[1.] Problems with ServerWorks OSB4/CSB5 OHCI USB Controller of Dell
PowerEdge 1600SC
[2.] Full description of the problem/report:

Having installed and configured an USRobotics 8500 and a ZyXEL 640-31
ADSL USB Modems with eciadsl-0.9-1 [1] on a Dell PowerEdge 1600SC
running Debian with several custom kernels, in all of them, the modems
were _very_ unstable, the connection was stablished, but after some
minutes the connection got very slow and then it got lost.

[1] http://eciadsl.flashtux.org/

We have tried both kernel.org and debian's kernel-source-*s. 

On Kernel 2.4.26, we got these messages since the modem was connected
to the server:

Sep  4 17:12:27 coconuco kernel: usb: raced timeout, pipe 0xc0010400
status 0 time left 0
Sep  4 17:15:10 coconuco kernel: usb: raced timeout, pipe 0xc0010400
status 0 time left 0
Sep  4 17:15:11 coconuco kernel: usb: raced timeout, pipe 0xc0010400
status 0 time left 0
Sep  4 17:17:21 coconuco kernel: usb: raced timeout, pipe 0xc0010400
status 0 time left 0
Sep  4 17:20:36 coconuco kernel: usb: raced timeout, pipe 0x80000400
status 0 time left 0
Sep  4 17:20:43 coconuco kernel: usb: raced timeout, pipe 0xc0010400
status 0 time left 0
Sep  4 17:22:48 coconuco kernel: usb: raced timeout, pipe 0xc0010400
status 0 time left 0

So, We asked for a solution in the eciadsl maillist[2] and we were
told that the problem was very common on 2.4 kernels, so we upgraded
to 2.6.

[2] http://liste.eci.free.fr/voir.php3?dt=20040909

On kernel 2.6.8:

Sep  6 12:44:31 coconuco kernel: usb-ohci.c: USB OHCI at membase
0xe08b8000, IRQ 3
Sep  6 12:44:31 coconuco kernel: usb-ohci.c: usb-00:0f.2, ServerWorks
OSB4/CSB5 OHCI USB Controller
Sep  6 12:44:31 coconuco kernel: usb.c: new USB bus registered,
assigned bus number 1
Sep  6 12:44:31 coconuco kernel: hub.c: USB hub found
Sep  6 12:44:31 coconuco kernel: hub.c: new USB device 00:0f.2-2,
assigned address 2
Sep  6 12:44:31 coconuco kernel: usb.c: USB device 2 (vend/prod
0x915/0xe7) is not claimed by any active driver.
Sep  6 12:44:31 coconuco kernel: usbdevfs: USBDEVFS_BULK failed dev 2
ep 0x2 len 64 ret -110
Sep  6 12:44:31 coconuco kernel: usbdevfs: USBDEVFS_BULK failed dev 2
ep 0x2 len 64 ret -110
Sep  6 12:44:31 coconuco kernel: usbdevfs: USBDEVFS_BULK failed dev 2
ep 0x2 len 64 ret -110
Sep  6 12:44:31 coconuco kernel: usbdevfs: USBDEVFS_BULK failed dev 2
ep 0x2 len 64 ret -110
Sep  6 12:44:31 coconuco kernel: usbdevfs: USBDEVFS_BULK failed dev 2
ep 0x2 len 64 ret -110

By recommendation of the eciadsl developers, we tried kernel 2.6.6
with a usb patch [3] instead of 2.6.8, but the problem persisted, but,
with a different message:

[3] http://eciadsl.flashtux.org/download/beta/2.6.x-usb.patch

Sep 10 09:56:01 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 768 ret -110
Sep 10 09:56:02 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 768 ret -110
Sep 10 09:56:02 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 768 ret -110
Sep 10 09:56:02 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 768 ret -110
Sep 10 09:56:04 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 64 ret -110
Sep 10 09:58:04 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 128 ret -110
Sep 10 09:58:04 coconuco kernel: usb 1-1: usbfs: USBDEVFS_BULK failed
ep 0x2 len 128 ret -110

Also, we have searched for an USB chipset software upgrade and even we
called Dell's support without success.

