Hello Everyone,
I recently bought the D-Link DSB-C300 camera to get a web cam going.
Unfortunately, I am unable to get it to work. I was hoping someone
on the list may have gotten this to work.
System: Debian GNU/Linux
Kernel: 2.4.9
USB Type: UHCI
Motherboard: Asus P2B-D
Processors: 2 x Pentium II 333mHz
After loading either the uhci or usb-uhci driver, I get the output below,
scrolling forever in my messages file. It occurs with both of the uhci
drivers.
Here is the output from /var/log/messages:
Sep 2 20:09:17 topeka kernel: usb.c: registered new driver usbdevfs
Sep 2 20:09:17 topeka kernel: usb.c: registered new driver hub
Sep 2 20:09:25 topeka kernel: usb-uhci.c: $Revision: 1.259 $ time 11:18:46
Aug 25 2001
Sep 2 20:09:25 topeka kernel: usb-uhci.c: High bandwidth mode enabled
Sep 2 20:09:25 topeka kernel: PCI: Found IRQ 11 for device 00:04.2
Sep 2 20:09:25 topeka kernel: usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 11
Sep 2 20:09:25 topeka kernel: usb-uhci.c: Detected 2 ports
Sep 2 20:09:25 topeka kernel: usb.c: new USB bus registered, assigned bus
number 1
Sep 2 20:09:25 topeka kernel: hub.c: USB hub found
Sep 2 20:09:25 topeka kernel: hub.c: 2 ports detected
Sep 2 20:09:25 topeka kernel: usb-uhci.c: v1.251:USB Universal Host
Controller Interface driver
Sep 2 20:09:33 topeka kernel: Linux video capture interface: v1.00
Sep 2 20:09:33 topeka kernel: usb.c: registered new driver ov511
Sep 2 20:09:33 topeka kernel: ov511.c: v1.28:OV511 USB Camera Driver
Sep 2 20:09:48 topeka kernel: hub.c: USB new device connect on bus1/2,
assigned device number 2
Sep 2 20:09:48 topeka kernel: usb-uhci.c: interrupt, status 2, frame# 58
Sep 2 20:09:48 topeka kernel: hub.c: USB new device connect on bus1/2,
assigned device number 3
Sep 2 20:09:48 topeka kernel: usb-uhci.c: interrupt, status 2, frame# 308
Sep 2 20:09:48 topeka kernel: hub.c: USB new device connect on bus1/2,
assigned device number 4
Sep 2 20:09:48 topeka kernel: usb-uhci.c: interrupt, status 2, frame# 368
Sep 2 20:09:48 topeka kernel: hub.c: USB new device connect on bus1/2,
assigned device number 5
Sep 2 20:09:48 topeka kernel: usb-uhci.c: interrupt, status 2, frame# 618
Sep 2 20:09:48 topeka kernel: hub.c: USB new device connect on bus1/2,
assigned device number 6
...
It goes all of the way up to device number 124 and then loops back to 2.
The ov511 driver is supposed to work with this device, however, it seems
the camera can't even negotiate a connection with the usb driver.
Any idea what I should try to get this to work?
Thanks in advance for any help,
julian
--
mail : julian @ catchen.org | ( topeka )
www : http://catchen.org/topeka/ | phx, az
sent : Sat Sep 15, 2001 09:06PM MST |
Whenever there is a conflict between human rights
and property rights, human rights must prevail.
--Abraham Lincoln
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
