I upgraded my SA-1110/SA-1111 platform from 2.5.59-rmk1 to 2.5.65-rmk1. I'm seeng regression with OHCI under 2.5.65: my device, a Blue Gear B091H1 Bluetooth dongle, fails to accept its address under 2.5.65. If I reboot under 2.5.59, it works OK although I do get an initial "USB device not accepting new address".
Logs follow for both the working 2.5.59 and the not working 2.5.65. Any thoughts before I dig into this further? Ciao, -ch ------------------------------------- **** 2.5.65 -- does not work **** Linux version 2.5.65-rmk1-ch1 ([EMAIL PROTECTED]) (gcc version 2.95.4 20010319 (prerelease)) #4 Wed Mar 19 12:15:33 PST 2003 CPU: StrongARM-1110 [6901b110] revision 0 (ARMv4) Machine: Hewlett-Packard Laboratories BadgePAD 4 .... drivers/usb/host/ohci-sa1111.c: ohci-hcd (SA-1111) at 0xcc800400, irq 109 Please use the 'usbfs' filetype instead, the 'usbdevfs' name is deprecated. sa1111-ohci 0400: new USB bus registered, assigned bus number 1 usb usb1: Product: SA-1111 OHCI usb usb1: Manufacturer: Linux 2.5.65-rmk1-ch1 ohci-hcd usb usb1: SerialNumber: sa1111 hub 1-0:0: USB hub found hub 1-0:0: 1 port detected hub 1-0:0: debounce: port 1: delay 100ms stable 4 status 0x101 hub 1-0:0: new USB device on port 1, assigned address 2 usb 1-1: USB device not accepting new address=2 (error=-32) hub 1-0:0: new USB device on port 1, assigned address 3 usb 1-1: USB device not accepting new address=3 (error=-32) ------------------------------------- **** 2.5.59 -- does not work **** Linux version 2.5.59-rmk1-ch1 ([EMAIL PROTECTED]) (gcc version 2.95.4 20010319 (prerelease)) #1 Thu Mar 6 18:53:43 PST 2003 CPU: StrongARM-1110 [6901b110] revision 0 (ARMv4) Machine: Hewlett-Packard Laboratories BadgePAD 4 ... drivers/usb/host/ohci-sa1111.c: 2002-Sep-17 USB 1.1 'Open' Host Controller (OHCI) Driver (SA-1111) drivers/usb/host/ohci-sa1111.c: block sizes: ed 64 td 64 drivers/usb/host/ohci-sa1111.c: starting SA-1111 OHCI USB Controller drivers/usb/host/ohci-sa1111.c: ohci-hcd (SA-1111) at 0xcc800400, irq 109 Please use the 'usbfs' filetype instead, the 'usbdevfs' name is deprecated. sa1111-ohci 0400: new USB bus registered, assigned bus number 1 sa1111-ohci 0400: USB HC reset_hc sa1111: ctrl = 0x0 ; sa1111-ohci 0400: root hub device address 1 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/usb.c: usb_hotplug usb usb1: usb_new_device - registering interface 1-0:0 hub 1-0:0: usb_device_probe hub 1-0:0: usb_device_probe - got id hub 1-0:0: USB hub found hub 1-0:0: 1 port detected hub 1-0:0: standalone hub hub 1-0:0: ganged power switching hub 1-0:0: global over-current protection hub 1-0:0: Port indicators are not supported hub 1-0:0: power on to power good time: 4ms hub 1-0:0: hub controller current requirement: 0mA hub 1-0:0: local power source is good hub 1-0:0: no over-current condition exists hub 1-0:0: enabling power on all ports drivers/usb/core/usb.c: usb_hotplug sa1111-ohci 0400: created debug files sa1111-ohci 0400: OHCI controller state sa1111-ohci 0400: OHCI 1.0, with legacy support registers sa1111-ohci 0400: control: 0x0000008f HCFS=operational IE PLE CBSR=3 sa1111-ohci 0400: cmdstatus: 0x00000000 SOC=0 sa1111-ohci 0400: intrstatus: 0x00000044 RHSC SF sa1111-ohci 0400: intrenable: 0x80000012 MIE UE WDH sa1111-ohci 0400: hcca frame #0020 sa1111-ohci 0400: roothub.a: 02000201 POTPGT=2 NPS NDP=1 sa1111-ohci 0400: roothub.b: 00000000 PPCM=0000 DR=0000 sa1111-ohci 0400: roothub.status: 00000000 sa1111-ohci 0400: roothub.portstatus [0] = 0x00000100 PPS sa1111-ohci 0400: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS hub 1-0:0: port 1, status 101, change 1, 12 Mb/s hub 1-0:0: debounce: port 1: delay 100ms stable 4 status 0x101 sa1111-ohci 0400: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS hub 1-0:0: new USB device on port 1, assigned address 2 usb 1-1: urb c3f97d20 usb-sa1111-1 ep-0-OUT cc 5 --> status -110 usb 1-1: urb c3f97c00 usb-sa1111-1 ep-0-OUT cc 5 --> status -110 usb 1-1: USB device not accepting new address=2 (error=-110) sa1111-ohci 0400: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS hub 1-0:0: new USB device on port 1, assigned address 3 usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0 drivers/usb/core/usb.c: usb_hotplug usb 1-1: usb_new_device - registering interface 1-1:0 drivers/usb/core/usb.c: usb_hotplug usb 1-1: usb_new_device - registering interface 1-1:1 drivers/usb/core/usb.c: usb_hotplug usb 1-1: usb_new_device - registering interface 1-1:2 drivers/usb/core/usb.c: usb_hotplug ------------------------------------------------------- This SF.net email is sponsored by: Does your code think in ink? You could win a Tablet PC. Get a free Tablet PC hat just for playing. What are you waiting for? http://ads.sourceforge.net/cgi-bin/redirect.pl?micr5043en _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