In a desperation act, we bought a usb-pci VIA card as a last resource,
and now, it works very well.

[3.] Keywords: usb, ohci, uhci, modem.
[4.] Kernel version (from /proc/version):
coconuco:/var/log# cat /proc/version
Linux version 2.6.6 ([EMAIL PROTECTED]) (gcc version 3.3.4 (Debian
1:3.3.4-3)) #1 SMP Tue Sep 14 11:30:25 COT 2004

[5.] Output of Oops.. message (if applicable) with symbolic information
     resolved (see Documentation/oops-tracing.txt)
[6.] A small shell script or example program which triggers the
     problem (if possible)
[7.] Environment
Dell PowerEdge 1600SC running Debian GNU/Linux with custom kernel 2.6.6

[7.1.] Software (add the output of the ver_linux script here)
coconuco:/usr/src/linux# scripts/ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
  
Linux coconuco 2.6.6 #1 SMP Tue Sep 14 11:30:25 COT 2004 i686 unknown
  
Gnu C                  3.3.4
Gnu make               3.79.1
binutils               2.14.90.0.7
util-linux             2.11n
mount                  2.11n
module-init-tools      3.1-pre5
e2fsprogs              1.27
quota-tools            3.12.
PPP                    2.4.1
nfs-utils              1.0
Linux C Library        2.3.2
Dynamic linker (ldd)   2.3.2
Procps                 2.0.7
Net-tools              1.60
Console-tools          0.2.3
Sh-utils               2.0.11
Modules Loaded         n_hdlc uhci_hcd ppp_synctty bsd_comp
ppp_generic slhc ohci_hcd zlib_inflate zlib_deflate usbhid usbcore
e1000

[7.2.] Processor information (from /proc/cpuinfo):

coconuco:/usr/src/linux# cat /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 15
model           : 2
model name      : Intel(R) Xeon(TM) CPU 2.40GHz
stepping        : 9
cpu MHz         : 2392.350
cache size      : 512 KB
physical id     : 0
siblings        : 2
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid
bogomips        : 4718.59
 
processor       : 1
vendor_id       : GenuineIntel
cpu family      : 15
model           : 2
model name      : Intel(R) Xeon(TM) CPU 2.40GHz
stepping        : 9
cpu MHz         : 2392.350
cache size      : 512 KB
physical id     : 0
siblings        : 2
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 2
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid
bogomips        : 4784.12
 


[7.3.] Module information (from /proc/modules):

coconuco:/usr/src/linux# cat /proc/modules
n_hdlc 14084 1 - Live 0xe0895000
uhci_hcd 34832 0 - Live 0xe0935000
ppp_synctty 13440 1 - Live 0xe0925000
bsd_comp 10240 0 - Live 0xe0921000
ppp_generic 29588 6 ppp_synctty,bsd_comp, Live 0xe08fc000
slhc 11648 1 ppp_generic, Live 0xe089a000
ohci_hcd 23172 0 - Live 0xe08f5000
zlib_inflate 26112 0 - Live 0xe08ed000
zlib_deflate 25880 0 - Live 0xe08e5000
usbhid 36160 0 - Live 0xe089f000
usbcore 109020 5 uhci_hcd,ohci_hcd,usbhid, Live 0xe0905000
e1000 85764 0 - Live 0xe08ac000


