I have a Lexmark E210 USB printer, which prints fine unless it is
powered off, or the cable is disconnected. When the printer comes back
up I get an error message "usb.c: USB device not accepting new address=3
(error=-110)". You aren't able to print again unless you remove then
insert the modules "uhci" and "printer". Then everything is fine again.
Any suggestions? Logs are below.
I'm running debian/woody with a 2.4.18 kernel. The motherboard is an
Aopen 440BX.
The USB device from proc/ide
Bus 0, device 7, function 2:
USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 1).
IRQ 10.
Master Capable. Latency=32.
I/O at 0x6400 [0x641f].
Jun 13 15:11:48 clear kernel: usb.c: USB disconnect on device 2
Jun 13 15:11:48 clear kernel: printer.c: usblp0: removed
Jun 13 15:11:50 clear kernel: hub.c: USB new device connect on bus1/1,
assigned device number 3
Jun 13 15:11:50 clear kernel: usb-uhci.c: interrupt, status 2, frame# 1385
Jun 13 15:11:50 clear kernel: usb.c: USB device not accepting new
address=3 (error=-110)
Jun 13 15:11:51 clear kernel: hub.c: USB new device connect on bus1/1,
assigned device number 4
Jun 13 15:11:51 clear kernel: usb.c: USB device not accepting new
address=4 (error=-110)
Jun 13 15:12:24 clear kernel: usb.c: USB disconnect on device 1
Jun 13 15:12:24 clear kernel: usb.c: USB bus 1 deregistered
Jun 13 15:12:24 clear kernel: usb.c: deregistering driver usblp
Jun 13 15:12:24 clear kernel: usb.c: deregistering driver usbdevfs
Jun 13 15:12:24 clear kernel: usb.c: deregistering driver hub
Jun 13 15:12:31 clear kernel: usb.c: registered new driver usbdevfs
Jun 13 15:12:31 clear kernel: usb.c: registered new driver hub
Jun 13 15:12:31 clear kernel: usb-uhci.c: $Revision: 1.275 $ time
00:21:06 Mar 1 2002
Jun 13 15:12:31 clear kernel: usb-uhci.c: High bandwidth mode enabled
Jun 13 15:12:31 clear kernel: PCI: Found IRQ 10 for device 00:07.2
Jun 13 15:12:31 clear kernel: usb-uhci.c: USB UHCI at I/O 0x6400, IRQ 10
Jun 13 15:12:31 clear kernel: usb-uhci.c: Detected 2 ports
Jun 13 15:12:31 clear kernel: usb.c: new USB bus registered, assigned
bus number 1
Jun 13 15:12:31 clear kernel: hub.c: USB hub found
Jun 13 15:12:31 clear kernel: hub.c: 2 ports detected
Jun 13 15:12:31 clear kernel: usb-uhci.c: v1.275:USB Universal Host
Controller Interface driver
Jun 13 15:12:31 clear kernel: usb.c: registered new driver usblp
Jun 13 15:12:31 clear kernel: printer.c: v0.8:USB Printer Device Class
driver
Jun 13 15:12:31 clear kernel: hub.c: USB new device connect on bus1/1,
assigned device number 2
Jun 13 15:12:31 clear kernel: usb.c: ignoring set_interface for dev 2,
iface 0, alt 0
_______________________________________________________________
Don't miss the 2002 Sprint PCS Application Developer's Conference
August 25-28 in Las Vegas -
http://devcon.sprintpcs.com/adp/index.cfm?source=osdntextlink
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
