovti,ov5640
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ description: XCLK Input Clock
+
+ clock-names:
+ const: xclk
+
+ AVDD-supply:
+ description: Analog voltage supply, 2.8 volts
+
+ DVDD-supply:
+ description: Digital core voltage supply, 1.5 volts
+
+ DOVDD-supply:
+ description: Digital I/O voltage supply, 1.8 volts
+
+ powerdown-gpios:
+ maxItems: 1
+ description: >
+ Reference to the GPIO connected to the powerdown pin, if any.
+
+ reset-gpios:
+ maxItems: 1
+ description: >
+ Reference to the GPIO connected to the reset pin, if any.
+
+ rotation:
+ enum:
+ - 0
+ - 180
+
+ port:
+ description: Digital Output Port
+ $ref: /schemas/graph.yaml#/properties/port
+ additionalProperties: false
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ clock-lanes:
+ const: 0
+
+ data-lanes:
+ minItems: 1
+ maxItems: 2
+ items:
+ enum: [1, 2]
+
+ bus-width:
+ enum: [8, 10]
+
+ data-shift:
+ enum: [0, 2]
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - AVDD-supply
+ - DVDD-supply
+ - DOVDD-supply
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx6qdl-clock.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@3c {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v */
+ powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ rotation = <180>;
+
+ port {
+ /* MIPI CSI-2 bus endpoint */
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_from_ov5640>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@3c {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clk_ext_camera>;
+ clock-names = "xclk";
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v */
+
+ port {
+ /* Parallel bus endpoint */
+ ov5640_to_parallel: endpoint {
+ remote-endpoint = <¶llel_from_ov5640>;
+ bus-width = <8>;
+ data-shift = <2>; /* lines 9:2 are used */
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ };
+ };
+ };
+ };
+
+...
--
2.31.1
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to linux-sunxi+unsubscr...@googlegroups.com.
To view this discussion on the web, visit
https://groups.google.com/d/msgid/linux-sunxi/20210721140424.725744-23-maxime%40cerno.tech.