[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
coconuco:/usr/src/linux# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
0376-0376 : ide1
03c0-03df : vga+
08b0-08bf : 0000:00:0f.1
0cf8-0cff : PCI conf1
dc00-dcff : 0000:01:04.0
e400-e4ff : 0000:00:0e.0
e800-e8ff : 0000:00:06.0
ec80-ec9f : 0000:00:04.1
  ec80-ec9f : uhci_hcd
eca0-ecbf : 0000:00:04.0
  eca0-ecbf : uhci_hcd
ecc0-ecff : 0000:00:02.0
  ecc0-ecff : e1000

coconuco:/usr/src/linux# cat /proc/iomem
00000000-0009ffff : System RAM
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cbfff : Adapter ROM
000f0000-000fffff : System ROM
00100000-1ffdffff : System RAM
  00100000-003a85f5 : Kernel code
  003a85f6-004cc67f : Kernel data
1ffe0000-1ffefbff : ACPI Tables
1ffefc00-1fffefff : reserved
fcf00000-fcf0ffff : 0000:01:04.0
fcf10000-fcf1ffff : 0000:01:04.0
fd000000-fdffffff : 0000:00:0e.0
fe100000-fe11ffff : 0000:00:02.0
  fe100000-fe11ffff : e1000
fe120000-fe120fff : 0000:00:0f.2
  fe120000-fe120fff : ohci_hcd
fe121000-fe121fff : 0000:00:0e.0
fe122000-fe122fff : 0000:00:06.0
fe123000-fe1230ff : 0000:00:04.2
fec00000-fec0ffff : reserved
fee00000-fee0ffff : reserved
fff80000-ffffffff : reserved



[7.5.] PCI information ('lspci -vvv' as root)

coconuco:/usr/src/linux# lspci -vvv
00:00.0 Host bridge: ServerWorks: Unknown device 0017 (rev 32)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
 
00:00.1 Host bridge: ServerWorks: Unknown device 0017
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
 
00:02.0 Ethernet controller: Intel Corp.: Unknown device 100e (rev 02)
        Subsystem: Dell Computer Corporation: Unknown device 0135
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (63750ns min), cache line size 10
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at fe100000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at ecc0 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] #07 [0002]
        Capabilities: [f0] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
 
00:04.0 USB Controller: VIA Technologies, Inc. UHCI USB (rev 61)
(prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. UHCI USB
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, cache line size 10
        Interrupt: pin A routed to IRQ 25
        Region 4: I/O ports at eca0 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+
 
00:04.1 USB Controller: VIA Technologies, Inc. UHCI USB (rev 61)
(prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. UHCI USB
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, cache line size 10
        Interrupt: pin B routed to IRQ 26
        Region 4: I/O ports at ec80 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
00:04.2 USB Controller: VIA Technologies, Inc.: Unknown device 3104
(rev 63) (prog-if 20)
        Subsystem: VIA Technologies, Inc.: Unknown device 3104
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, cache line size 10
        Interrupt: pin C routed to IRQ 27
        Region 0: Memory at fe123000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
00:06.0 Communication controller: Motorola: Unknown device 5608
        Subsystem: Motorola: Unknown device 0000
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (250ns min, 32000ns max)
        Interrupt: pin A routed to IRQ 28
        Region 0: I/O ports at e800 [size=256]
        Region 1: Memory at fe122000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
00:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev
27) (prog-if 00 [VGA])
        Subsystem: Dell Computer Corporation: Unknown device 0135
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2000ns min), cache line size 10
        Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: I/O ports at e400 [size=256]
        Region 2: Memory at fe121000 (32-bit, non-prefetchable) [size=4K]
        Expansion ROM at <unassigned> [disabled] [size=128K]
        Capabilities: [5c] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
00:0f.0 Host bridge: ServerWorks CSB5 South Bridge (rev 93)
        Subsystem: ServerWorks CSB5 South Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 32
 
00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93)
(prog-if 8a [Master SecP PriP])
        Subsystem: Dell Computer Corporation: Unknown device 4135
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, cache line size 08
        Region 0: I/O ports at <ignored>
        Region 1: I/O ports at <ignored>
        Region 2: I/O ports at <ignored>
        Region 3: I/O ports at <ignored>
        Region 4: I/O ports at 08b0 [size=16]
 
00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev
05) (prog-if 10 [OHCI])
        Subsystem: ServerWorks OSB4/CSB5 OHCI USB Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (20000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at fe120000 (32-bit, non-prefetchable) [size=4K]
 
00:0f.3 ISA bridge: ServerWorks: Unknown device 0225
        Subsystem: ServerWorks: Unknown device 0230
        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
 
00:10.0 Host bridge: ServerWorks: Unknown device 0101 (rev 05)
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Capabilities: [60] #07 [0040]
 
00:10.2 Host bridge: ServerWorks: Unknown device 0101 (rev 05)
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Capabilities: [60] #07 [0040]
 
01:04.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly
NCR) 53c1030 (rev 07)
        Subsystem: Dell Computer Corporation: Unknown device 0135
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 72 (4250ns min, 4500ns max), cache line size 10
        Interrupt: pin A routed to IRQ 29
        Region 0: I/O ports at dc00 [size=256]
        Region 1: Memory at fcf10000 (64-bit, non-prefetchable) [size=64K]
        Region 3: Memory at fcf00000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at fce00000 [disabled] [size=1M]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
 


[7.6.] SCSI information (from /proc/scsi/scsi)

coconuco:/usr/src/linux# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
  Vendor: SEAGATE  Model: ST336607LW       Rev: DS09
  Type:   Direct-Access                    ANSI SCSI revision: 03


[7.7.] Other information:

coconuco:/usr/src/linux# cat /proc/bus/usb/devices
 
T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.6 uhci_hcd
S:  Product=VIA Technologies, Inc. USB (#2)
S:  SerialNumber=0000:00:04.1
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
 
T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=-6800/900 us (-755%), #Int=-125, #Iso= 20
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.6 uhci_hcd
S:  Product=VIA Technologies, Inc. USB
S:  SerialNumber=0000:00:04.0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
 
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  7 Spd=12  MxCh= 0
D:  Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=0915 ProdID=00e7 Rev= 1.00
S:  Manufacturer=GlobeSpan Inc.
S:  Product=USB-ADSL Modem
S:  SerialNumber=AB4A4E
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=88(I) Atr=01(Isoc) MxPS=1008 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 2 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=88(I) Atr=01(Isoc) MxPS= 912 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 3 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=88(I) Atr=01(Isoc) MxPS= 736 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 4 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=88(I) Atr=01(Isoc) MxPS= 448 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 5 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=88(I) Atr=01(Isoc) MxPS= 240 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 6 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbfs
E:  Ad=88(I) Atr=01(Isoc) MxPS=  96 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
 
T:  Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=0915 ProdID=8000 Rev= 1.00
S:  Manufacturer=GlobeSpan Inc.
S:  Product=USB-ADSL Modem
S:  SerialNumber=4B53C2
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=01(Isoc) MxPS=1008 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 2 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=01(Isoc) MxPS= 912 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 3 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=01(Isoc) MxPS= 736 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 4 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=01(Isoc) MxPS= 448 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 5 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=01(Isoc) MxPS= 240 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
I:  If#= 0 Alt= 6 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=01(Isoc) MxPS=  96 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=3ms
 
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.6 ohci_hcd
S:  Product=ServerWorks OSB4/CSB5 OHCI USB Controller
S:  SerialNumber=0000:00:0f.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms


output from lsusb:

coconuco:/usr/src/linux# lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 007: ID 0915:00e7 GlobeSpan, Inc.
Bus 002 Device 005: ID 0915:8000 GlobeSpan, Inc.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

Hope this be useful,

-- 
Santiago Ruano Rinc�n
Grupo GNU/Linux Universidad del Cauca


-------------------------------------------------------
This SF.Net email is sponsored by: thawte's Crypto Challenge Vl
Crack the code and win a Sony DCRHC40 MiniDV Digital Handycam
Camcorder. More prizes in the weekly Lunch Hour Challenge.
Sign up NOW http://ad.doubleclick.net/clk;10740251;10262165;m
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel

Reply via email to